The Architect’s Scale.

Slides:

Advertisements

Similar presentations

How to Find a Fraction on a Number line

Advertisements

Scale Drawings Cornell Notes with Summary

5.8 Scale Drawing and Models

SCALE FACTORS MODELS & MAPS In addition to level 3.0 and above and beyond what was taught in class, the student may: · Make connection with other.

Scale Drawings Today you will learn to: identify similar figures

EXAMPLE 4 Use a scale drawing SOLUTION Maps The scale of the map at the right is 1 inch : 26 miles. Find the actual distance from Pocahontas to Algona.

How to Identify a Bolt. The parts of a Bolt A Scale (or Ruler) is used to determine the dimensions of a bolt.

Using the Scale Ruler What is Scale? What are all these tiny lines anyway?

Using the Ruler: Measuring to the Nearest ½ Inch

BCT 102 Printreading Architect Civil Engineer Reading & Scale Use.

The three-sided version of the architect’s scale has ten separate scales, paired in five groups of two: 1-inch and 1/2-inch 3/4-inch and 3/8-inch 3/16-inch.

Architecture From Math to Building Design. Scale Scale is a Ratio Scale is a Ratio A ratio compares one thing to another A ratio compares one thing to.

Digimap Training Workshops Map scales Any map is a scale representation of the Earth’s surface Scale may be defined as: – the ratio between distance measured.

Measuring using… INCHES FEET YARDS MILES

Using a Ruler to Measure USCS to Metric / SI

Bed Separation Single and Bunk Beds –A minimum of 6 feet separation must be maintained between beds when heads of beds are oriented in the same direction.

Science Measuring Tools by: Kathy Furgang

Today we will identify fractions on a number line.

AREA OF A TRIANGLE. Given two sides and an included angle:

Rulers or Tape Measures

FOUNDATIONS OF ENGINEERING AND TECHNOLOGY SCALING A DRAWING.

Scale Drawings and Models

1 Introduction to Engineering Dimensioning - 1 Goals Understand units and measures Understand concepts of scaling and types of scales Turn in Lab 2 report.

Measurement. 3 Parts to Measurement: 1. a numeric value 2. a unit 3. an estimation of the amount of error.

Introduction to Drafting and Design

Notes Over 11.1 Proportions Vocabulary Proportion - an equation that states that two ratios are equal. Cross Product Property - the product of the extremes.

*LengthLength *Why do we measure objects? *What do we use to measure objects? *How many inches are on a ruler?

Gateway – Unit 7 – Green Architecture

Measuring Length Created by Craig Mason. Measuring Length ½ of an Inch To the Inch ¼ of an Inch Conversions PowerPoint Created by Craig Mason.

Weight Changes in weight are an indicator of the patient’s condition and progress Baseline measurement on admission Measure in kilograms (kg)

How to read an Architect’s Scale

On a floor plan of her room, the length of Hailey’s bed is 3 inches. If the scale of her floor plan is inch = 1 foot, what is the actual length of her.

All About Rulers!. Facts: One ruler has 12 inches and about 30 centimeters. 12 inches equals 1 foot…. Not this kind of foot:

How to read a ruler. 1 inch is split into 16 increments. Usually, you’ll see a 1/16 on a ruler.

How to Find a Fraction on a Number line A number line and a ruler are very much alike

3:00. 2:59 2:58 2:57 2:56 2:55 2:54 2:53 2:52.

Conversion Graphs Learning Objective: Be able to use conversion graphs. 27/01/10.

Learn How To Read a Ruler in Just a Few Steps. ONE FOOT = 12 INCHES As you can see there are 12 inches in one foot ~As a side note, there are 3 feet in.

Matter: Anything that is real & takes up space. All Solids, liquids & gases. Matter = Stuff MATTER MATTERS.

Opener Simplify or Solve: 1. x + 3(x – 6) 2. 4x + 5 = (3 + x)y + x² + 2xy 4. 6(x + 2) + 4x x + x – 6 = 3 6. –(x + 7) = -3.

Drawing to Scale Chris Wakefield HTHMA. Why Draw to Scale? To create a drawing which is proportionately the same To create a drawing which is proportionately.

What is scale? Think Write Share. Scale…… Gives us the relationship between the measurements and the drawing or model and the measurements of the real.

How to read an Architect’s Scale

Come ti chiami? Mi chiamo Anthony..

Pre-Engineering Introduction to CADD Scales.

How to read an Architect’s Scale

How to Read an Architect’s Scale

Gateway – Unit 7 – Green Architecture

Applications of technology

How to Identify a Bolt.

Top Fire Protection Services Ottawa available on Dubinskyconstruction

Measurement GTT – Unit 7 – Green Architecture © 2012 Project Lead The Way, Inc.Green Architecture.

Maps and scale drawings are:

A scale drawing is a drawing in which all parts of the drawing are reduced or enlarged by the same scale factor. A scale is a ratio that compares the measurements.

Map Scale Geography.

Orthographic Projection 2

How to Find a Fraction on a Number Line

Bed Separation Single and Bunk Beds

4n + 2 1st term = 4 × = 6 2nd term = 4 × = 10 3rd term

DO NOT OPEN YOUR BINDER UNTIL INSTRUCTED

Main Idea and New Vocabulary Example 1: Use a Map Scale

Goal: The learner will use proportions to find measures of objects.

Gateway – Unit 7 – Green Architecture

7.2 Similar Polygons Two polygons are similar (~) if and only if their

Bellwork A scale model of the Statue of Liberty is 15 inches tall. If the Statue of Liberty is 305 feet tall, find the scale of the model. A map has.

Architects Scale Tech Ed S-O High School.

HOW TO READ A SCALE RULER

Presentation transcript:

The Architect’s Scale

11 Different Scales And a 12in standard ruler Scale - Size Representation ---------------------------------- 3" - 1/4th 1.5" - 1/8th 1" - 1/12th 3/4" - 1/16th 1/2" - 1/24th 3/8" - 1/32nd 1/4" - 1/48th 3/16" - 1/64th 1/8" - 1/96th 3/32" - 1/128th And a 12in standard ruler

Example Scales

Reading Feet.

Reading Feet. 48’ 16’ http://www.udel.edu/present/Becky/ruler/

What's before 0? Line one end up with 0 It's the "inches" Line one end up with 0 Then move it Back past 0 until it stops on a line Now you can read the inches.

Reading Inches

http://www.udel.edu/present/Becky/ruler/