STAiR Creation By Steven Adler NEXT A voltage drop is the representation of energy used over a load device or resistance device in a circuit. If all.

Slides:

Advertisements

Similar presentations

Internal Resistance.

Advertisements

S2 Electricity and circuits Revision Quiz To begin click the button below.

Circuits Energy & Environment. Simple Circuit G -ve +ve Wire Lamp Switch Fuse Battery Power Source Safety Device Controlling Device Purpose Connect circuit.

Register Digital Multimeter Usage Click Register to begin the course.

Cells have positive and negative electrodes.

BASIC ELECTRICITY n VOLTAGE n AMPERAGE n OHMS Page 242Autobody Text.

Science 9 Electricity Review Ohm’s Law Circuits.

Using a DVOM (Digital Volt Ohm Meter)

Chapter 7. Voltage Remember: Atoms are in EVERYTHING and they are made up of equal amounts of positive and negative charges. Battery: uses chemical energy.

xc.  Ohm’s Law explains the relationship between voltage (V or E), current (I) and resistance (R)  Used by.

Ohm’s Law Review. Division Review 15 ÷ ÷ ÷ 2.3.

Electricity Foundations of Physics. Electricity The movement of charge from one place to another Requires energy to move the charge Also requires conductors.

Copyright © 2008 Pearson Education, Inc., publishing as Pearson Addison-Wesley Electricity Physics 102 Goderya Chapter(s): 22 and 23 Learning Outcomes:

Electricity and Electrical Circuits. Chapter Sections O 1 - Electrical Circuits O 2 - Current and Voltage O 3 - Resistance and Ohm’s Law.

Circuits & Electronics

Series, Parallel, and Series- Parallel Circuits

4.2.3A Ohm’s Law & Circuit Basics Why Make Electrons Flow Anyway?

Welcome to Physics Jeopardy Chapter 18 Final Jeopardy Question Equivalent Resistance 100 Complex circuits Misc Parallel.

CHAPTER Series, Parallel, and Series-Parallel Circuits 5 Copyright © 2016 by Pearson Education, Inc. All Rights Reserved Automotive Electrical and Engine.

=Ohms_Law Voltage (Volts) Current (Amps) Resistance (Ohms or Ω)

Register Digital Multimeter Usage Click Register to begin the course.

4.2.3B Electrical Power What About Watts?. Power Law Moving electrons (current) requires ENERGY How much energy gets used depends on: Strength of push.

1 HVACR - Refrigeration Series and Parallel Circuits.

1 2 Does the light bulb light? 3 Name the Symbol.

Physics 12 Circuits 4 – Parallel Mr. Jean. The plan: Video clip of the day Series Circuits –Mini-Lab - Series Parallel Circuits:

USING A DIGITAL VOLT- OHM - METER Automotive Technology Learning How Electricity Works.

1 HVACR216 - Hydronics Basic Circuits and Ohms Law.

4/17/10. Electric Circuits Circuit = Any path along which electrons can flow For a continuous flow of electrons, there must be a complete circuit with.

CHAPTER TWO CONTINUED. VOLTAGE Electrical pressure or potential The Electromotive force that causes the movement of electons Electrical pressure is measured.

Electrical Systems. VOCABULARYOBJECTIVES  Series circuit  Voltage drop  Kirchoff’s Voltage Law Describe a series circuit. Calculate the resistance.

Chapter 6 Series Circuits.

 Source of voltage difference ◦ Battery, outlet  At least one device that uses the electrical energy ◦ Radio, microwave, clock, etc  Conductor that.

Unfortunate book names:. A circuit must contain a source of potential difference, and a path for the flow of charge. It will probably also contain.

Circuits : Series vs Parallel

1 Chapter 20 Review activity! Fun in B208!.  A. Unit of energy  B. Unit of charge  C. Unit of current  D. Unit of voltage. 2 What is a coulomb?

Circuit Basics and Ohms Law. Types of Circuits There are two basic types of circuits SeriesParallel.

Concepts of Engineering and Technology Basic Electricity and Electronics: DC Circuits Copyright © Texas Education Agency, All rights reserved. 1.

a path along which electrons flow must have no breaks in the path to work 2 types: –closed (no breaks) –open (break, causes the device to shut off - switch)

Measuring Voltage and Current Aims Know the units of voltage and current Know how to measure voltage and current.

CELLS IN SERIES AND PARALLEL Lesson 9. Cells in Series  The electric potential given to a single electron by a dry cell has an average voltage of around.

Virtual Ground Introduction  A virtual ground is no more than a voltage divider where the divided network is the ground and the outer.

Ohms Law. EMF Ohm’s Law V = AxR V = IxR V = IxO All the same V A x R P 24.

Current and Power Calculations Practice Math once again!!!

Rank the substances in order of their index of refraction Substance A Substance B Substance C Substance A Substance D Substance E Substance B.

Check your Understanding

Electricity, Sound and Light

Ohm’s Law. Ohm’s Law Work, Energy, and Power Series Circuits.

Review Read the comments I have written in your book.

Ohm’s Law If the current I = 0.2A and the resistance R = 1000 ohms, solve for voltage. If V = 110V and R = ohms, how much current is flowing through.

Series and Parallel Circuits

FIGURE 6-1 The amount of current flowing into junction point A equals the total amount of current flowing out of the junction.

Science 9 Electricity Review.

Basic Electrical Calculations

FIGURE 6-1 The amount of current flowing into junction point A equals the total amount of current flowing out of the junction.

Electric Current.

Chapter Twenty: Electric Circuits

Series Circuit.

Modified by Mr. Wanninkhof

STATIC CHARGES I OR C? BATTERIES CURRENT CIRCUITS SCIENTISTS.

Science 9 Electricity Review.

Voltage Difference The difference in electrical potential between two places. Unit of measure = V (volts) Voltage causes current to flow through an electric.

Announcement Ohm’s law video is due at midnight Makeup lab today

Series and Parallel Circuits

Electric Circuits Chapter 35.

Parallel Circuits.

Current and Ohms law.

Presentation transcript:

STAiR Creation By Steven Adler NEXT

A voltage drop is the representation of energy used over a load device or resistance device in a circuit. If all loads are equal the amount of energy used over each load or resistance is equal. NEXT

Battery Ground Open switch Closed switch Resistance DVOM (Digital volt ohm meter) NEXT

Using your DVOM place you leads on either side of the load. Circuit with signal load on a open circuit. What is the power or voltage used over the light on the open circuit? NEXT

A volts12.00 volts B volts 6.00 volts C.0 volts0 volts D.8 volts8 volts

INCORRECT NEXT

12.00 volts would be incorrect. This circuit is open. No voltage is flowing through the circuit. So you would not use any voltage over the given load device. NEXT

INCORRECT NEXT

6.00 volts would be incorrect. This circuit is open. No voltage is flowing through the circuit. So you would not use any voltage over the given load device. NEXT

INCORRECT NEXT

6.00 volts would be incorrect. This circuit is open. No voltage is flowing through the circuit. So you would not use any voltage over the given load device. NEXT

CORRECT NEXT

The circuit is open, no power is flowing so the power or voltage used over the load is 0 volts. NEXT

Using your DVOM place you leads on either side of the load. Circuit with Signal load on a closed circuit. What is the power or voltage used over the light on the closed circuit? NEXT

A volts12.00 volts B volts 6.00 volts C. 0 volts 0 volts D.8 volts8 volts

INCORRECT NEXT

6.00 volts would be incorrect. This circuit is closed with only one load device. When only one load device is used all of the voltage or power is used. So all 12 volts would be used over the light. NEXT

INCORRECT NEXT

0 volts would be incorrect. This circuit is closed with only one load device. When only one load device is used all of the voltage or power is used. So all 12 volts would be used over the light. NEXT

INCORRECT NEXT

8 volts would be incorrect. This circuit is closed with only one load device. When only one load device is used all of the voltage or power is used. So all 12 volts would be used over the light. NEXT

CORRECT NEXT

The circuit is closed, power is flowing so all of the power or voltage is used over the load. So your DVOM reads volts. NEXT

A voltage drop is the representation of energy used over a load device or resistance device in a circuit. If all loads are equal the amount of energy used over each load or resistance is equal. NEXT

Battery Ground Open switch Closed switch Resistance DVOM (Digital volt ohm meter) NEXT

Using your DVOM place you leads on either side of the loads. Circuit with two equal loads on a open circuit. What is the power or voltage used over the light on the open circuit? NEXT

A.12.00v, 12.00v12.00v, 12.00v B.12.00v, 6.00v12.00v, 6.00v C.6.00v, 6.00v6.00v, 6.00v D.0.00v, 0.00v0.00v, 0.00v

INCORRECT NEXT

12.00v, 12.00v would be incorrect. This circuit is open with two load devices. No power or voltage is flowing through the circuit. So you would not use any voltage over the given load devices. NEXT

INCORRECT NEXT

12.00v, 6.00v would be incorrect. This circuit is open with two load devices. No power or voltage is flowing through the circuit. So you would not use any voltage over the given load devices. NEXT

INCORRECT NEXT

6.00v, 6.00v would be incorrect. This circuit is open with two load devices. No power or voltage is flowing through the circuit. So you would not use any voltage over the given load devices. NEXT

CORRECT NEXT

The circuit is open, no power is flowing so the power or voltage used over the loads is 0 volts and 0 volts.

A voltage drop is the representation of energy used over a load device or resistance device in a circuit. If all loads are equal the amount of energy used over each load or resistance is equal. NEXT

Battery Ground Open switch Closed switch Resistance DVOM (Digital volt ohm meter) NEXT

Using your DVOM place you leads on either side of the loads. Circuit with two loads on a closed circuit. What is the power or voltage used over each of the lights on the closed circuits? NEXT

A.12.00v, 12.00v12.00v, 12.00v B.12.00v, 6.00v12.00v, 6.00v C.6.00v, 6.00v6.00v, 6.00v D.0.00v, 0.00v0.00v, 0.00v

INCORRECT NEXT

12.00 volts, volts would be incorrect. This circuit is closed with two load devices. When two equal load devices are used, half of the voltage or power is used over each load. So 12 volts would be split over the two lights. Or six volts used over each light. NEXT

INCORRECT NEXT

12.00v, 6.00v would be incorrect.. This circuit is closed with two load devices. When two equal load devices are used, half of the voltage or power is used over each load. So 12 volts would be split over the two lights. Or six volts used over each light. NEXT

INCORRECT NEXT

0.00v, 0.00v would be incorrect.This circuit is closed with two load devices. When two equal load devices are used, half of the voltage or power is used over each load. So 12 volts would be split over the two lights. Or six volts used over each light. NEXT

CORRECT NEXT

This circuit is closed with two load devices. When two equal load devices are used, half of the voltage or power is used over each load. So 12 volts would be split over the two lights. Or six volts used over each light volts, 6.00 volts.

A voltage drop is the representation of energy used over a load device or resistance device in a circuit. If all loads are equal the amount of energy used over each load or resistance is equal. NEXT

Battery Ground Open switch Closed switch Resistance DVOM (Digital volt ohm meter) NEXT

CONGRATULATIONS!!! You have completed the voltage drop STAiR lesson. GOOD JOB