CHAPTER 9: Definitions A. Solid Solution Consists of atoms of at least 2 different types Solute (minority) and Solvent (majority) Substitutional vs. Interstitial Components vs. System Components – pure metals or compounds that compose an alloy System – series of possible alloys of different composition
B. Solubility Limit • Maximum concentration of solute atoms that may dissolve • Ex: Phase Diagram: Water-Sugar System Question: What is the solubility limit at 20C? Answer: 65wt% sugar. If Co < 65wt% sugar: solution If Co > 65wt% sugar: syrup + sugar. • Solubility limit increases with T: e.g., if T = 100C, solubility limit = 80wt% sugar.
C. Phase • A homogeneous portion with uniform physical and chemical characteristics Every pure metal, every liquid, solid and gaseous solution Note: Different phases may be different physically, chemically or both. For polymorphic substance, each structure is a phase. Aluminum- Copper Alloy
D. Equilibrium E. Phase Equilibrium At a specified condition (temperature, pressure and composition), free energy (internal energy & entropy) is minimum. E. Phase Equilibrium Constant phase characteristics In solids, rate of approach to equilibrium is extremely slow; sometimes take metastable state.
Equilibrium Phase Diagram Represent relationship between temperature, and composition and quantities of phases at equilibrium. Assume: P is constant Variables are T and composition Only binary alloys (2 components)
Isomorphous System • Copper-Nickel System isomorphous because of complete solid solution solubility horizontal – composition; vertical – temperature 3 Regions: Alpha () phase – FCC solid solution below 1080C, complete solubility Liquid (L) phase – liquid solution Two-phase ( + L) region Liquidus line – separates L and + L Solidus line – separates and + L Intersection of lines – melting point of pure metal (one temperature) Melting of solution: happens over a range of T’s.
A. Finding phases present Given know T and Co, locate T-Co point on the graph. • Examples: A(60,1100): 1 phase: B(35,1250): 2 phases: L + Cu-Ni phase diagram
B. Finding composition of phases i) one phase – same as overall composition ii) two-phase : - Construct a tie line (isotherm, horizontal) - Intersection of tie line with phase boundaries • Examples: Cu-Ni system
C. Phase amounts (mass/weight fraction of each phase) i) single phase – 100% ii) 2-phase: Lever Rule Cu-Ni system • Examples: CO = 35 wt% Ni At TA: L only WL=1.0 or 100% At TD: only W=1.0 or 100% At TB: + L Use Lever Rule = 0.27
Lever Rule • A geometric interpretation:
Microstructural Development: Isomorphous • Phase diagram: Cu-Ni system. Cu-Ni system • System is: --binary --isomorphous i.e., complete solubility of one component in another; a phase field extends from 0 to 100wt% Ni. • Consider Co = 35wt%Ni. Start at A and cool slowly (equilibrium cooling) Follow development of microstructures
Non-equilibrium solidification • Ca changes as we solidify. • Cu-Ni case: First a to solidify has Ca = 46wt%Ni. Last a to solidify has Ca = 35wt%Ni. • Fast rate of cooling: Cored structure • Slow rate of cooling: Equilibrium structure
MECHANICAL PROPERTIES: Cu-Ni System • Effect of solid solution strengthening on: --Tensile strength (TS) --Ductility (%EL,%AR) Adapted from Fig. 9.5(a), Callister 6e. Adapted from Fig. 9.5(b), Callister 6e. --Peak as a function of Co --Min. as a function of Co
BINARY-EUTECTIC SYSTEMS limited solid solution solubility has a special composition with min. melting temp. Cu-Ag system Solvus line – separates + from , and + from Eutectic Point, E – an invariant pt (3 phases in equilibriium): CE = 71.9wt% Ag, TE = 779ºC
EX: Pb-Sn (Eutectic) TE = 183ºC CE = 61.9 wt% Sn
EX: Pb-Sn Eutectic • For a 40wt%Sn-60wt%Pb alloy at 150C, find... a) the phases present: a + b b) the compositions of the phases: Ca = 11wt%Sn Cb = 99wt%Sn c) the relative amounts of each phase: Pb-Sn system W= (99-40)/(99-11) = 59/88=0.67 W= (40-11)/(99-11) = 29/88=0.33
Microstructures: Eutectic A. Co < 2wt%Sn • Result: - polycrystal of a grains. Adapted from Fig. 9.9, Callister 6e.
Microstructures: Eutectic B. 2wt%Sn < Co < 18.3wt%Sn • Result: --grains of a crystal with fine b crystals. Pb-Sn system Adapted from Fig. 9.10, Callister 6e.
Microstructures: Eutectic Co = CE As we cross TE, Eutectic reaction: L (61.9%) (18.3%) + (97.8%) • Result: Eutectic microstructure -alternating layers of a and b crystals (short dist. to diffuse). Pb-Sn system Adapted from Fig. 9.11, Callister 6e.
Microstructures: Eutectic • 18.3wt%Sn < Co < 61.9wt%Sn • Result: primary a and a eutectic microstructure Pb-Sn system Question: What are the relative amounts of primary and eutectic ?
HYPOEUTECTIC & HYPEREUTECTIC Adapted from Fig. 9.7, Callister 6e. (Fig. 9.7 adapted from Binary Phase Diagrams, 2nd ed., Vol. 3, T.B. Massalski (Editor-in-Chief), ASM International, Materials Park, OH, 1990.) (Figs. 9.12 and 9.15 from Metals Handbook, 9th ed., Vol. 9, Metallography and Microstructures, American Society for Metals, Materials Park, OH, 1985.) Adapted from Fig. 9.15, Callister 6e. Adapted from Fig. 9.15, Callister 6e. (Illustration only) Adapted from Fig. 9.12, Callister 6e. Differentiate: components vs. phases vs. microconstituents
Other Invariant Points: Eutectoid – (“eutectic like”): solid1 solid2 +solid3 Peritectic: solid1 + L solid2
The Iron-Carbon System
The Iron-Carbon System Iron – iron carbide phase diagram: iron rich (0-6.7 wt% C) i. pure iron: ferrite, -iron: BCC austenite, -iron: FCC -ferrte: BCC ii. 6.7 wt% C: compound – iron carbide, or cementite (Fe3C) Cementite – Fe3C Very hard and brittle Metastable only but will remain indefinitely at room T iii. Singe-phase solid solutions – C is an interstitial impurity and : BCC – very limited solubility (max solubility = 0.022 wt%C) : FCC – higher solubility limit (2.11 wt%C) Why does BCC have lower solubility than FCC? iv. Two-Phase Regions: Eutectic Point at 4.3 wt% C and 1147C Eutectoid Point at 0.76 wt%C and 727C
IRON-CARBON (Fe-C) PHASE DIAGRAM (Adapted from Fig. 9.24, Callister 6e. (Fig. 9.24 from Metals Handbook, 9th ed., Vol. 9, Metallography and Microstructures, American Society for Metals, Materials Park, OH, 1985.) Adapted from Fig. 9.21,Callister 6e. (Fig. 9.21 adapted from Binary Alloy Phase Diagrams, 2nd ed., Vol. 1, T.B. Massalski (Ed.-in-Chief), ASM International, Materials Park, OH, 1990.)
HYPOEUTECTOID STEEL Adapted from Figs. 9.21 and 9.26,Callister 6e. (Fig. 9.21 adapted from Binary Alloy Phase Diagrams, 2nd ed., Vol. 1, T.B. Massalski (Ed.-in-Chief), ASM International, Materials Park, OH, 1990.) Adapted from Fig. 9.27,Callister 6e. (Fig. 9.27 courtesy Republic Steel Corporation.)
HYPEREUTECTOID STEEL Adapted from Figs. 9.21 and 9.29,Callister 6e. (Fig. 9.21 adapted from Binary Alloy Phase Diagrams, 2nd ed., Vol. 1, T.B. Massalski (Ed.-in-Chief), ASM International, Materials Park, OH, 1990.) Adapted from Fig. 9.30,Callister 6e. (Fig. 9.30 copyright 1971 by United States Steel Corporation.)
ALLOYING STEEL WITH MORE ELEMENTS • Teutectoid changes: • Ceutectoid changes: Adapted from Fig. 9.31,Callister 6e. (Fig. 9.31 from Edgar C. Bain, Functions of the Alloying Elements in Steel, American Society for Metals, 1939, p. 127.) Adapted from Fig. 9.32,Callister 6e. (Fig. 9.32 from Edgar C. Bain, Functions of the Alloying Elements in Steel, American Society for Metals, 1939, p. 127.)
Example. For a 0.35 wt%C steel at just below 727 ºC, determine: Fraction of total cementite and ferrite Fraction of proeutectoid ferrite and pearlite Fraction of eutectoid ferrite Answers: a) W=0.95, Wcementite=0.05, b) W’=0.56, Wp=0.44 c) We=0.39
It’s Clicker Time! A reaction wherein, upon cooling, a solid phase and a liquid phase transform isothermally and reversibly to another solid phase having a different composition is a) eutectic b) eutectoid c) peritectic d) proeutectoid
2. Proeutectoid -ferrite forms during the transformation of austenite a) above the eutectoid temperature in a hypoeutectoid steel b) above the eutectoid temperature in a hypereutectoid steel c) below the eutectoid temperature in a hypoeutectoid steel d) below the eutectoid temperature in a hypereutectoid steel
3. The line separating a one-phase solid region from a two-solid region is called a) isomorphous b) solidus c) solvus d) liquidus
4. Which of the following is/are true about an isomorphous system? I. The is only one solid phase. II. The phase diagram has no solvus line. III. There is at least two two-phase regions. IV. The phase diagram has a euctectic point. a) I and II b) I only c) I and III d) II and IV
5. For the equilibrium phase diagram of the iron-iron carbide system, which of the following solid solutions has the highest solubility limit? a) BCC delta ferrite b) FCC gamma austenite c) BCC alpha ferrite d) cementite
6. A Cu-Ag alloy of composition 80 wt% Ag is cooled from a temperature of 1200C. What is the approximate composition of the first solid that forms? a) 8.0 wt% Ag b) 71.9 wt% Ag c) 91.2 wt% Ag d) 93.0 wt% Ag
7. A Cu-Ag alloy of composition 40 wt% Ag undergoes equilibrium cooling from a temperature of 1200C. What is the approximate composition of the last liquid to solidify? a) 8.0 wt% Ag b) 71.9 wt% Ag c) 91.2 wt% Ag d) 93.0 wt% Ag
8. A hypoeutectic Cu-Ag alloy of wt% Ag undergoes equilibrium cooling from a temperature of 1200C. Which of the following microconstituents will be present at room temperature. a) only alternating layers of alpha and beta. b) primary alpha and primary beta c) primary alpha plus eutectic alpha and beta d) primary beta plus