Chassis Dynamics Institute

Slides:



Advertisements
Similar presentations
Bus Testing Program Operated by: Thomas D. Larson, Pennsylvania Transportation Institute Altoona Bus Testing and Research Center Pennsylvania Transportation.
Advertisements

STEERING SUSPENSION ALIGNMENT
Team UDFSAE: Suspension Group
Daniel Graves –Project Lead James Reepmeyer – Lead Engineer Brian Smaszcz– Airframe Design Alex Funiciello – Airfoil Design Michael Hardbarger – Control.
Transportation Training Wheel Alignment Why Align the Wheels? Correct Wheel alignment is essential to vehicle safety.  Improve Handling Ability  Maximum.
Suspension Design Case Study
Mike Menos, Michael Caicedo, & Jean-Pierre Sorondo EML 4551 Ethics and Design Project Organization FIU Department of Mechanical & Materials Engineering.
COMBINED HEAT AND POWER (CHP) FOCUS ON DISTRIBUTED GENERATION Stevens Institute of Technology Mechanical Engineering Department Prof. Siva Thangam Supported.
Formula SAE Electro-Pneumatic Shifting System
Palletizing the Easy Way
CHAPTER 14 Wheel Bearings and Service
Suspension Design Analysis Engineering Technology 493 Mechanical Concentration Instructor: Dr. Koutsougeras Advisor: Dr. Ho-Hoon Lee Senior design project.
NATEF Task Area A4 Suspension. Coil Springs and Strut Assemblies  This power point and the corresponding worksheet will help prepare you to remove and.
Department of Mechanical and Aerospace Engineering, The Ohio State University ME 4900 Intro. to Design Studies ME 4902 Motor Sports Competitions ME 4901.
Materials Research Society of Korea Mechatronics Laboratory Geongsang National UniversityMoon Won Ki Performance appraisal of the truck where leaf spring.
FLORIDA INSTITUTE OF TECHNOLOGY COLLEGE OF ENGINEERING
Unclassified U.S. ARMY TANK AUTOMOTIVE RESEARCH, DEVELOPMENT AND ENGINEERING CENTER Reverse Engineering Re-defined Requirements TARDEC 25 AUG Presented.
Institute of Applied Microelectronics and Computer Engineering College of Computer Science and Electrical Engineering, University of Rostock APPLIED VLSI.
Engine Conversion from Combustion to Compressed Air.
Automotive Chassis Systems, 5/e By James D. Halderman Copyright © 2010, 2008, 2004, 2000, 1995 Pearson Education, Inc., Upper Saddle River, NJ All.
Institute of Applied Microelectronics and Computer Engineering College of Computer Science and Electrical Engineering, University of Rostock Slide 1 Spezielle.
Department of Mechanical and Aerospace Engineering, The Ohio State University Student Design Competition Capstone Design (ME 4902) Shawn Midlam-Mohler.
© 2006 PSEN Unit – 3 Inspection & Dynamics The inspection process may seem routine but every trip changes things. Always inspect carefully.
ABET and Automotive Engineering Presented at the SAE Workforce Development Workshop Macomb Community College T. Kenney February 12, 2013.
FSAE – Status Update 2 FSAE 2014.
ME 72 Design What is design?. ME 72 Design What is design? What is a good design? – How do you determine what a good design is?
UXO Model workups 1 CoilSet-6 Bungee / CG suspension Animated Range of motion studies are available at: Bungee1.gif Bungee2.gif Bungee3.gif Bungee4.gif.
Max-Planck- Institut für Plasmaphysik Karsten Liesenberg / AS-T Visit NCSX engineers 11/12 October 2007 Final assembly of Stellarator W7-X in the torus-assembly.
A torsion bar is a spring that is a long, round, hardened steel bar similar to a coil spring except that it is a straight bar. Continued Figure 85–26 A.
Intelligent! Impressive! Incredible!
MECHATRONICS Group # Group Members’ Names MENG 483 Project Title of the Project Spring 20XX.
Chapter 25 Wheel Alignment. Objectives Define the term “wheel alignment” Inspect tires, steering, and suspension systems before alignment Check and adjust.
By : Rohini H M USN : 2VX11LVS19.  This system includes sensors for measuring vehicle speed; steering input; relative displacement of the wheel assembly.
CoCType of commodity required Interior Trim - Cabin space e.g. Pillar trims (Plastic & fabric wrapped or unwrapped) - Rear cabin trim e.g. loadfloor, Loadspace.
Physics and Engineering. Calculus I - Physics I (MAC 2311-PHY 2048)  Success rate*  UCF %  FCS %  Points of Emphasis  Alignment with.
Automotive Engines Theory and Servicing
Overview Definition of an Activity Network Diagram History Basic Terms
Installation Global System
OVERVIEW Impact of Modelling and simulation in Mechatronics system
Vehicle Surfaces Institute
/ / Dr Ben Todd Managing Director / /
Vehicle Electrics Institute
SAE Baja Senior Design Project
Destination CTE Talk to your School Counselor about
CREATING AND SIMULATING FULL VEHICLES
Advanced Suspension Technologies Used in Cars
Online Gifts Buy for wishes happy mother's day to yours choice and with happy gifts find here:
AUTOMATED SESSION PLANNING. In the present world, everything has become automated. By, a click everything is being processed. But the preparation of the.
Dynamics of Learning & Distributed Adaptation James P
Step up to a new model – Trade-In Evaluator
Planning for next Year Technical and Adaptive Challenges May 2014
Project Status Update R09220 – Competitive FSAE Autosports Systems
SAE Baja Senior Design Project
Design & Drafting Technology Unit 6
שילוב קורסים לפיתוח מיומנויות למידה במכללה להנדסה
أنماط الإدارة المدرسية وتفويض السلطة الدكتور أشرف الصايغ
Maintenance Management: THE EMU Experience
Pre-Trip Responsibilities
Peacekeeping and Stability Operations Institute
SAE MINI BAJA PROJECT Suspension Design Analysis
Evaporative Droplet-Particle Collision Dynamics
Energy Planning using Mathematics
Student Design Competition Capstone Design ME 4900, ,
Insert Poster Title here
Automotive Engines Theory and Servicing
Evaluate the integral {image}
Peacekeeping and Stability Operations Institute
CLASS® Compressible Liquid Adaptive Suspension System
Complete Vehicle Systems.
Presentation transcript:

Chassis Dynamics Institute Cole R. Scrogham Presented by The College of Integrated Science & Engineering at James Madison University & Madison Automotive Apprentices (MAAP) Utilize graphic from manual relevant to Institute

Overview Types of Suspension Systems Optimizing for Application Weight Distribution Research and Application

Platform The learning platform for this Institute Adjustments Motorsport Vehicle Adjustments Ride Height Corner Weight Alignment Other: CG, BumpSteer, Spring rate

Timeline Overview of Suspension Types Day 1 Evaluate Motorsport Vehicle on Platen Day 2 Check, Measure, Adjust Day 3 Reporting, Engineer Pre-event, etc Day 4 Timeline May need to adapt to timing

MAAP Overview MAAP Chassis Dynamics Institute Vehicle Electrics MAAP Constituents Surface Finishes Engine Assembly Institute MAAP Overview

Feedback: Privacy Policy Feedback
Do Not Sell My Personal Information
About project: SlidePlayer Terms of Service

© 2025 SlidePlayer.com. Inc. All rights reserved.