JN0-661 DumpsJN0-661 Exam DumpsJN0-661 dumps pdfJN0-661 braindumps JN0-661 Dumps PDF Service Provider Routing and Switching
This exam replaced the JN0-660 exam in July. Looking that blueprints, the major changes I saw were: Addition of EVPNs in Layer 2 VPN section Removal of automation topics Even the preparation materials suggested by the JNCP team are identical for both exams with the exception of a book for EVPNs. Service Provider Routing and Switching JN0-661 DumpsJN0-661 Exam DumpsJN0-661 dumps pdfJN0-661 braindumps
The learning and preparation process: My day to day job involves neither MPLS/VPNs nor Junos (although I do keep up with MPLS/VPNs on a regular basis) so I had to give myself enough time to refresh all the material and possibly perform detailed labs on my weakest topics. All in all, I dedicated the last 3 months entirely to JNCIP-SP studies. I created a small SP network of 6 vSRXs with 1 vSRX split into multiple VRs acting as CEs. In the end, the only topics I performed labs on were MPLS/VPNs (All flavors including L2, L3, EVPN, MVPN, VPLS and Hierarchical L3 VPNs), BGP and CoS. Finally, here is the material I used in roughly the order of most used to least used: JN0-661 DumpsJN0-661 Exam DumpsJN0-661 dumps pdfJN0-661 braindumps
JNCIP-SP Exam Objectives (Exam: JN0-661) This list provides a general view of the skill set required to successfully complete the specified certification exam. OSPF IP Multicast Advanced MPLSIS-IS Layer 2 VPNs BGP Class of Service (CoS) Layer 3 VPNs JN0-661 DumpsJN0-661 Exam DumpsJN0-661 dumps pdfJN0-661 braindumps
DEMO QUESTIONS JN0-661 DumpsJN0-661 Exam DumpsJN0-661 dumps pdfJN0-661 braindumps You are configuring a Layer 2 circuit. Which two configuration steps are required? (Choose two.) Options A. Configure LDP on the interfaces between PE and CE routers. B. Configure circuit or translational cross-connects between PE routers and between PE and P routers. C. Configure circuit or translational cross-connects between PE and CE routers. D. Configure LDP on the interfaces between PE routers and between PE and P routers. Answer: C,D Question 1
JN0-661 DumpsJN0-661 Exam DumpsJN0-661 dumps pdfJN0-661 braindumps You have recently deployed an MPLS network using CSPF with its default settings. Which statement is true regarding path selection when multiple candidate paths exist? Options A. The path selected will be based on the most-fill bandwidth ratio. B. The path selected will be based on the least-fill bandwidth ratio. C. The path selected will be based on a randomized algorithm. D. The path selected will be based on the first-hop LSR's RID. Answer: C Question 2
JN0-661 DumpsJN0-661 Exam DumpsJN0-661 dumps pdfJN0-661 braindumps You are asked to provision a BGP-signaled Layer 2 VPN for a new customer. What information is required for the VPN routing instance that is connected to the CE device? (Choose three.) Options A. the logical interfaces provisioned to the local CE device B. the logical interfaces provisioned to the remote PE device C. the Layer 2 encapsulation type D. the local site ID E. the circuit identifier Answer: A,C,D Question 3
JN0-661 DumpsJN0-661 Exam DumpsJN0-661 dumps pdfJN0-661 braindumps An MX Series router has received a BGP prefix from its peer. There are multiple destination routes to the BGP prefix with the default BGP route preference. In this scenario, what is the first tie-breaker used to select the destination route? Options A. lowest MED B. shortest cluster list length C. highest local preference D. lowest origin code Answer: C Question 5
JN0-661 DumpsJN0-661 Exam DumpsJN0-661 dumps pdfJN0-661 braindumps What are two characteristics of L2 circuits? (Choose two.) Options A. Routing instance configuration is required for L2 circuits to function correctly. B. Routing instance configuration is not required for L2 circuits to function correctly. C. BGP is required for L2 circuits to function correctly. D. BGP is not required for L2 circuits to function correctly. Answer: B,D Question 4
JN0-661 DumpsJN0-661 Exam DumpsJN0-661 dumps pdfJN0-661 braindumps