Correct blade installation

Slides:



Advertisements
Similar presentations
An Introduction To Marine Steam Propulsion Plant [Source: US Navy]
Advertisements

Fire Behaviour Ventilation. Aim To provide students with information to give them an understanding of the behaviour of fire.
CM 4120 Julie King Original Presentation by Todd King and I edited it.
Boilers This is session 22 in curriculum manual.
Basic Refrigeration Cycle
Cooling Tower Maintenance Training.
Jet Engine Design Idealized air-standard Brayton cycle
Jet Engine Design diffuser compressor combustion chamber turbine nozzle P=constant q out q in T s 1-2 Isentropic compression in.
“Energy Efficiency Guide for Industry in Asia”
Unit 206: Domestic hot water systems
Chapter 4.2: Flow Across a Tube Bundle Heat Exchanger (Tube Bank)
Rob Midgley Oils and Oil Analysis deHavilland Moth Club.
Industrial Ventilation - A major control measure Dr. AA, UTM.
Thermodynamics Professor Lee Carkner Lecture 18
Refrigeration and Cooling Principles for Potato Storages
COMMERCIAL REFRIGERATION
Heat exchangers The device at which heat exchange between two fluids at different temperatures and separated by a solid wall occurs is called heat exchanger.
Irfan Ahmed Operations Department
Steam Traps Function and Types.
Sawing. Reciprocating saws (power hack saw) being replaced by horiz band saws only cuts in one direction up to 24” x 24”
COOLING TOWER Prof. Osama El Masry.
Best Practices in HVAC Design/Retrofit
Ventilation for Low Energy Buildings
NFPA 54 National Fuel Gas Code Boiler Manufacturer ANSI Standards Local Codes Vent Manufacturer.
INTRODUCTION Definition:
Plant Utility System (TKK-2210) 14/15 Semester 4 Instructor: Rama Oktavian Office Hr.: M-F
Partial Evaporation Example 1/31/2007. Shell and Tube Heat Exchanger.
Heat Transfer Equations For “thin walled” tubes, A i = A o.
FMTV COOLING SYSTEMS 4/23/2017.
TPO Lap Splicing Lap Splicing Lap splicing on a TPO system is defined as joining two separate sheets, by way of heat welding, into one monolithic sheet.
Tempest Blower SECTION: Tools and Equipment ISSUED: REVISED: ##-####
Roofs The exterior upper part of a house or building – to protect the interior from the elements (heat, cold, rain, snow etc.)
MECHANICAL ENGINEERING FOR SYSTEM BALANCE ASHRAE MEETING 2/15/2007 NORTHERN NEVADA CHAPTER 126 MATT BRENNAN, TBE.
1 HVACR215 – Mechanical for Oil Oil Combustion. 2 Combustion The burning of a substance. Rapid Oxidation The burning of a substance. Rapid Oxidation.
Placing Vapor Distribution Systems and Appliances into Operation MODULE 4 Identifying Venting Requirements and Characteristics.
Cooling Systems What does the cooling system do?
Thermal Power Station.
Heat Transfer Equations For “thin walled” tubes, A i = A o.
Condensing Hydronic Heat Exchangers Make-Up Air Units Meets.
JET ENGINE INTERNAL COOLING AND SEALING PREVENTING BURN OUT OF THE HOT SECTION.
Furnaces Today’s Agenda Function of a furnace Furnace operation Fuel Furnace parts Furnace drafts Furnace designs.
Heat Transfer: Physical process by which thermal energy is exchanged between material bodies or inside the same body as a result of a temperature difference.
Water as coolant Cooling system of a car engine
Appendix A.
ATCA COOLING PROJECT INTERSHIP FINAL PRESENTATION Piotr Koziol.
Heat Pumps Presentation by: Rana Itani. Objective To familiarize audience on the components of a heat pump and how it works.
Theoretical Consideration Choose the best design Study the efficiency of energy conversion at specific speed. Power Coefficient Tip Speed Ratio Conversion.
PREVENTING BURN OUT OF THE HOT SECTION
AC’s- integral part of life. Rising temperature and high standard of living have made AC’s an important part of our lifestyle. The AC distributes conditioned.
Space Air Diffusion. Fundamentals  Objectives – thermal comfort and indoor air quality – even space air conditions – acceptable air cleanliness – acceptable.
Hydraulic axial forces acting on a Francis runner.
Unit 13 Oil-Burning Equipment
Air Distribution Control
Date of download: 10/12/2017 Copyright © ASME. All rights reserved.
AIR CONDITIONING.
«Development and analysis of heat exchanger combined with fire tank with a view of its application as part of geothermal heat pump»
Air Distribution Control
Internal Training Module
S.T.B.S College of Diploma Engineering, SURAT
Factors to Consider When Choosing a New Air Conditioning Unit
COOLING TOWER.
Motivation Performance of power plants using ACC may largely be affected by wind conditions Up to 10% reduction in net plant power output for 10 m/s wind[1]
T-6B On-Board Oxygen Generation System (OBOGS)
Hydraulic axial forces acting on a Francis runner
FORCED CONVECTION AND EFFECTIVE VELOCITY
Manual D Duct Sizes Room Cooling CFM % Total CFM Heating CFM Kitchen GR Dining Bed Bed 3.
1.5: Velocity-time graphs
3 x Transformer boards ISO View Fans Oriented as in Super Micro Case
T-6B On-Board Oxygen Generation System (OBOGS)
Presentation transcript:

Correct blade installation

Blade installation

Checking blade angle / track on fan ring or fan stack

Checking blade angle / track on fan ring or fan stack

Checking blade angle / track on fan ring or fan stack

Checking blade angle using an Exact-A-Pitch® protractor

Tip seal honeycomb

Tip clearances > 5’ – 9’ (min. 1/4”) and (max. 1/2”)

Inlet bells

Air-Cooled Heat Exchangers ® Induced Draft Fans positioned above the exchanger bundle High velocity Reduces hot air recirculation Plenums protect exchanger bundle from elements Better air distribution across the bundle

Air-Cooled Heat Exchangers (cont.) ® Fans & mechanicals positioned below bundle H.P.requirements vary with temp. Maintenance personnel protected from high exit-air temperatures Well suited for high temperature service Forced Draft

Feedback: Privacy Policy Feedback
Do Not Sell My Personal Information
About project: SlidePlayer Terms of Service

© 2025 SlidePlayer.com. Inc. All rights reserved.