Plastic Recessed Kit for Escape Sign

Slides:

Advertisements

Similar presentations

F AST T RACK REMOTE SWITCH WIRING SET UP FOR THE LIGHT BoardPlug Power strips relay Wiring Harness.

Advertisements

Using the Passive Voice Writing Consultant Presentation EG 1003: Intro to Engineering and Design NYUs Polytechnic School of Engineering.

Introducing Geoliner 660 an Imaging Evolution  New Multiprocessor Camera for increased Speed  Enhanced Cameras are VODI TM equipped for increased operator.

Assembly Manual Mike Fortney 04/09/2004 CricketSat Receiver.

CricketSat LP (Transmitter) Assembly Instructions This is the instruction slides for the assembly of a transmitter board. This is the board that will fly.

ESD Constant Monitor System Packaging Bench set-up.

We Design Innovative Bus Interiors LED Retrofit Systems Designed ForPretoria Hadley/Transmatic L-20 and Hadley/Transmatic L-20 Fluorescent Aisle Lighting.

Applied Control Systems

1 Ladder assembly steps HFT PIXEL updated for ultimate chip ladders 2/12/2012 ladder fixture u.SLDASM.

Assembly Manual Mike Fortney 04/02/2006 CricketSat Receiver.

Knowledge to Shape Your Future Electric / Gas / Water Information collection, analysis and application MekElekItroniks Design Review Battery Charger Project.

ULTRA RT8 LED 347V Recessed Downlight Kit.

Electrical Engineering. A circuit is a combination of different components that allow electricity to flow through them. Each component serves its own.

The First Central Emergency & Standby Lighting System Combining Storage Batteries & Generator Input 1 1.

Die Cast – Nickel Die Cast – Black Metalized Plastic Black Plastic Grey Plastic Plastic - Assorted Colors –Available only on 972 Series.

Controls, Switches and Energy Transformation

Making a PCB Report and ppt – presentation 1.)Structure 1.1)Making the PCB 1.2)Assembling a circuit )The components I choose )They functions.

IPC-SM Board Size & Panel Construction In order to fully utilize the automation technology associated with surface mount components, a designer.

Traditional Fixtures & Fittings 1 J. Byrne Fixtures & Fittings J. Byrne

AUTOMATIC PLANT WATERING UNIT. NAMECOURSE  BACKGROUND  PROBLEM STATEMENT  OBJECTIVES  FUNCTIONS  SCHEMATICS OF PROTOTYPE & WIRING  RESULTS  CAPITAL.

Overview ET-PLC (Intro, Update) Opportunity Key points to review.

PS1500B Battery Replacement Procedure. 1.Pull off the front panel.

Shop Built Magnetic LED Light Bob Clark Aug, 11, 2011.

1 B. Braun SpaceStation – Product details Overview Flexibility in use Typical configurations.

Counter Bore. Spot Facing – Provides a true bearing surface for a washer. Counter boring – Provides a recess for a bolt head, bushing or pin.

ArchiLED A modular LED lighting system. ArchiLED easy assembly The plastic grips (two per module) should be attached in one line using screws or double-sided.

Adding to your Diagnostic Station Adding thermometry The temperature module attaches to the top of the BP module. It is made up of the following two.

Comp 2 Comp 1 EcoLEd Bandiera EUR ECO ………. nomic LED ………. technology Bandiera … EM luminaire Main features: cost-effective price autonomy 3h SA version.

18240 Element two - Components INPUTS OUTPUTS PURPOSE TYPICAL USE.

SCRS’ Education Committee Presents Kool Tools from SEMA 2015 January, Palm Springs, Ca.

Using the Passive Voice Writing Consultant Presentation EG 1003: Intro to Engineering and Design NYU’s Polytechnic School of Engineering.

Year 8 Fuse Tester Design & Technology PCB Information Fixed value resistors 470R = Yellow, Purple, Brown This component is soldered directly onto the.

Harris Lighting’s Patent Pending LED Door Retrofit – LDR System Innovative design is first LED.

Residential Security, Access Control, and Surveillance Copyright © 2005 Heathkit Company, Inc. All Rights Reserved Presentation 5 – The HAI Omni II Controller.

Aluminium die cast; Glass; CLASS II; 8W 24 LED (12+12) 180lm SE-SA-PS; 24W 36 LED (18+18) 270lm SE-SA-PS.

FIRST: Start by opening the side flaps of the box, revealing her interior, where later will place each component.

A Simple Electric Circuit As A Security System

Using the Passive Voice

Instructions for Diaphragm Replacement Cat. Nos. 2052B-01, 2054B-01

Light Emitting Diode: LED

Light Bulb Changing Procedure

ASSEMBLY/INSTALLATION INSTRUCTIONS ASSEMBLY AND INSTALLATION

CAUTION GENERAL TOOLS REQUIRED ASSEMBLY AND INSTALLATION

Cover-Gear Box assembly

Nimbus MODUL Q 64 IN Description

Redundancy Switching Components

Yeti 400 Reprogram SOP 5/1/2017, Yeti firmware rev. 2.0.

Case Design Version 2 P13036 – Notification Alert William Johnson.

The Relay based Multiplexer

CAUTION GENERAL TOOLS REQUIRED ASSEMBLY AND INSTALLATION

ULTRA RT8 LED 347V Recessed Downlight Kit

EVERLINE® LED Emergency Drivers

सोलर पॅनेलचा उपयोग करुन रीचर्जेबल टॉर्च बनवणे.

CM-75 SERIES PUSH PLATE SWITCHES No One Does Wireless Door

Required tools for installation of a V-1020C Speaker with V-9914M-5 Metal Bridge.

A modular LED lighting system

Projects: Project Name- Electrical Accessories

ESA08 Ceiling Recessed Kit

Traditional Fixtures & Fittings

Required tools for installation of a V-1020C speaker with V-9914 bridge.

Activity 1.2.3a Airfoil Construction Guide.

Artemide Cosmic Leaf Incasso A A Description -

Step 1：Disassemble battery case

Step 1：Disassemble battery case

Step 1：Disassemble battery case

Step 1：Disassemble battery case

EVERLINE® LED Emergency Drivers

ZUMTOBEL MICROS Q80 1/7,5W LED WN 24V AL Description

Presentation transcript:

Plastic Recessed Kit for Escape Sign Designed by JEWOO R&D Harris Chen 2014.12 Update 2016.3

Escape sign fixture <#>

Recessed kit Spring, use LED down light spring LED & Indicator

ESA10R--- ESA10 with recessed kit Complete product ESA10R--- ESA10 with recessed kit We can supply recessed kit and escape sign separate or complete product . LED & Indicator

ESA08R---ESA08 with recessed kit Complete product ESA08R---ESA08 with recessed kit Same design but smaller size than ESA10 recessed kit, Tooling cost and M/C very close to ESA10 recessed kit.

Installation 1, Cut out hole on ceiling surface. 2, Remove back plate from fixture, make AC supply connection.

Installation 3, Snap fixture into recessed kit. 4, Connect test switch & Indicator and battery.

Installation 5, Assemble back plate on the fixture. 6, Assemble fixture on ceiling surface.

Thank You！！！