Voltages Sources and Current Sources

Slides:

Advertisements

Similar presentations

CE ELECTRICAL PRINCIPLES STEADY STATE ANALYSIS OF SINGLE PHASE CIRCUITS UNDER SINUSOIDAL EXCITATION 1 Steady State response of Pure R,L and C &

Advertisements

Kirchhoff’s Laws.

Voltage and Current Division

Unit 8 Combination Circuits

Unit 8 Combination Circuits

Impedance and Admittance. Objective of Lecture Demonstrate how to apply Thévenin and Norton transformations to simplify circuits that contain one or more.

Kirchhoff’s Laws Three Examples

Objective of Lecture Provide step-by-step instructions for nodal analysis, which is a method to calculate node voltages and currents that flow through.

1 AC Source Exchange Discussion D16.3 Chapter 4 Section 4-11.

Lesson 24 AC Power and Power Triangle

Storey: Electrical & Electronic Systems © Pearson Education Limited 2004 OHT 13.1 Capacitance and Electric Fields  Introduction  Capacitors and Capacitance.

Series RLC Network. Objective of Lecture Derive the equations that relate the voltages across a resistor, an inductor, and a capacitor in series as: the.

If current is disrupted through one element (e.g. the light goes out) If current is disrupted through one element (e.g. the light goes out) then they.

Objective of Lecture Provide step-by-step instructions for mesh analysis, which is a method to calculate voltage drops and mesh currents that flow around.

Objective of Lecture Describe what a single node, a distributed node, branch, and loop are. Chapter 2.3 Explain the differences between a series and parallel.

Source-Free RLC Circuit

Resistors in Series and Parallel Circuits. Resistors in circuits To determine the current or voltage in a circuit that contains multiple resistors, the.

Lecture - 7 Circuit Theorems

Objective of Lecture Explain mathematically how resistors in series are combined and their equivalent resistance. Chapter 2.5 Explain mathematically how.

Parallel RLC Network. Objective of Lecture Derive the equations that relate the voltages across a resistor, an inductor, and a capacitor in parallel as:

Series and Parallel AC Circuits

A Differentiator Circuit.  All of the diagrams use a uA741 op amp. ◦ You are to construct your circuits using an LM 356 op amp.  There is a statement.

Series and Parallel Circuits

Series Circuits Circuits in which there is only one path for current to flow through All elements of the circuit (resistors, switches etc…) are in the.

Series RLC Network. Objective of Lecture Derive the equations that relate the voltages across a resistor, an inductor, and a capacitor in series as: the.

Basic Electrical Engineering Lecture # 04 Simple Resistive Circuits Course Instructor: Engr. Sana Ziafat.

Objective of Lecture Provide step-by-step instructions for mesh analysis, which is a method to calculate voltage drops and mesh currents that flow around.

Chapter 9 Network Theorems.

Chapter 19 DC Circuits. Objective of the Lecture Explain Kirchhoff’s Current and Voltage Laws. Demonstrate how these laws can be used to find currents.

Storey: Electrical & Electronic Systems © Pearson Education Limited 2004 OHT 15.1 Alternating Voltages and Currents  Introduction  Voltage and Current.

Series wiring means that the devices are connected in such a way that there is the same electric current through each device. One loop only for the flow.

SERIES RESISTORS AND VOLTAGE DIVISION In Fig the two resistors are in series, since the same current i flows in both of them. Applying Ohm’s law.

Step Response Series RLC Network.

Fundamentals of Electric Circuits

Unit 8 Phasors.

Series and Parallel Wiring GET A CALCULATOR!!!!!.

Today’s agenda: Capacitance. You must be able to apply the equation C=Q/V. Capacitors: parallel plate, cylindrical, spherical. You must be able to calculate.

Objective of Lecture Introduce the superposition principle. Chapter 4.3 Fundamentals of Electric Circuits Provide step-by-step instructions to apply superposition.

Lecture 03: AC RESPONSE ( REACTANCE N IMPEDANCE ).

Kirchhoff’s Laws Kirchhoff’s Current Law Kirchhoff’s Voltage Law Series Circuits Parallel Circuits Polarity.

Lesson 6: Current Sources Source Conversion

Objective of Lecture Introduce the superposition principle Provide step-by-step instructions to apply superposition when calculating voltages and currents.

When current is flowing in an ordinary metal wire, the magnitude of the average velocity of the electrons is closest to A) 1 m/s. B) 1 km/s. C) 10 m/s.

DC Circuits AP Physics Chapter 18. DC Circuits 19.1 EMF and Terminal Voltage.

1 Lecture #6 EGR 272 – Circuit Theory II Read: Chapter 9 and Appendix B in Electric Circuits, 6 th Edition by Nilsson Using Phasors to Add Sinusoids Sinusoidal.

Section Objectives  Describe how current divides in a parallel circuit.  Determine the voltage across and current through each branch of a parallel.

Chapter 10 RC Circuits.

1© Manhattan Press (H.K.) Ltd Series combination of resistors, capacitors and inductors Resistor and capacitor in series (RC circuit) Resistor and.

RC Circuits (sine wave)

Lesson 7: Current Sources / Source Conversion

Lesson 9 Parallel Circuits.

Lesson 2-1 Properties of Numbers.

Thévenin and Norton Transformation

Nodes, Branches, and Loops

Voltage and Current Division

Nodes, Branches, and Loops

Step Response Parallel RLC Network.

Electrical energy By; Kemi and Kim.

Voltage and Current Division

Kirchoff’s Laws.

Superposition Theorem.

Kirchoff’s Laws.

Series and Parallel Resistors

Voltage and Current Division

Kirchhoff’s Laws.

Superposition Theorem

Kirchhoff’s Laws.

Presentation transcript:

Voltages Sources and Current Sources Series and Parallel Combinations

Objective of Lecture Explain how voltage sources in series may be combined. Explain how current sources in parallel may be combined. Explain under what conditions voltage sources in parallel and current sources in parallel are allowed.

Voltage Sources in Series DC voltage sources in series can be combined and replaced with a single source. AC voltage sources in series can be combined and replaced with a single source only if the angular frequency of operation w are identical. DC and AC voltage sources can be added together when calculating a total voltage. AC voltage sources operating at different frequencies can be added together. The current flowing through one voltage source must be equal to the current flowing through the other voltage source.

Example 1

Example 2 Or

Example 3 Or Or

Example 4 Or Or

DC and AC sources A 5V dc voltage source in series a 2V sin(10t) ac voltage source has a total combined voltage of 5V+2Vsin(10t). However, we do not have a symbol for a single voltage source that can replace the symbols for the dc and ac sources.

AC sources with Different w A 2V ac voltage source operating at 10 rad/s in series with a 2V ac voltage source operating at 10.5 rad/s has a total voltage of 2Vsin(10t)+2Vsin(10t). Again, there is not a symbol for a single ac voltage source that can replace the symbols for the two ac sources operating at different frequencies.

Voltage Sources in Parallel Since the voltage sources share common nodes, the only time two or more voltage sources are allowed in parallel is when they have exactly the same voltage, polarity, and frequency of operation (if ac sources). The multiple voltage sources can be replaced by a single source with the same voltage, polarity, and frequency of operation (if ac sources).

Example 5 Allowed Not Allowed

Example 6 Allowed Not Allowed

Current Sources in Parallel DC current sources in parallel can be combined and replaced with a single source. AC current sources in parallel can be combined and replaced with a single source only if the angular frequency of operation w are identical. DC and AC current sources in parallel can be added together when calculating a total current. AC current sources operating at different frequencies can be added together. The voltage drop across one current source must be equal to the voltage dropped across the other current sources in parallel.

Example 7

Example 8

Example 9 Or

DC and AC Current Sources A 5A dc current source in parallel a 2A sin(10t) ac current source means that they are contributing a total current of 5A+2Asin(10t) at that node. However, we do not have a symbol for a single current source that can replace the symbols for the dc and ac sources.

AC Sources with Different w A 2A ac current source operating at 10 rad/s in parallel with a 2V ac current operating at 10.5 rad/s means that they are contributing a total current of 2Asin(10t)+2Asin(10t) at that node. Again, there is not a symbol for a single ac current source that can replace the symbols for the two ac sources operating at different frequencies.

Current Sources in Series Since components in series must have the same current flowing through each source, the only time two or more currents sources are allowed in series is when they have exactly the same magnitude current, the current is flowing in the same direction, and frequency of operation (if ac sources). The multiple current sources in series can be replaced by a single source with the same magnitude, direction of current flow, and frequency of operation (if ac sources).

Example 10 Allowed Not Allowed

Summary Voltage sources in series can be added. Current sources in parallel can be added. Only in the case where the magnitude, polarity, and frequency of operation are identical can multiple voltage sources be in parallel. They can be replaced with a single voltage source of the same magnitude, polarity, and frequency of operation. Only in the case where the magnitude, direction of current flow, and frequency of operation are identical can multiple currents sources be in series. They can be replaced with a single current source of the same magnitude, direction of current flow, and frequency of operation.