FIG 01: ASSEMBLED COTTERED JOINT

Slides:



Advertisements
Similar presentations
What you will need to know/study to be successful for your next quiz. Unit 4 – Topics 3-5 Study Guide.
Advertisements

Fig. 4-1, p Fig. 4-2, p. 109 Fig. 4-3, p. 110.
MTRC Safety Alert issued on 31-May-2013 draw our highly attention for the innovative improvements. It is possible that a wire rope is able to come off.
Knuckle joint Applications: Elevator chains, valve rods, etc
FIG 01: ASSEMBLED COTTERED JOINT
Design of Concrete Structure I
Slide 1Fig. 22.1, p.669. Slide 2Fig. 22.3, p.670.
Remaining lectures Last lecture by Dr. Darpe: Wed, 3 rd Oct Lectures by Prof S R Kale 22 st Oct (Mon) 24 th Oct (Wed) and 31 st Oct (Wed) 11am – 11:55am.
Slide 1Fig. 17.1, p.513. Slide 2Table 17.1, p.514.
MINGGU-10-PPT-STRUKTUR –TRUSS-BETA UMM STRUKTUR TRUSS.
More on Mohr (and other related stuff) Pages , ,
Slide 1Fig. 16.1, p.488. Slide 2Fig. 16.2, p.488.
P.464. Table 13-1, p.465 Fig. 13-1, p.466 Fig. 13-2, p.467.
Presented By: SINGLE OFFSET INSTALLING RUBBER GASKETS FOR WATERTIGHT JOINTS O-RING PROFILES.
Fig. 11-1, p p. 360 Fig. 11-2, p. 361 Fig. 11-3, p. 361.
Shear - Tensile - Compression Stresses Slip Ted 126 Spring 2007.
Screws, Fasteners, and the Design of Nonpermanent Joints
Table 6-1, p Fig. 6-1, p. 162 p. 163 Fig. 6-2, p. 164.
CM 197 Mechanics of Materials Chap 20: Connections
Lecture # 2 Allowable Stress Objective:
Piston Pin Semi-Floating Pins are used to a limited extent
Chapter 11: Miscellaneous Types of fasteners
Figure 1.1 The observer in the truck sees the ball move in a vertical path when thrown upward. (b) The Earth observer views the path of the ball as a parabola.
Slide 1Fig. 3.1, p.59. Slide 2Fig. 3.2, p.59 Slide 3Fig. 3.2a, p.59.
Fasteners, Load and Stress. Loads Load is an engineering term for the forces that are exerted on a structure. Loads are considered either static or dynamic:
An Aerospace Manufacturing Perspective Aerospace Fastener Applications Part 2 1.
Statics Activities. Stress  Force per unit area (  ) Typical engineering units – psi (lb f /in 2 ) – N/m 2 Stress = Force/Area – Applied by external.
MAE 343-Intermediate Mechanics of Materials QUIZ No.1 - Thursday, Aug. 26, 2004 List three possible failure modes of a machine element (5points) List the.
Section XI Keys, Pins, & Splines.
Mechanics of Materials, 5e Chapter 1 Tension, Compression, and Shear.
Reverse Button Needle Stop Up/Down ½ Speed Stitch Width Buttons Needle Position Buttons Stitch Length Button
Structural Engineering
MAE Intermediate Mechanics of Materials Tuesday, Aug. 24, 2004 Textbook Sections 4.1 – 4.3 Forces, Equilibrium, Failure.
2/1 DIRECT SHEAR Scissors Shear stress still Force/Area but different area Strain still deflection over length but angular distortion at right angles =angle.
Factor of safety (N) = Load carrying capability
Watt-Class Beamstoppers for ALS 01/26/2011 Tom Swain & Mike Kritscher.
BRAKE UNIT Mr. Masters Tech Ed 12th. Caliper brake design Most cars from the 1990 and up are equipped with caliper brakes.
Fig. 6-CO, p p. 185a p. 185b p. 185c p. 185d.
TITLE A cotter is a flat wedge shaped piece of rectangular cross-section and its width is tapered (either on one side or both sides) from one end to.
Design of Joints, Levers, & offset Links (12 marks)
Cotter and Knuckle Joints
Machines and Devices Todor Kableshkov.
Original Configuration
ASSEMBLED COTTERED JOINT
FLIPPED CLASSROOM ACTIVITY CONSTRUCTOR- Using existing content
Date of download: 10/31/2017 Copyright © ASME. All rights reserved.
Knuckle joint Applications: Elevator chains, valve rods, etc
Determining Stress State and Sense of Shear
Fasteners.
Remaining lectures Last lecture by Dr. Darpe: Wed, 3rd Oct
$____ $____ $____ $____ $____ $____
1.6 Allowable Stress Allowable Load < Failure Load
Continuous Slot Well Screens.
Chapter 1 Stress and Strain.
Presentation on Engineering Drawing
تعارف. تعارف قواعد العمل ا الموبيل المشروبات الاحاديث الجانبية الاسئلة نفكر.
Typical Al to gold pin solder joint before and after 6 weeks in a 97% R.H. at 50 C. The test is inconclusive as the deposit is probably not a as result.
Axially loaded columns
Beams.
KELVIN MAINTENANCE GUIDE
Mechanical hardware.
Mechanical hardware.
Part II Design of Fasteners and Joints
Fig. 6-CO, p. 211.
Chapter 6 Design of Keys, Splines and Pins
07CO, p. 190.
書名:Essentials of Mechanical Engineering Design, 1/E
The Technological World
Unit 3 Plate Tectonics.
BUILDING CONSTRUCTION
Presentation transcript:

FIG 01: ASSEMBLED COTTERED JOINT Cotter joint FIG 01: ASSEMBLED COTTERED JOINT

FIG 05: SPIGOT BREAKING IN TENSION ACROSS SLOT TENSION FAILURE Cotter joint – modes of failure FIG 05: SPIGOT BREAKING IN TENSION ACROSS SLOT

Cotter joint – modes of failure SHEAR FAILURE Cotter joint – modes of failure FIG 10: SHEARING OF SPIGOT END

Cotter joint – modes of failure FIG 04: CRUSHING OF SPIGOT

FIG 07: SOCKET BREAKING IN TENSION ACROSS SLOT TENSION FAILURE Cotter joint – modes of failure FIG 07: SOCKET BREAKING IN TENSION ACROSS SLOT

Cotter joint – modes of failure SHEAR FAILURE Cotter joint – modes of failure FIG 09: DOUBLE SHEARING OF SOCKET END FIG 06: DOUBLE SHEARING OF COTTER PIN

FIG 08: CRUSHING OF COTTER PIN AGAINST SOCKET CRUSHING FAILURE Cotter joint – modes of failure FIG 08: CRUSHING OF COTTER PIN AGAINST SOCKET