Destructive testing of Weldments

Slides:



Advertisements
Similar presentations
Material Testing. Reproducible evaluation of material properties Material response to varying loading conditions, including magnitude, cycling, and mode.
Advertisements

ME 240: Introduction to Engineering Materials Chapter 8. Failure 8.1 CHAPTER 8.
Material testing Lesson 2.
TED 316 – Structural Design
IMPACT TEST EXPERIMENT # 7 Instructor: M.Yaqub. IMPACT LOAD  Shock load or sudden load is referred as impact load.  In order to select a material to.
Chapter 11 Mechanical Properties of Materials
Manufacturing Technology
Materials Engineering – Day 2
EXPERIMENT # 3 Instructor: M.Yaqub
LECTURER 3 Fundamental Mechanical Properties (i)Tensile strength
Lecture # 7 Mechanical Properties(Cont) Intended learning Outcomes: After the end of this lecture the student should be able to: 1- Evaluate and measure.
Dr. Ali I. Tayeh First Semester
LECTURER6 Factors Affecting Mechanical Properties
Advanced Manufacturing Laboratory Department of Industrial Engineering Sharif University of Technology Session #19.
Mechanical Properties Testing
ITW Structural and Strength of Materials Teaching Laboratory Civil & Materials Engineering UIC November 2009.
Pressure Vessels.
Mechanical Properties
Unit V Lecturer11 LECTURE-I  Introduction  Some important definitions  Stress-strain relation for different engineering materials.
Chapter 7 Fatigue Failure Resulting from Variable Loading
Mechanical Properties of Materials
Destructive Examination & Testing 2 Destructive Examination Destructive Examination renders the weld or material unfit for further service.
Chapter 7 §7.3 Technical Properties of Construction Steels Tensile property  Stress-strain chart of soft steel  Strength  Plasticity Impact toughness.
Properties of Refractory Castables Tina Stendal Svendsen Product Manager 1.
Welding Design 1998/MJ1/MatJoin2/1 Design. Lesson Objectives When you finish this lesson you will understand: Mechanical and Physical Properties (structure.
Chapter 9-Statics, Dynamics and Mechanical Engineering Objectives and what should you Know: What are statics and Dynamics? What are the Newtons’s three.
MECHANICAL TESTING.
§7.3 Technical Properties of Construction Steels Tensile property  Stress-strain chart of soft steel  Strength  Plasticity Impact toughness Cold-bending.
Machine Design I (MCE-C 203) Mechatronics Dept., Faculty of Engineering, Fayoum University Dr. Ahmed Salah Abou Taleb Lecturer, Mechanical Engineering.
Machine Design I (MCE-C 203) Mechatronics Dept., Faculty of Engineering, Fayoum University Dr. Ahmed Salah Abou Taleb Lecturer, Mechanical Engineering.
Engineering materials. Materials and civilization Materials have always been an integral part of human culture and civilizations.
Materials and the properties products Dr. Norman Swindells, CEng, FIMMM Ferroday Ltd, UK 21/04/2015(c) Ferroday Ltd 2015, Vico Equense 1.
Engineering properties of rock Prepared by :- Kumari Pooja 3 rd sem civil department 13oo
STRUCTURES Young’s Modulus. Tests There are 4 tests that you can do to a material There are 4 tests that you can do to a material 1 tensile This is where.
Physical properties Enrollment numbers Government engineering collage,Palanpur sub:- Applied.
Exploration of Materials Properties: Every material has its own properties. When choosing materials for our design work, we must first analyze and compare.
GENERAL CONSIDERATION IN DESIGN OF MACHINE ELEMENTS
K . J . INSTITUTE OF ENGINEERING & TECHNOLOGY (064)
The various engineering and true stress-strain properties obtainable from a tension test are summarized by the categorized listing of Table 1.1. Note that.
Properties OR Working Characteristics
Material Behaviour. Produced by Neil Liggett.
Eduardo Ismael Hernández UPAEP University, MEXICO
Development of the constructions of the transport
Properties & Characteristics
Lecturer: Dr. Frederick Owusu-Nimo
Teknologi Dan Rekayasa
Teknologi Las Kapal Destructive Testing.
Introduction We select materials for many components and applications by matching the properties of the material to the service condition required of the.
Choosing of materials Higher Product Design.
Design of parts for static loading
LECTURER 3 Fundamental Mechanical Properties (i)Tensile strength
COMPARISON OF WELD METAL PROPERTIES OF C-Mn MULTI-RUN WELDMENTS CONTAINING TITANIUM - AT DIFFERENT LEVELS OF NITROGEN Fig.2- The actual measured tensile.
Mechanical Properties of Metals
Dr. Omar S.M.J.Ali PhD Orthodontic
Machine Design What is the importance of Machine Design for engineers? What is Machine Design? Creation of new and better machines AND Improving existing.
Poisons Ratio Poisons ratio = . w0 w Usually poisons ratio ranges from
Identifying Metals and Their Physical Properties
Manufacturing Part 2 © 2011 International Technology and Engineering Educators Association, STEMCenter for Teaching and Learning™ Foundations of Technology.
STEEL AS A CONSTRUCTIONAL MATERIAL
Material Testing.
1/18/2019 6:28 AM C h a p t e r 8 Failure Dr. Mohammad Abuhaiba, PE.
LECTURE-I Introduction Some important definitions
Mechanical Properties: 1
Hardness Resistance to indentation.
Applied Technology High School (ATHS)
Simple Stresses & Strain
Choosing of materials Higher Product Design.
GCSE Revision Resistant materials
Introduction to Strength of Materials Lecturer; MOHD FIRASATH ALI.
Mechanical Property 기계적 성질
Presentation transcript:

Destructive testing of Weldments Welding Technology/5.6 Destructive testing of Weldments

Destructive Testing of Weldments Destructive weld testing, as the name suggests, involves the physical destruction of a completed weld to evaluate its strength and characteristics. Welding Technology/5.6 Destructive testing of Weldments

Toughness testing In actual practice, engineering components during service are invariably subjected to various kinds of loads namely static and dynamic loads which are classified on the basis of the rate of change in magnitude of load and direction. Dynamic loads are characterized by high rate of change in load magnitude and direction. Reverse happens in case of static loads. In the hardness test and tensile tests, load is increased very slowly that corresponds to the behaviour of material under more or less static loading condition. Moreover, very wide range rate of loading (0.0001 to 1000mm/min) can be used in tensile test. Welding Technology/5.6 Destructive testing of Weldments

Toughness testing The toughness test simulates service conditions often encountered by components of the system used in transportation, agricultural, and construction equipment. A material high impact resistance is said to be a tough material. Toughness is the ability of a material to resist both fracture and deformation. Welding Technology/5.6 Destructive testing of Weldments

Toughness testing Welding Technology/5.6 Destructive testing of Weldments

Toughness testing Welding Technology/5.6 Destructive testing of Weldments

Toughness testing Welding Technology/5.6 Destructive testing of Weldments