Portable Vacuum Cleaner

Slides:

Advertisements

Similar presentations

Quick Release gripper overview and development time line.

Advertisements

! A Car Breakdown Sign ! ! Design Brief: Design and manufacture a car breakdown sign that will indicate or warn passing motorists that a car has broken.

Pipe Cutting System The evolution of Patented products Designed in Finland pipe cutting.

Team Uno 11/11/04 Bunker Curnes Product Assembly.

Fabrication of Fishtank Reservoir

ATD Assembly. ATD Assembly #1 Dewar Assembly #1 Status: Dewar has been completely assembled and vacuum tested. No vacuum leaks were detected on the outer.

Lab Zone Activity: What happens when uneven forces act on an object? Activity: What happens when uneven forces act on an object?

Fabrication of Fishtank Platform ENGR 121 living with the lab.

Activity 1.3.1a Solar Hydrogen Automobile Assembly Guide

Frog Dissection.

Old Main Group. Design Issues There are no changes to the overall Design It will remain the way it is The Attachment Issue is resolved Going to screw.

2- Crankshaft, Piston Pin, and Piston Rod Bushing.

Manufacturing Assembly Plan P Mechanical Spine Test Platform.

5.8m Solar House Installation Instruction. Introduction Step 1. connect the corner panels Step 2. connect the back and side wall panels Step 3. Install.

Unit 53 Metalwork Technology and Practice

Boring MEEG 217 Suraj Pandey. Introduction One of the most versatile machine tools; used to bore holes in large and heavy parts as engine frames, machine.

Caterpillar CaterpillarBot is a robot that can pass the bumpy road by using caterpillar.

Marie Zubatá 3. A.  Centrifugal pumps are a type pumps used to convey liquids or gases by the means of a rotating impeller, which increases the pressure.

Portable Power Tools Safety and Use. Portable Power Tools Cordless Drills/Drivers Corded Drills Random Orbit Sander Dual Action Sander Jigsaw Circular.

SeaPerch Design Challenge and Construction Overview.

CONNECTING MODULE – conveyor 2 – sorting mechanism (waste bin) 3 – connectors (air, cooling water)

RPI Storage Box with Removable Dividers Kaleigh Iler: Columbia HS & Nabihah Azhari: Troy HS.

Vacuum chuck for probe station contacts: Howard Wieman work: cell: Eric Anderssen

Printed 10/7/2011 SCOUT, REV5, WIRING KIT, GUIDE SONAR Connector: JST Length: 6.5 inches 28AWG Start: BreakFly End: Sonar 0, 1 FEMALE Connector: JST.

Estimating the Efficiency of a Parallax Servo living with the lab.

ENGINEERING NOTES KID WIND By: Luis.C Miguel.M. Materials List  Screws……………….. ( base attachment )… …..#26  Nails………………….. ( Base attachment ) #10.

Scooter ScooterBot is a robot that drives using Servo Motor as steering system.

Bed Monitoring: Objective Bed sensors determine if patient is in bed Switches in a grid pattern are used to determine the patients location Can be used.

FIVE TIGERS ENGINEERING CO., LTD. DYNAMIC BALANCING APPLICATIONS.

ID 1.75 Material list: aluminum ¼ X ¾ X 6 in flat bar ¾ X 6 in round stock 1 X 6 in round stock 2 ea 5/16 heli-coil Weld 1” joints.

What do I have to do? Cause a motor to turn the center arm. attach motor to frame can redesign the center arm piece as needed use bushings or bearings.

Week 13 Deliverables Team Highlander. Modifications from last Mock-Up Lever assembly is offset from walker Ski assembly is now solid Levers swing upward.

Andrea Wyman Mechanical Engineering Student. Objective Andrea Wyman (864) Pursuing an engineering position to gain experience.

Fabrication of Fishtank Reservoir ENGR 121 living with the lab.

Coordinate Detector: prototype design General idea about the Coordinate Detector (CDET) so far: Three independent vertical planes with 15 cm plastic shield.

Pump fabrication – day 1 living with the lab group B will make their pumpgroup A will draw their pump.

Orbit Engineering Moonbuggy Wheels James Roland Jacob Lloyd Ian Henry Kevin Beckman.

#UniversalHealth selfie display Quick guide December 2015.

SeaPerch Electrical System. Electrical System Overview Assemble the control box. Make the Cat5 connector. Wire the motors to the tether. Wire the control.

Jigs and Fixtures A Basic Look © 2013 Project Lead The Way, Inc.Computer Integrated Manufacturing.

CH 6.5 Electric Power Tools.

What does engineer/engineering make you think of?

SeaPerch Electrical System

SeaPerch Structural System

SeaPerch Structural System

QUICK START GUIDE FOR BUILDING THE CLAWBOT

Pump Project Overview.

Fabrication of Fishtank Reservoir

Introduction to Power Tools

Machining Processes: Cutting

6. Disassembly & Reassembly

Flag Installation on Roll-up Signs

Flag Installation on Roll-up Signs

SeaPerch Structural System

The evolution of pipe cutting Patented products Designed in Finland Pipe Cutting System.

יחסים בין אחים כמראה ליחסי ה- Attachment במשפחה

זכויות סוציאליות.

7 Fire Extinguishers.

Removes these two screws that attach the Controller to the Hopper Box.

PP 14° Bi-Weekly meeting S1-Global, June 1, 2009

SeaPerch Structural System

DNA Modeling How to make your own DNA.

BUILDING AN AUTONOMOUS QUADCOPTER.

After service guide for changing PCB

SeaPerch Electrical System

Presentation transcript:

Portable Vacuum Cleaner Cavin Israel Penn State—ME 340 Spring 2015

Background Design a portable vacuum to suck 1 cup of rice in under 60 seconds. Portable vacuum designed from a cordless power drill.

Axial Impeller 3 inch axial impeller designed in SolidWorks. 3D printed in Penn State printing lab.

Connecting Impeller to Motor Used vertical mill and lathe to produce connector to attach the impeller to the drill motor. Made from 6061-T4 Aluminum.

Secure Motor to Vacuum Housing Designed in Solidworks and cut using a water jet. Made from 6061-T4 Aluminum.

Vacuum Nozzle Designed in SolidWorks. 3D printed and attached to the front of the vacuum to pick up rice.

Vacuum Assembly Impeller secured to motor (front).

Vacuum Assembly Impeller secured to motor (rear).

Vacuum Assembly PVC Piping used for vacuum housing. Cordless drill handle, trigger, and battery used to operate and hold vacuum.