Question/Quality check

Slides:

Advertisements

Similar presentations

Objective Use agricultural mechanics tools properly and safely.

Advertisements

Coat Hook Revision Notes

CORDLESS DRILL WHAT IS IT ? WHAT IS IT USED FOR ? click here

Drills & Drilling Drills & Drilling.

Mechanical Workshop Module 6: Drilling.

Mechanical Workshop Module 6

Cutting Machines Foldable Information. DRILL PRESS Related Terms  Center punch  Cutting Oil.

Research & Development Machine Safety Information.

Technology Education Shop and lab safety Band Saw Scroll Saw

TOOL: Radial Arm Saw NEXT STEP: Radial Arm Saw RESULTS: Finish Top Apron Pieces at 9” L x 4” W x ¾ “ Th PROJECT Square Plant Stand PART Top Apron # NEEDED.

Tool Safety. Rule #1 – Do Not Fall On Your Drill.

Tray Tools, Materials & Processes. The Pillar Drill can be used to drill wood, metal, and plastic. As a general rule the larger the hole you are trying.

Overall Project Objectives You will develop your marking out skills. You will develop your ability to read and follow working drawings Master the use.

2.1. INTRODUCTION Safety should be uppermost in the minds of all machine technology workers. It should become a state of mind so that reactions become.

Specification section 3.8

PLAN #PartProcessTools and equipmentQuality controlSafety *Aprons must be worn is ALL stages of manufacture Tim e 1 MDF base Mark out on MDF piece Pencil,

Production Tools in Technology

Basic Tool Safety and Equipment

What is a machining Process? Machining is the manufacturing process by which parts can be produced to the desired dimensions and surface finish from a.

Planning Manufacture TaskEquipmentQC/QA Mark out the shape of the speaker front and back Tri square, pencil, ruler, tape measure.

Intro to Power Tools Ag Mech I Class Notes. Objectives AM15.01 Explain how power tools are used in agricultural mechanics. AM15.02 Know and demonstrate.

Proper Use of Agricultural Mechanics Power Tools

F. 1 Design and Technology

Module-6 Drilling.

Production Lab Safety By :Patrick Wiswell Sept 25/05.

BRX210 ‘Mechanical Blueprint Reading’ Unit #13 Print Reading Review.

Safety in the Machine Shop Session 1. Shop Tools and Techniques2.

Objective 2.01 Recognize safety procedures and practices in a technological world.

General Safety Foundations of Engineering and Technology I.

WOOD MATERIALS TECHNOLOGY 4 th Edition. Chapter 22 Machines.

Homework: Use the information that you gathered this week to draw out your plan view working drawing, 1:1 scale. Use sheet 6. Hand in next week. Start.

Principles of Manufacturing Safety is no Accident Copyright © Texas Education Agency, All rights reserved.

General Safety Foundations of Engineering and Technology.

GCSE Resistant Materials Tools and Equipment

Cabinetwork - Specialised Module 3 Equipment, Tools and Machines.

BETHS PENCIL BOX. This is a pictures of my 250 mm piece of wood This is my piece of wood cut half way and I am about to chisel it!

Workshop Safety 1. Do not enter or leave the workshop without the teacher ’ s approval.

KS4 Graphic Products.  Describe the process of block modelling of MDF & Styrofoam and rapid prototyping using stereolithography (SLA) and 3D printing.

Yasmin Yassin 7F.  PAGE 1: Index  PAGE 2:7 Design Idea’s  PAGE 3:4 Design Idea’s  PAGE 4:Final Design  PAGE 5 :Design Brief  PAGE 6:Finished Pencil.

Used for cutting wood and plastic

Year 7 Homework Tasks Year 8 Homework Tasks Year 9 Homework Tasks

Mood Sheet Project Title: ??????? Task:

Inspection of stock materials for defects

General & Machine Safety Notes

Centre Name: Royal Hospital School

Research & Development

Year 7 RM Wood Belt Sander

Proper Use of Agricultural Mechanics Power Tools

Year 10 CDT Workshop Tool Book

RESISTANT MATERIALS REVISION Tools + Equipment Health + SAFETY ISSUES

Portable Power Tools Cordless Drill Hammer Drill Orbital Sander

Mood Sheet Project Title: ??????? Task:

The Application of….

Manufacturing Processes

St Andrews High School Shaping Wood.

Industrial Technology Timber Stage 5

Safety in the workshop!! (All Technology Classes)

Junior cycle wood technology Tomás callanan

A2 Coursework - Making EdExcel.

Drills & Drilling Drills & Drilling.

Portable Power Tools Cordless Drill Hammer Drill Orbital Sander

Foundations of Engineering and Technology I

Remember you can revise at home!

Design & Technology Department.

Wood shop safety.

Hand Tools Commonly Asked Questions

8 8 clock clock Year 8 Resistant Materials- Prep Work

Tolerance Tolerance is the amount of error that is allowed when manufacturing a product. Very small differences are allowed in products because different.

The CO2 Dragster TIJ 101 Upon finishing your brainstorming and Final Drawing (with dimensions and ruled lines) The following steps with be taken for fabrication.

Presentation transcript:

Question/Quality check Production plan Create a flow chart to describe the manufacture of your lamp. You must try to use all of the shapes available. Start/Finish Question/Quality check Process/Step Predicted Time Changes/ modifications

Manufacturing diary Stage Materials Used Tools/ equipment, processes Safety Procedures How will Quality Control/ tolerance tests be carried out Reviewing quality control/ tolerance tests Manufacturing the base of the lamp MDF Metal Rule, fret saw, belt sander, glass paper, hole saw, pillar The fret saw, pillar drill and belt sander are dangerous workshop machines. When using them I wore goggles and an apron and only used them after having proper training. I made sure I had no loose items that could get caught in the belt sander or pillar drill. The hole that has been cut must be within +/- 1mm of the desired diameter and will be checked with a calliper. The base must be checked for smooth finishing that will give no splinters. The hole cut had a 21mm diameter which is +1mm larger than the desired hole, therefore the hole is reasonable in quality. The base was perfectly smooth and has no sharp edges or possible splinters.

Tools/ equipment, processes Safety Procedures Stage Materials Used Tools/ equipment, processes Safety Procedures How will Quality Control/ tolerance tests be carried out Reviewing quality control/ tolerance tests Manufacturing the base of the lamp MDF Metal Rule, fret saw, belt sander, glass paper, hole saw, pillar The fret saw, pillar drill and belt sander are dangerous workshop machines. When using them I wore goggles and an apron and only used them after having proper training. I made sure I had no loose items that could get caught in the belt sander or pillar drill. The hole that has been cut must be within +/- 1mm of the desired diameter and will be checked with a calliper. The base must be checked for smooth finishing that will give no splinters. The hole cut had a 21mm diameter which is +1mm larger than the desired hole, therefore the hole is reasonable in quality. The base was perfectly smooth and has no sharp edges or possible splinters.

Final ? (product images from all different views) Problems During making/planning Solutions/Changes made. Final ? (product images from all different views)

Final ? (product images from all different views) Problems During making/planning Solutions/Changes made. Final ? (product images from all different views)