Eric building the fin mount.

Slides:

Advertisements

Similar presentations

UF Hybrid Rocket Teams Mile High Club Brought to you by Chris Leonard, Ty Morton, Sam Darr, and Josh Childs.

Advertisements

BYU Rocket Team Special thanks to:

Water Rockets!.

Battery PDB Controller GPS Data Recorder Antenna Cam Lower Stage Harness Upper portLower port Upper port Lower Stage Harness Sensors Cam Avionics Layout.

HOW TO MAKE A ROCKET BY SAM CANNINGTON. THE FUSELAGE 1.Cut out a thin peace of cardboard.

How to Make a PAPER TIGER. STEP 1: MAKE BODY TUBE 1. Use a spent engine to roll your body tube out of copier paper the short way 2. Test the size by sticking.

How to Make a Model Rocket

Critical Design Review NASA University Student Launch Initiative University of Nebraska–Lincoln

Launch Lug – helps to guide the rocket upward until it reaches enough velocity for the fins to engage. Parachute – assists in the safe recovery of the.

Bottle Rockets! 8th grade final project.

Model Rocketry Mr. Capella Technology Education. Parts of a Model Rocket n Nose cone n Body tube n Fins n Launch lug

The Estes Viking Rocket

Northwest Indian College Space Center First Nations Launch 4/29/10 – 5/2/10.

Building A Model Rocket

Model Rocketry 8th Grade Technology Transportation Unit Eric Wasacz Thomas Rozelle Kenny Bouwens Eric Wasacz Thomas Rozelle Kenny Bouwens.

CDR Clear Lake's Team Rocket 2929 Bay Area Blvd. Houston, TX

Model Rocketry. Parts of a Model Rocket Rocket Engines Most are single use engines. Classified by the amount of power they produce.

Rockets Read and follow along. On your journals, draw the rockets and label. Draw and label the parts of the rockets and answer the questions listed.

Team Members:Tony Guzzo Eric Jacob Bill Liewehr Alex Schlaupitz Design of a Level 2 Rocket for the Wisconsin Space Grant Consortium Advisor: Dr. William.

Govt. Girls Higher Secondary School , Pattom , Trivandrum.

Rocket Research History Scientific Research Modern Applications Roxboro Road Middle School Mr. Clayton and Mrs. Zajac.

Rocketeering Sub-space Flight Made Easy. History of Rocket Technology  First occurrence in recorded history places rockets in China during the third.

Rocketry ‘06 Carl Sandburg College Upward Bound Summer Program.

Composite Rockets. Rocket Design The rocket should be designed and tested in a rocket simulation software. Rocket should then be modeled in Autodesk Inventor.

Science Fiction. Rocket flight Centre of Mass or Centre of Gravity (CM or CG) Centre of mass is the mean or central location of all the mass of an object.

The Rocket Men Project One Giant Leap. Final Launch Vehicle Dimensions Rocket Length in. Rocket Mass- 171 oz. Top Body Tube Length in. Bottom.

FRR Presentation IF AT FIRST YOU DON’T SUCCEED, TRY AGAIN… AND AGAIN AND AGAIN AND AGAIN.

TARCkan Nasir Almasri Audrey Kelly Kari Schulz. Overview Problem Statement Timeline Background Scope Brainstorming & Research Criteria Constraints Explore.

Flight Readiness Review Student Launch Initiative SCS Rocket Team Statesville Christian School April 2, 2008.

TARCkan Nasir Almasri Audrey Kelly Kari Schulz. Overview Problem Statement Timeline Background Scope Brainstorming & Research Criteria Constraints Explore.

Making a Home Made Estes Rocket By Roberto & Stefano Barbier.

Brain Surgery and Rocket Science By Howard Botting and Benjamin Mitchell.

History Of Water Rockets ● The first water rocket I could find record of was made of tin cans. ● Soda pop bottles caused a big growth spurt in popularity.

Explorer Post 1010 TARC Team Rockville, Maryland Team America Rocketry Challenge Final Fly-Off Presentation May 12, 2012.

UCF USLI Organization Team Development Proposal Requirements September 17 th, 2009.

Neelam Patel David Wade Brian Reyes TITLE IN PROGRESS.

The Rocket Men Project One Giant Leap. Dimensions Rocket Length in. Rocket Mass- 171 oz. Top Body Tube Length in. Bottom Body Tube Length-

Rockets !. Robert H. Goddard, Ph.D. (Oct. 5, Aug. 10, 1945) A U.S. professor and scientist, he was a pioneer of controlled, liquid-fueled rocketry.

Model Rocketry Saturn Phase

Rocket Launch. Launch Area Minimum launch areas Launch Configuration Launcher upwind of landing zone Spotters at right angles Spotters will measure angle.

Neelam Patel Brian Reyes David Wade ????? Mystery Member ????? STATUS UPDATE TEAM ALPHA.

R OCKET S IMULATORS By Howard Smart. C ONTENTS Introduction to Rockets Introduction to Rocket Simulators An introduction to each simulator and how they.

Egg Carrying Rocket Complete Your goal is to have your rocket looking something like this at the end of this section– fins attached and rocket engine block.

Rocket Project: Newton’s 3 Laws in 3D!.

Physics 11 Rocket Design Day Mr. Jean. The plan: Video clip of the day Rocket Designs and builds.

Preliminary Design Review Clear Lake High School Team Rocket.

Air Powered Rocket. Rocket Body Lay two pieces of paper with their long sides over lapping Tape the paper together Roll the paper into a tube using the.

prepared by Mr.Grad©2004 Today you are going to start the assembly of your rocket, which you will launch at a later date.

Space Exploration & Rocketry Power and Transportation Technology By: Mr. Smith.

Rockets August 10, 2010 SUNRISE-CREST Camp 2010.

Water Rockets Garrek, Angus and Jacob. Introduction Names Video From Gaggletube showing a small water rocket being launched.

Warm-Up 4/26/17 Take notes on what I say is important.

College of Engineering

* 07/16/96 Propulsion Lab 6 Winter Quarter *.

Nasir Almasri Audrey Kelly Kari Schulz

Rocket Science! Mr McGregor Part 1.

Rocket Launch Aerospace Engineering © 2011 Project Lead The Way, Inc.

Mr. Capella Technology Education

بسم الله الرحمن الرحيم الموضوع:الوضوء صفته وفرائضه وسننه

Model Rockets Nose and Parachute Assembly.

Materials included Engine Wood glue plastic cement clear tape masking tape spray paint xacto knives sand paper etc,etc,etc…

LESSON LD02 The Model Rocket

Final Readiness Review

Bottle Rocket Construction

LESSON LD02 The Model Rocket

Materials included Engine Wood glue plastic cement clear tape masking tape spray paint xacto knives sand paper etc,etc,etc…

Dual-Deploy Launch Checklist

Materials included Engine Wood glue plastic cement clear tape masking tape spray paint xacto knives sand paper etc,etc,etc…

Single-Deploy Launch Checklist

Presentation transcript:

Eric building the fin mount.

Brenton gluing the body tube.

Eric attaching the fin mount to the body tube.

Eric gluing the shock cord mount.

Brenton installing the shock cord.

Brenton attaching the shock cord & parachute to the nose cone.

Eric installing the assembled nose cone with the attached parachute and shock cord into the body tube with three squares of recovery wadding.

Max relaxing.

Eric putting in the igniter for the engine (after engine was installed Max

Brenton assembling the launch pad.

Eric placing the rocket on the launch pad.

Brenton decorating the rocket.

The completed rocket and its builders.