Bending Test Conduct Bending Test

Slides:



Advertisements
Similar presentations
Lab #6 Report due TODAY Individual Data Processing and Individual Write Up Lab #6 Report is due TODAY by midnight Answer Multiple Choice Questions ONLINE.
Advertisements

Lab #3 Report due TODAY Individual Data Processing and Individual Write Up Lab #3 Report is due TODAY by midnight Answer Multiple Choice Questions ONLINE.
GTA : Office: room, hours UTA : USE ITAP ACCOUNTS TO LOG ON Welcome to L0*-0* Record Info on last page of manual.
Tensile Testing – Data Sheet Please fill in your name, group members, data and instructor’s name Mark gage length indents using the hammer Measure the.
PLEASE PASS YOUR HOMEWORK TO THE CENTER ISLE TAKE EVERYTHING OFF YOUR DESKS EXCEPT A PENCIL OR PEN AND CALCULATOR: QUIZ TIME 1.
1 times table 2 times table 3 times table 4 times table 5 times table
Writing and Solving Proportions. Proportions Proportion is an equation stating that two ratios are equivalent. Proportional are two quantities that form.
Lab #5 Due Today Individual Data Processing and Individual Write Up
Combined Loading Test Perform Bending Only Test to obtain Elastic Modulus and Poisson’s Ratio Compare the materials properties Perform Combined Loading.
Lab #1: Poisson’s Ratio Determine Poisson’s Ratio Determine Elastic Modulus ASTM Standard E132.
EWEC 2007 Centre for Renewable Energy Sources Wind Turbine Testing Laboratory WT Load Measurements: A Comparison between Load- Based and Analytical Calibration.
University of Chemical Technology and Metallurgy Department of Material Science and Engineering FINITEELEMENT METHOD By eng. Veselin Paunov Prof. Veselin.
$100 $200 $300 $400 $500 $100 $200 $300 $400 $500 $100 $200 $300 $400 $500 $100 $200 $300 $400 $500 $100 $200 $300 $400 $500 $100 $200 $300.
$100 $200 $300 $400 $500 $100 $200 $300 $400 $500 $100 $200 $300 $400 $500 $100 $200 $300 $400 $500 $100 $200 $300 $400 $500 $100 $200 $300.
Chapter 9-Statics, Dynamics and Mechanical Engineering Objectives and what should you Know: What are statics and Dynamics? What are the Newtons’s three.
Q: How do I view and upload a document? First, Login to NTREIS Transactions First, Login to NTREIS Transactions.
Lab #4 Report due TODAY Individual Data Processing and Individual Write Up Lab #4 Report is due TODAY by midnight Answer Multiple Choice Questions ONLINE.
MECH 322 Instrumentation Lab 5 Elastic Modulus of an Aluminum Beam Performed: February 13, 2007 Group 0 Miles Greiner Lab Instructors: Mithun Gudipati,
Solve by Factoring Zero Product Property.
$100 $200 $300 $400 $500 $100 $200 $300 $400 $500 $100 $200 $300 $400 $500 $100 $200 $300 $400 $500 $100 $200 $300 $400 $500 $100 $200 $300.
Tables Learning Support
Thursday, August 14, 2014 Day 2 Science Starters Sheet 1. Please have these Items on your desk. I.A Notebook 2- Science Starter: Two vocabulary words:
Activity 3.10 The Elastic Ball. Read page 370 and use your graphing calculator to make a scatter plot –Use the function they give you in 4 to answer question.
Torsion Testing Become familiar with Tinius Olsen Torsion Tester (10,000 in-lb capacity) ASTM E-143 Test Method Draw Shear Stress-Strain Curve Determine.
Atomic Simulation Term Report Thur. POSTECH M.S.E Kim Kyeong-Min.
ISE 311 Tensile Testing Lab in conjunction with Section 3.1 in the text book “Fundamentals of Modern Manufacturing” Third Edition Mikell P. Groover 4/25/2008.
PROPERTIES OF MATERIALS ENF 150 Chapter 10: Properties of Materials.
Presentation Overview
Pendahuluan Material Komposit
The various engineering and true stress-strain properties obtainable from a tension test are summarized by the categorized listing of Table 1.1. Note that.
An –Najah National University
Materials Engineering
Mechanics of Materials
selection of materials, stresses
Modulus of elasticity (GPa) Shear modulus elasticity (GPa)
MSE 527 Lab Mechanical Behavior of Materials
CHAPTER 6: MECHANICAL PROPERTIES
Stress and Strain – Axial Loading
Stress and Strain – Axial Loading
Tensile strength (MPa) Length (m) of fibers/kg
Lab #1: Poisson’s Ratio Determine Poisson’s Ratio
M. M. Shokrieh*, M. Salamat-talab
Rigidity Modulus (Gpa)
Thermal Properties of Materials
Tensile Testing of Aluminum Alloy
Times Tables.
M. M. Shokrieh*, M. Salamat-talab
مراجعة عامة.
Material Joining and Beam Bending
Population Dispersion of Spider Webs
CTC / MTC 222 Strength of Materials
Experiment # 2 Torsion Test
Implementation of 2D stress-strain Finite Element Modeling on MATLAB
Lecture 9 – Deformation and Damage
Tutorial in Mechanical Properties
Lecture 9 – Deformation and Damage
Lab Notebook Name, Period, Class should be on outside front cover in pen Name Period Class.
Graphical design for specified laminate strain limits
Mechanical Properties: 1
Shear in Rubber Apparatus
Mechanical properties of metals Stress and Strain in metals
Lab Report Guidelines.
3 times tables.
6 times tables.
Dr. Mohammed Abdulrazzaq
M. M. Shokrieh*, M. Salamat-talab
Mechanical Properties Of Metals - I
Tutorial.
Experimental Mechanics - assignment
Experiment for Week 4 Determining the Identity of Several Unknown Substances using Physical Properties CHE116.
Presentation transcript:

Bending Test Conduct Bending Test Determine Elastic Modulus & Poisson’s Ratio of material Comparison to handbook value and previous Lab #1 results Submit Lab Report

Bending Test Data Sheet 2024-T351 Al-Cu Alloy

Conduct the Bending Test Please initialize the Strain Meter a couple of times to ensure that it indicates zero strains at zero load, and that there is NO DRIFT with time

Processing Data

Elastic Modulus Plot

Poisson’s Ratio Plot

Material Properties

Lab #4 Report due next week Cover Page + Abstract Data Sheet Spreadsheet Plot #1: Elastic Modulus Plot #2: Poisson’s Ratio Material Property Tables (two tables) Comments and Conclusions

Feedback: Privacy Policy Feedback
Do Not Sell My Personal Information
About project: SlidePlayer Terms of Service

© 2025 SlidePlayer.com. Inc. All rights reserved.