Under the Guidance of Submitted by Project Title POWER SAVER FOR INDUSTRIES & COMMERCIAL ESTABLISHMENTS Under the Guidance of Submitted by

ABSTARCT Power factor is defined as the ratio of real power to apparent power. Where real power is the time integral of the instantaneous power measured over a full period and the apparent power is simply the product of the RMS voltage and RMS current measured over the entire period. The time lag between the zero voltage pulse and zero current pulse duly generated by suitable operational amplifier circuits are fed to two interrupt pins of the microcontroller where the program takes over to actuate appropriate number of relays at its output for bringing shunt capacitors into the load circuit to get the power factor till it reaches 0.95.

PROJECT BLOCK DIAGRAM

HARDWARE COMPONENTS MICROCONTROLLER (AT89S52/AT89C51) RELAY RELAY DRIVER LCD LM339 CURRENT TRANSFORMER INDUCTIVE LOAD SHUNT CAPACITOR PUSH BUTTONS LED 1N4007 / 1N4148 RESISTOR CAPACITOR

POWER SUPPLY Bridge rectifier 5v Regulator 230 V AC 50 Hz 5V DC Filter(470µf) 12V step down transformer

It is a smaller computer Has on-chip RAM, ROM, I/O ports... MICROCONTROLLER It is a smaller computer Has on-chip RAM, ROM, I/O ports... RAM ROM I/O Port Timer Serial COM Port Microcontroller CPU A single chip

INTERNAL STRUCTURE OF A MICRO CONTROLLER-AT89S52/51 CPU On-chip RAM On-chip ROM for program code 4 I/O Ports Timer 0 Serial Port OSC Interrupt Control External interrupts Timer 1 Timer/Counter Bus Control TxD RxD P0 P1 P2 P3 Address/Data Counter Inputs

Features of AT89S51/52 Compatible with MCS®-51 Products 8K Bytes of In-System Programmable (ISP) Flash Memory Endurance: 10,000 Write/Erase Cycles 4.0V to 5.5V Operating Range Fully Static Operation: 0 Hz to 33 MHz 256 x 8-bit Internal RAM 32 Programmable I/O Lines Three 16-bit Timer/Counters Eight Interrupt Sources Full Duplex UART Serial Channel Interrupt Recovery from Power-down Mode Watchdog Timer Dual Data Pointer

Pin Description

RELAY IT IS A ELECTRO MAGNETIC SWITCH USED TO CONTROL THE ELECTRICAL DEVICES COPPER CORE MAGNETIC FLUX PLAYS MAIN ROLE HERE

The relay's switch connections are usually labeled COM, NC and NO: COM = Common, always connect to this; it is the moving part of the itch. NC = Normally Closed, COM is connected to this when the relay coil is off. NO = Normally Open, COM is connected to this when the relay coil is on

RELAY DRIVER (ULN 2003) ULN2003 is a high voltage and high current Darlington transistor array It consists of seven NPN Darlington pairs that feature high-voltage outputs with common-cathode Clamp diode for switching inductive loads. The ULN2003 has a 2.7kW series base resistor for each Darlington pair for operation directly with TTL or 5V CMOS devices. Current, Output Max:500mA Voltage, Input Max:5V Voltage, Output Max:50V

Fig: ULN 2003

QUAD VOLTAGE COMPARATOR LM339 FEATURES ● Wide single supply voltage range 2.0VDC TO 36VDC or dual supplies ±1.0VDC to ±18VDC ● Very low supply current drain (0.8㎃) independent of supply voltage (1.0㎽/comparator at 5.0VDC) ● Low input biasing current 25㎁ ● Low input offset current ±5㎁ and offset voltage ● Input common-mode voltage range includes ground ● Differential input voltage range equal to the power supply voltage ● Low output 250㎷ at 4㎃ saturation voltage ● Output voltage compatible with TTL, DTL, ECL, MOS and CMOS logic system ● Moisture Sensitivity Level 3

LIQUID CRYSTAL DISPLAY (LCD) Most common LCDs connected to the microcontrollers are 16x2 and 20x2 displays. This means 16 characters per line by 2 lines and 20 characters per line by 2 lines, respectively. The standard is referred to as HD44780U, which refers to the controller chip which receives data from an external source (and communicates directly with the LCD.

If an 8-bit data bus is used the LCD will require 11 data lines LCD BACKGROUND If an 8-bit data bus is used the LCD will require 11 data lines (3 control lines plus the 8 lines for the data bus) The three control lines are referred to as EN, RS, and RW EN=Enable (used to tell the LCD that you are sending it data) RS=Register Select (When RS is low (0), data is treated as a command) (When RS is High(1), data being sent is text data ) R/W=Read/Write (When RW is low (0), the data written to the LCD) (When RW is low (0), the data reading to the LCD)

Soft ware Requirements Keil an ARM Company makes C compilers, macro assemblers, real-time kernels, debuggers, simulators, integrated environments, evaluation boards, and emulators for ARM7/ARM9/Cortex-M3, XC16x/C16x/ST10, 251, and 8051 MCU families. Compilers are programs used to convert a High Level Language to object code. Desktop compilers produce an output object code for the underlying microprocessor, but not for other microprocessors.

i.e the programs written in one of the HLL like ‘C’ will compile the code to run on the system for a particular processor like x86 (underlying microprocessor in the computer). For example compilers for Dos platform is different from the Compilers for Unix platform  So if one wants to define a compiler then compiler is a program that translates source code into object code.

QUERIES ?

THANKYOU