ASSEMBLED COTTERED JOINT

Slides:



Advertisements
Similar presentations
Fig. 4-1, p Fig. 4-2, p. 109 Fig. 4-3, p. 110.
Advertisements

Knuckle joint Applications: Elevator chains, valve rods, etc
Team Uno 11/11/04 Bunker Curnes Product Assembly.
FIG 01: ASSEMBLED COTTERED JOINT
THREE DIMENSIONAL EQUILIBRIUM OF RIGID BODIES
Remaining lectures Last lecture by Dr. Darpe: Wed, 3 rd Oct Lectures by Prof S R Kale 22 st Oct (Mon) 24 th Oct (Wed) and 31 st Oct (Wed) 11am – 11:55am.
P.464. Table 13-1, p.465 Fig. 13-1, p.466 Fig. 13-2, p.467.
Fig. 11-1, p p. 360 Fig. 11-2, p. 361 Fig. 11-3, p. 361.
Shear - Tensile - Compression Stresses Slip Ted 126 Spring 2007.
Screws, Fasteners, and the Design of Nonpermanent Joints
Table 6-1, p Fig. 6-1, p. 162 p. 163 Fig. 6-2, p. 164.
CM 197 Mechanics of Materials Chap 20: Connections
Lecture # 2 Allowable Stress Objective:
Piston Pin Semi-Floating Pins are used to a limited extent
Chapter 11: Miscellaneous Types of fasteners
Figure 1.1 The observer in the truck sees the ball move in a vertical path when thrown upward. (b) The Earth observer views the path of the ball as a parabola.
Static and Fatigue Bolt Design
Connections and Connectors This presentation is prepared using: Structural Steel Design by McCormac and Csernak 2012 AISC Manul 13 th ed (14 th )
ME 307 Machine Design I ME 307 Machine Design I Dr. A. Aziz BazouneChapter 8: Screws, Fasteners and the Design of Nonpermanent Joints CH-8 LEC 35 Slide.
Strength of Material Shear Strain Dr. Attaullah Shah.
Fasteners, Load and Stress. Loads Load is an engineering term for the forces that are exerted on a structure. Loads are considered either static or dynamic:
LARP QXF 150mm Structure Mike Anerella / John Cozzolino / Jesse Schmalzle November 15, nd Joint HiLumi LHC-LARP Annual Meeting.
An Aerospace Manufacturing Perspective Aerospace Fastener Applications Part 2 1.
Chapter 11 keys, coupling, and seals
Statics Activities. Stress  Force per unit area (  ) Typical engineering units – psi (lb f /in 2 ) – N/m 2 Stress = Force/Area – Applied by external.
Section XI Keys, Pins, & Splines.
Mechanics of Materials, 5e Chapter 1 Tension, Compression, and Shear.
Moment Connection Requires Bolts Outside the Flanges
Overview of Mechanical Engineering for Non-MEs Part 2: Mechanics of Materials 6 Introduction – Concept of Stress.
MAE Intermediate Mechanics of Materials Tuesday, Aug. 24, 2004 Textbook Sections 4.1 – 4.3 Forces, Equilibrium, Failure.
1.5 AVERAGE SHEAR STRESS Shear stress is the stress component that act in the plane of the sectioned area. Consider a force F acting to the bar For rigid.
TEGANGAN DAN REGANGAN GESER SHEAR STRESS AND STRAIN
Hybrid Structure with Cooling John Cozzolino LARP Collaboration Meeting Port Jefferson, NY November 4-6, 2009.
Working Model Problem 15-62
POST AND LINTEL SYSTEM Alba López Odelis Lozada María Celina Val.
طراحی اتصالات Joints design. انواع وسائل ايجاد اتصال.
STEP 1: ASSEMBLE INSERT PLATES 1.Assemble insert plates by press fitting roller bearing and adapter plate into assembly 1.1 Prep all mating surfaces to.
TITLE A cotter is a flat wedge shaped piece of rectangular cross-section and its width is tapered (either on one side or both sides) from one end to.
1. Two rods, one of nylon and one of steel, are rigidly connected as shown in Fig. P.1.2. Determine the stresses and axial deformations when an axial load.
Metal Work in Masonry Module
Design of Joints, Levers, & offset Links (12 marks)
Cotter and Knuckle Joints
CAST IRON AND STEELS IDENTIFY MATERIALS AS PER COMPONENT PARTS.
FIG 01: ASSEMBLED COTTERED JOINT
FLIPPED CLASSROOM ACTIVITY CONSTRUCTOR- Using existing content
Introduction – Concept of Stress
Concept of Stress.
Knuckle joint Applications: Elevator chains, valve rods, etc
Fasteners.
Remaining lectures Last lecture by Dr. Darpe: Wed, 3rd Oct
MACHINE PARTS (FOR DCE / DIT)
1.6 Allowable Stress Allowable Load < Failure Load
Pin Restrictor System Carbide (threaded) Steel (threaded)
OASIS MAIN PRODUCTS. Rod Based Water Well Screens, Johnson Water Well Screens, Wire Wrapped Well Screens, Continuous Slot well screens, stainless steel water well casing, slotted casing, perforated casing, API casing
Water Well Screens. Johnson Screens Rod Based Well Screens.
OASIS MAIN PRODUCTS 1.Rod Based Water Well Screens 2.Johnson Water Well Screens 3.Gravel Prepack Well Screens 4.Slotted Casing 5.Perforated Casing Pipe.
Chapter 1 Stress and Strain.
Presentation on Engineering Drawing
Bone Cells or Osteocytes.
Testing the CheapBot-14 In six easy steps
Introduction – Concept of Stress
Mechanical hardware.
Mechanical hardware.
LF856 2½”-10”.
Part II Design of Fasteners and Joints
PDO Second Alert Date: Incident title: HiPo Asset Damage
Rajiv gandhi govt.polytechnic narwana
MACHINE DRAWING NAME : SYED AMER UR RAHMAN B.TECH 2 – 2
Concept of Stress.
BUILDING CONSTRUCTION
Presentation transcript:

ASSEMBLED COTTERED JOINT Cotter joint ASSEMBLED COTTERED JOINT

Cotter joint – modes of failure TENSION FAILURE F FIG 02: STEEL SPIGOT BREAKING IN TENSION OUTSIDE THE JOINT

TENSION FAILURE Cotter joint – modes of failure FIG 05: SPIGOT BREAKING IN TENSION ACROSS SLOT FIG 02: STEEL SPIGOT BREAKING IN TENSION OUTSIDE THE JOINT WROUGHT IRON ROD BREAKING IN TENSION OUTSIDE THE JOINT

TENSION FAILURE Cotter joint – modes of failure FIG 07: SOCKET BREAKING IN TENSION ACROSS SLOT

Cotter joint – modes of failure SHEAR FAILURE Cotter joint – modes of failure FIG 09: DOUBLE SHEARING OF SOCKET END FIG 06: DOUBLE SHEARING OF COTTER PIN

Cotter joint – modes of failure SHEAR FAILURE Cotter joint – modes of failure FIG 11: SHEARING AWAY OF THE COLLAR IN THE SPIGOT FIG 12: SHEARING AWAY OF SOCKET (IF dw < dl) FIG 10: SHEARING OF SPIGOT END

BEARING FAILURE Cotter joint – modes of failure FIG 04: CRUSHING OF COTTER PIN AGAINST ROD END FIG 08: CRUSHING OF COTTER PIN AGAINST SOCKET