Dressing Dressing Mass (g m-2) Thickness (mm) Number of Layers

Slides:

Advertisements

Similar presentations

and Statistics, 2016, Vol. 4, No. 1, 1-8. doi: /ajams-4-1-1

Advertisements

© The Author(s) Published by Science and Education Publishing.

Table 1. The analytical and physical data for the complexes

Percentage of Polyethylene

Properties Test results

Table 1. Empirical MSE to estimate the CP distribution parameter λ

Perception of discriminatory organizational relationships

Doncaster Wound Care Formulary

Research, 2015, Vol. 3, No. 6, doi: /education

Table 4. Filter Sand Sieve Analysis

© The Author(s) Published by Science and Education Publishing.

Tensile strength (MPa) Length (m) of fibers/kg

Foot-dorsum and plantar

SON Nurse Practitioner Blackboard Community

Tensile Test after Firing

Marshall characteristics

Management Philosophy

© The Author(s) Published by Science and Education Publishing.

Table 2. Levels of youth Involvement in Community Development Programs

in the last evaluation of the software

Table 6. Control sample industry distribution

Table 1. The radial spheroidal functions

Year range Rainfall (mm) ∆s in rainfall Temp (°C) ∆s in temp RH (mm)

Total CO2 Emissions (Electricity + Fossil Fuel)

© The Author(s) Published by Science and Education Publishing.

Table 2. Waste characterization in Port Harcourt, Source [1]

Rating of Water Quality

© The Author(s) Published by Science and Education Publishing.

FSV Interpretation (qualitative)

© The Author(s) Published by Science and Education Publishing.

Number of categories that are mentioned (0% < categories < 5%)

Table 1. Diagnostic methods for systemic fungal infection (n=70)

Table 1. Geometric properties of steel tubes used

Table 2. Modal parameters estimated by Pulse Reflex®

© The Author(s) Published by Science and Education Publishing.

Table 5. Pvalues of ttests for direction a

Entrapment Efficiency (%) ± S.D.

Table 5. Maximum stress, strain and deformation values

© The Author(s) Published by Science and Education Publishing.

Table 1. Characterization Result of Leaded Petrol and Blends

Simulation Frequency(Hz)

Number of questionnaires sent out

© The Author(s) Published by Science and Education Publishing.

Table 6. Pvalues of ttests for direction b

Table 1. Descriptive Statistics

Table 2. Regression statistics for direction a

Table 3. Regression statistics for direction b

Table 2. SUMMARIZED OBSERVATIONS FROM MODEL ANALYSIS

Table 4. Surface roughness (outer faces)

Table 1. Measurements of LEDs

Electrode ν (mm/s) I (A) V (V) HI (J/mm) HI average AWS E309L

Cumulative Percentage

Cumulative Percentage

Control Valve Tag Number

Table 3. Correlation of PC, MC, RC & IC at the Supervisory level

Category Quantity Secondary school 3 Student participant

No. of runs Xo X1 X2 X3 X4 Y1 Y2 Y3 Y4 Y5 Si2

Table 4. Value creation (Y2)

© The Author(s) Published by Science and Education Publishing.

Table 3. Surface roughness (inner faces)

Table 4. Comparison of time-window by emergency gastroscopy

S. No. Product Name yield content

© The Author(s) Published by Science and Education Publishing.

Table 7. The Result of T Test After Treatment

Compressive Strength difference at 1 week (MPa)

Table 6. Twisting moment of counter shaft at different torques

© The Author(s) Published by Science and Education Publishing.

Average Execution Time in seconds

Evaluating questionnaires

Education, 2016, Vol. 4, No. 1, doi: /wjce-4-1-4

Presentation transcript:

Dressing Dressing Mass (g m-2) Thickness (mm) Number of Layers Table 2. Dressing mass, thickness and number of layers Dressing Dressing Mass (g m-2) Thickness (mm) Number of Layers Aquacel® 108±1.2 1.6 1 Kaltostat® 148±4.2 2.0 CarboFlex™ 447±5.9 3.9 5 Melolin* 268±3.3 3.4 3 CliniSorb® 260±2.0 1.2 Versiva® XC® 1040±12.2 2.5 Mepilex®Border 828±7.2 4.2 Allevyn Gentle Border 723±3.3 Mepilex® 696±1.1 5.9 Mepilex® lite 384±0.9 Aquacel® Surgical 1128±3.5 2 CombiDERM® 633±2.1 1.8 Biatain 988±2.2 M. Uzun et al. In Vitro Characterisation and Evaluation of Different Types of Wound Dressing Materials. Journal of Biomedical Engineering and Technology, 2013, Vol. 1, No. 1, 1-7. doi:10.12691/jbet-1-1-1 © The Author(s) 2013. Published by Science and Education Publishing.