NACE SPECIFICATION White Metal Blast Cleaning

Slides:

Advertisements

Similar presentations

The hot dip galvanizing process

Advertisements

Removing Coatings and Cleaning Masonry Substrates

Single Coat 100% Solids Tank Linings SPECIALTY POLYMER COATINGS, INC. Single Coat 100% Solids Tank Linings.

CLEANING AND PAINTING OF STRUCTURAL STEEL THE BASICS

CorroCrush DEMO.

MarineMend Repair Kit Procedure

Calculating Coating Lifetime Costs

Ahead in abrasives. Introduction Eurogrit BV Eurogrit’s head-office in Papendrecht The Netherlands.

Waterjetting—New Standards for Assessing End Condition Cleanliness

SYNTHETIC RED OXIDE METAL PRIMER It has good anti-corrosive properties. It contains Zinc-chrome. Recommended for agricultural, steel structures & other.

Steps to a More Effective Power Tool Cleaning Presented by: Earl Bowry, Jotun Paints, Inc.

Concrete Cleanliness Inspections – Extent of Paint Removal For repaints, verify adequacy of paint removal Definitions for the amount of paint or stain.

Connection Design.

Technical Program: Tanks, Tanks and More Tanks “STEEL WATER STORAGE TANK MAINTENANCE” Maine Water Utilities Association Conference No. 490-April 12, 2007.

Standards, Training, and Certification in the Oil and Gas Industry Presented by: Ernst Toussaint, TransCanada.

Busting The Myths of Wet Abrasive Blasting

Surface Preparation - QA Assessments (con’t)

Regional Sales Manager

Installing Quality Internal Tank Linings: A Perspective David Cushman West Virginia Paint LLC General Manager NACE Certified Coating Inspector #1591 Copyright.

Painting An LNG Tank Important Processes To Follow! Painting An LNG Tank Important Processes to Follow William Donald Director Of Field Operations Tank.

Asset Management Preservation

Applying Coatings over Flash Rust in a Marine Environment

AUZIE QUIC SLIP PTY LTD AQS METAL PRO – 001 INTERIOR AND EXTERIOR.

APPEARANCE OF THE TANK BEFORE THE COATING INSTALLATION OF THE SCAFFOLDINGS.

Engineering Controls for Silica Art Wickman, CIH Georgia Tech Safety & Health Consultation Program.

SIGMACOVER 240. All climates - No winter-grade or tropical versions All industries All substrates All surface preparation standards All specification.

Cleaning Equipment & Methods Chapter 9 Page 97. Basic Cleaning Tools Scrapper Hand Wire Brush Power Brushes Solvent Brush Sand Paper Remove heavy dirt.

Rubbish Hook SECTION: Tools and Equipment ISSUED: REVISED: ##-####

Bending process (Seam joint)

©2008 Sponge-Jet Inc. All rights reserved. 1 Removing Fire Damaged Coatings in Power Plant Mill fire damaged paint on pulverized fuel line Blast area covered.

Use of Field-Applied Fluoropolymer Coatings for Maintenance and Restoration Applications D+D Webinar Bob Parker (AGCCA) June 29, 2011.

Spot Welding. Spot Welding Spot welding is principally used as a method of joining sheet steel. The process is used extensively in the Automobile industry.

Application of Thermal Spray

Paint Removal from CMU and Brick Kenneth A. Trimber KTA-Tator, Inc.

Standards, Training, and Certification in the Wastewater Industry Presented by: Bob Murphy, Sherwin Williams.

Roof Hook SECTION: Tools and Equipment ISSUED: REVISED: ##-####

Horticulture II - Landscape UNIT C LANDSCAPE INSTALLATION AND MAINTENANCE.

Standards, Training, and Certifications in the Marine Coatings Industry Presented by: Earl Bowry.

Sledgehammer SECTION: Tools and Equipment ISSUED: REVISED: ##-####

©2008 Sponge-Jet Inc. All rights reserved. 1 Tank Preparation Chevron Water Softener and Treatment Plant Chevron water softener and treatment tanks that.

1. 2  Surface properties and preparation  Technical characteristics  Process and machine  Materials  Applications 3.

1 DISTEK N.A LLC Introduces: A revolutionary, new environment-friendly space age rust converting paint system Moshe Moked, P.Eng. ERX TM.

Learning Objectives ˗ Specification Components ˗ Consideration of Variables.

The hot dip galvanizing process

UniBond™ ST Polyester-Faced Adhesive Tape

Corrosion Basics Chapter 6 – NACE Book Protective Coatings

Coating Characteristics:

How to Select and Optimize Abrasive Blasting Equipment

Interior of steel tank; 56sqm (600sqft) 50micron (2mil) profile

Inspection of Thermal Spray Coatings

Bright Finished Cold rolled steel sheets

SURFACE PREPARATION BY BLAST-CLEANING

Corrosion Control methods

Why Clean With Sodablasting?

Machining Processes: Cutting

Frosio 16A Standards, specifications & proceduresslide # 1 Standards, specifications and procedures.

Zinc Powder for Coating - Protective Primer on Metal Surfaces Zinc Powder For Coating.

Protective Primer on Metal Surfaces Zinc Dust Paint Grade.

Specification Components Consideration of Variables

Delamination of Coating from a Ship’s Hull

מצוינות ארגונית בקרת תהליך הצביעה

Files Module 5.

Coating Selection for Directional Drill Applications

Bell Ringer Describe the different products you can use to add visual interest to your walls.

Chapter 5 Cleaning the Engine.

Corrosion Control and Monitoring

John Kern SSPC Technical Services Dept.

Corrosion Control and Monitoring

Bob Cloutier, for SSPC Technical Services Dept.

NSRP Joint Project SP&C and WD Panels Robert Cloutier

Presentation transcript:

NACE SPECIFICATION White Metal Blast Cleaning Near White Metal Blast Cleaning Commercial Blast Cleaning Brush-Off Blast Cleaning

SSPC-USA SPECIFICATION (Steel Structure Painting Council) SSPC -1 Solvent Cleaning SSPC -2 Hand Tool Cleaning SSPC -3 Power Tool Cleaning SSPC -4 Flame Cleaning SSPC -5 White Metal Blast Cleaning SSPC -6 Commercial Blast Cleaning SSPC -7 Brush-Off Blast Cleaning SSPC -8 Pickling SSPC -10 Near White Metal SSPC -12 High-and Ultrahigh-Pressure Water Jetting

SS 05 59 00 SWEDISH STANDARD Sa 1 Brush-Off Blast Cleaning Sa 2 Commercial Blast Cleaning Sa 2 ½ Near White Metal Blast Cleaning Sa 3 White Metal Blast Cleaning GRADE FOR POWER TOOL CLEANING St 1 Is consider an un suitable surface for painting St 2 Thorough Cleaning Sa 3 Very Thorough Cleaning

ISO 8501-1 GRADES FOR BLASTING Sa 1 Light Blast Cleaning Sa 2 Thorough Blast Cleaning Sa 2 ½ Very Thorough Blast Cleaning Sa 3 Blast Cleaning to visually clean steel

ISO 8501-1 GRADES FOR RUST (Surface Condition) A Adherent mill scale B Rusty mill scale C Rusted D Pitted and rusted

NACE RP 0274-98 Minimum testing voltage for various coating thickness (mm) (1/32 in) (mils) Testing Voltage 0.51 0.79 13 4.8 1.6 2.4 3.2 4.0 19 16 0.64 1 2 3 4 6 5 20 24 31 10000 7000 6000 94 62 125 156 188 500 625 750 12000 16000 17000 34000 31000 28000 14000