Heat Recovery Methods (Heat Exchangers)

Slides:



Advertisements
Similar presentations
ENERGY CONVERSION MME 9617A Eric Savory
Advertisements

Analysis of heat exchangers: Use of the log mean temperature Difference LMTD Method: Q= (m cp ∆T) h = (m cp ∆T) c Q= U A F∆T lm A=N װ DL ∆ T lm = ∆T l.
Heat Exchangers: Design Considerations
MER Design of Thermal Fluid Systems
Closure of Kern’s Method
CONTROL FOR HEAT EXCHANGE M. B. JENNINGS CHE 185 FEB 2006.
Figure 1.1 The observer in the truck sees the ball move in a vertical path when thrown upward. (b) The Earth observer views the path of the ball as a parabola.
Cost Estimation Of A Heat Exchanger Group Members Chinthaka Perera Chris Peng Sandy Lee Terry Peters 540:343 Engineering Economics Spring 1998.
Chapter 3.1: Heat Exchanger Analysis Using LMTD method
Done By Moh’d Saad Jalmood To Dr. Malek Al Ahmed.
Heat Exchanger Chapter 7 Part 1. Categories Regenerators Open-type Closed type also called recuperator.
Heat Exchanger Effectiveness Maximum and Minimum Heat Capacity Rates Number of Transfer Units Maximum Temperature Difference.
Heat Exchanger & Classification Prepared by: Nimesh Gajjar
HEAT EXCHANGER.
HEAT EXCHANGERS.
1 MER Design of Thermal Fluid Systems Project 3 Heat Exchanger Optimization Professor Anderson Spring 2012.
Heat Exchangers This is session 19 in curriculum manual.
$100 $200 $300 $400 $500 $100 $200 $300 $400 $500 $100 $200 $300 $400 $500 $100 $200 $300 $400 $500 $100 $200 $300 $400 $500 $100 $200 $300.
$100 $200 $300 $400 $500 $100 $200 $300 $400 $500 $100 $200 $300 $400 $500 $100 $200 $300 $400 $500 $100 $200 $300 $400 $500 $100 $200 $300.
Cooling System. 1. List the basic parts of a cooling system: -Thermostat -Fan -Water pump -Radiator -Ethelyne glycole -Shroud.
ME T HERMAL F LUID S YSTEM D ESIGNS Heat Exchanger Final Project.
ME 414 Project 2 Heat Exchanger Design Date: - May 6, 2009 Instructor: - John Toksoy Member: - Rahul Patel Hesam Nouri Atoosa Solhkonan Juan Tapia.
Chapter 11 Heat Exchangers ( ) Heat Exchangers.
Heat Exchanger Design Cooler E-100 Heater E-108.
CLASSIFICATION OF HEAT EXCHANGERS
Concentric Tube (double-pipe) Heat Exchangers
Heat Exchangers Jorge Seda #84012 José Luis García #69260 Billy Gerena #73656 Robert De Aza #66880 Prof. Eduardo Cabrera ME
The 3 Types of Heat Transfer
Government Engineering College
Chapter 11: Heat Exchangers
HEAT EXCHANGERS Red Sea University Faculty of Engineering
Unit 42: Heat Transfer and Combustion
ERT 216 HEAT AND MASS TRANSFER
Energy balance for the compressor in this figure:
CONTENTS DESIGN PROBLEM INTRODUCTION FLOW CHART OF DESIGN
HEAT EXCHANGER DESIGNPROJECT ME 414 Thermal Fluid System Design
Date of download: 11/12/2017 Copyright © ASME. All rights reserved.
ECE Engineering Design Thermal Considerations
HEAT EXCHANGER.
The Basic Direct Expansion Refrigeration Cycle
WHAT IS HX……??? Heat exchangers are equipment that transfer
Heat Exchanger Analysis
Perpindahan Panas Heat Exchanger.
Shell and tube heat exchanger
2.1 Space and Time 1.
Chapter 11: Heat Exchangers
Concentric Tube (double-pipe) Heat Exchangers
انواع المخاليط (التدريس الابداعي )
P M V Subbarao Professor Mechanical Engineering Department I I T Delhi
Steam / condensate system Heat recovery – cleaning circuit
Matter and Measurement Vocabulary
Shell and tube heat exchanger
Image Bank Chapter 10 Preview Diffusion Unit Cells Crystalline Solids
Heat Exchangers Heat Exchangers.
Changes of state, the cooling curve and latent heat
Changes of State units: J/g Heat of Vaporization
Copy Questions or write answer in a complete sentence!
Conduction Investigation 4 Part 2.
Chapter 11 HEAT EXCHANGERS Mehmet Kanoglu University of Gaziantep Copyright © 2011 The McGraw-Hill Companies, Inc. Permission required for reproduction.
States of Matter.
Modified Definitions for Library of Ideas TEMA : An authorized body for innovation & Standardization. Shell side fluid : 1 Tube side fluid.
Heating and Cooling Curves
What is the matter?.
The Particle Model of Matter
What is the matter?.
Phase Changes Notes.
Dose in l/h clean liquid
Thermal Energy.
Volume Notes 8/27/19.
S1 Chemistry Introduction to Chemistry
Presentation transcript:

Heat Recovery Methods (Heat Exchangers)

Recuperator (Gas to Gas)

Recuperator (Gas to Gas)

Economizer (Gas to Liquid)

Economizer (Gas to Liquid)

Shell and Tube Heat Exchanger (counter-flow, single pass)

Shell and Tube Heat Exchanger (counter-flow)

Finned Heat Exchanger

Conventional Finned Thermoelectric heat exchanger design Note: All dimensions are in meters. Heat exchanger length is 0.508 m.

Conventional TE heat exchanger design Direct Contact TE heat exchanger design

Darcy Friction Factor fD

Fanning Friction Factor f

Fig. 11.19, Solid curves for Cmin mixed and Cmax unmixed, Dashed curves for Cmin unmixed and Cmax mixed

Feedback: Privacy Policy Feedback
Do Not Sell My Personal Information
About project: SlidePlayer Terms of Service

© 2025 SlidePlayer.com. Inc. All rights reserved.