Pneumatic Tool Safety By John Templeton.

Slides:

Advertisements

Similar presentations

FHM TRAINING TOOLS This training presentation is part of FHM’s commitment to creating and keeping safe workplaces. Be sure to check out all the training.

Advertisements

Safety : Power Tools Introduction to Industrial Technology Spring 2014 Mr. Shubert.

HAND and POWER TOOL SAFETY

Safe use of Tools and Equipment at Height Guidance Richie Adams Egyptian Drilling Company.

Power Tools Safety. Portable Circular Saws Stock must be well supported in such a way that the kerf will not close and bind the blade.. Thin materials.

Evolution Industries, Inc. Updated October 1, 2010.

Lock Out/Tag Out Training Lock-Out/Tag-Out OSHA Definition. Lockout/Tagout (LOTO) refers to specific practices and procedures to safeguard employees.

Portable Tools.

Hand and Portable Power Tools Hazard Recognition.. Inspect tools daily Tool Fits Job.

Hand and Power Tool Safety

Proprietary and Confidential HAND TOOL SAFETY Safety Leadership Training Series "Our loss control service is advisory only. We assume no responsibility.

Standard 29 CFR Part Welding, Cutting and Brazing Training.

Lockout/Tagout (LOTO):

Presented by Environmental Health and Safety

Nail Gun Safety. Employer –Responsible for safe condition of tools Employee –Responsible for properly using and maintaining tools.

Power/Hand Tools Valley City State University | Facilities Services | OSHA Office of Training & Education.

Tools – Hand and Power 1926 Subpart I - Tools – Hand and Power

Hand & Power Tool Safety

AIR COMPRESSORS & STEAM CLEANERS. Pressurized air is produced by an air compressor. Air compressors are used daily in automotive shops. They are used.

School Safety Training

Lockout Tagout Tryout (LOTO). The purpose of the Lockout Tagout Program is to protect you. Rain for Rent incidents include employees being sprayed with.

Oklahoma State University EHS Lockout/Tagout Standard Proper Lockout Procedure.

/0309 Copyright ©2003 Business and Legal Reports, Inc. BLR’s Safety Training Presentations Lockout/Tagout Refresher 29 CFR

Lockout/Tagout Training Division of Facilities Construction and Management 2001.

JEOPARDY! HAND TOOLS $100 $200 $300 $400 $500 $100 $200 $300 $400 $500 $100 $200 $300 $400 $500 $100 $200 $300 $400 $500 $100 $200 $300 $400 $500 $100.

Tools – Hand and Power.

Annual Refresher Training Tools and Machine Guards.

BASIC WOODSHOP SAFETY. What are the five basic components of a good safety plan for the woodshop? A – Know the rules B – Dress for safety C – Use tools.

1 Portable Powered Tools Use the Right Tool the Right Way.

Electrical Safety in Construction. Objectives In this course, we will discuss the following: Common electrical hazards Standards relating to those hazards.

Hand and Power Tool Safety Standards Training

Joe Bateman, ISRI Safety 1 Machine Guarding. ISRI Safety 2 Introduction Machine guards are essential for protecting workers from needless and preventable.

Hand and Portable Power Tools 29 CFR, Subpart P

PPT 10-hr. Construction – Tools v Created by OTIEC Outreach Resources Workgroup Tools – Hand and Power 10-Hour Construction Outreach.

Hand and Power Tools for construction. Basic tool safety  Keep in good condition  Right tool for job  Inspect tools  Operate tools correctly  PPE.

Basic Lockout Guidelines

Write down three safety rules we talked about in the past few days. Talk with someone near you and see how many ways are out there to lift a car for service.

Electrical Work Practices City of Council Bluffs Presented by: SilverStone Group © 2012 Zywave, Inc. All rights reserved.

Welding Safety Test.

ALL ABOUT PNEUMATIC TOOLS. The pneumatic tools normally used for heavy equipment extrications are the percussive type tools, such as the rivet hammer,

Hand and Power Tool Safety. DIFFERENCE BETWEEN Hand Tools AND Power Tools 4 Hand tools Have no power source, other than the physical force applied by.

Hand and Portable Power Tools OSHE 112, Spring 2015

Hand and Portable Power Tools OSHE 112, Spring 2016

LOCKOUT/TAGOUT/VERIFY

Lockout/Tagout Standard

Safety at SM FIRST Lab.

Tools and Equipment Fundamentals

Nail Gun Coach Ketcham Productions.

UCG- TAG OUT LOCK OUT.

CONTROL OF HAZARDOUS ENERGIES (LOCKOUT / TAGOUT)

Teknologi Dan Rekayasa

OVERVIEW Control Of Hazardous Energy.

Compressed Air Safety.

Pneumatic Tool Safety By John Templeton.

Preparing to Use a Table Saw

Mechanical Power Press Safety

Abrasive Wheel Machinery

Personal Protective Equipment

ABRASIVE WHEEL MACHINERY

Hand & Power Tools, Subpart I

Presented by Environmental Health and Safety

Mechanical Power Press Safety

Compressed Air Safety.

evGrand Prix Shop/Garage Safety

Compressor Operating Instructions

Presentation transcript:

Pneumatic Tool Safety By John Templeton

Objective Identify safety precautions used when operating pneumatic tools.

Definition ____________________________________________ ____________________________________________ ____________________________________________

Nails Nails come in different forms for different purposes. ____________________________________________ ____________________________________________

Safety There are several dangers associated with the use of pneumatic tools. ______________________________________________ ______________________________________________ tool’s attachments or by some kind of fastener the worker is using with the tool.

Safety Pneumatic tools must be checked to see that the tools are fastened securely to the air hose to prevent them from becoming disconnected. ___________________________________________ ___________________________________________ attaching the air hose to the tool must also be used and will serve as an added safeguard.

Safety Eye protection is required, and head and face protection is recommended for employees working with pneumatic tools. ____________________________________________ ___________________________________________.

Safety Use common sense when operating compressed air tools. Never spray above the neck or point tools in the direction of someone Stay clear of tool exhaust ______________________________________________

Safety ____________________________________________ ___________________________________________.

Air Hoses The same precautions should be taken with an air hose that are recommended for electric cords, because the hose is subject to the same kind of damage or accidental striking, ____________________________________________ ___________________________________________.

Safety Devices Pneumatic tools that shoot nails, rivets, staples, or similar fasteners and operate at pressures more than _________________________square inch (6,890 kPa), must be equipped with a special device to keep fasteners from being ejected, unless the muzzle is pressed against the work surface.

Activity Develop 10 safety rules for using the pneumatic air tools in our shop.