Say "Goodbye" to nuts, clamps, crimping, welding, or soldering and say "Hello" to the Quick Fitting, Inc. COPRO quick connection fitting technology. The.

Slides:

Advertisements

Similar presentations

UNIVERSITY of NORTHERN COLORADO HOT WORK PROGRAM.

Advertisements

Using Gas Welding Equipment

Ag Metals I Using Gas Welding Equipment. Objectives Identify major part of oxyacteylene welding equipment Change oxygen and acetylene cylinders Turn on.

英語歌曲教唱 Sing in English! 最終回 – Hello, Goodbye.

Multi-Sync Repair Training DPM Diversified Products Mfg Inc. Click the Mouse or use the Down Arrow to advance to the next point.

Multi-Sync Repair Training

Student Book © 2004 Propane Education & Research CouncilPage Installing Copper Tubing in Distribution Systems Personnel who install copper.

1 HVACR316 – Piping Torches, Tanks, and Tips. 2 Soldering Basics Soldering is a process used to join piping and tubing to fittings. It is used primarily.

Multi-Sync Repair Training DPM Diversified Products Mfg Inc. Click the Mouse or use the Down Arrow to advance to the next point.

Electrical Repair Soldering and Crimping By Fernando Martinez And Rudy.

Welding Safety in Agriculture OSHA Standard Produced by Idaho State University Office of Workforce Training.

OXYFUEL WELDING. INTRODUCTION Oxyfuel welding is a welding process where the heat for fusion is supplied by a torch using oxygen and a fuel gas. Several.

Environmental Health and Safety 6 Eisenhower Parking Deck University Park, PA Penn State University Hot Work Permits.

SAFETY TALK - SLIDE 1 OF 14 Elkhart Products Corporation 08/00 WELCOME ELKHART PRODUCTS CORPORATION “TOOLBOX SAFETY TALK” Welding, Cutting, & Burning.

Transportation Tuesday TRANSPORTATION TUESDAY A quick quiz! Find out how much you really know Learning the techniques and finding different ways to deal.

Welding, Cutting, & Burning. GENERAL HAZARDS General hazards of welding include: –Impact –Penetration –Harmful dust –Smoke –Fumes –Heat –Light radiation.

1 Copyright  2004 Lincoln Global Inc. Oxy Fuel Welding Troubleshooting.

Standard 29 CFR Part Welding, Cutting and Brazing Training.

1 Welding Module 10. 2Objectives After this module you should be able to – identify the most common welding hazards – take the necessary steps to avoid.

Welding, Cutting and Brazing 29 CFR 1910, Subpart Q

HOT WORK PROCEDURES Welding and Hot Work, such as brazing or grinding present a significant opportunity for fire and injury. CCR Title 8 Sub Chapter 7,

Welding, Subpart J OSHA 500 Course. Critical Hazards n Heat is a source of ignition in the various welding processes n Welding fumes can become a health.

Copyright  Business & Legal Reports, Inc. BLR’s Safety Training Presentations Welding, Cutting and Brazing 29 CFR 1910, Subpart Q.

It is amazing to be able to join metal using heat. The process we use in making jewelry is called soldering… it is closest to brazing in the world of.

Lumbermen’s Underwriting Alliance

Hello, Good-bye by John Lennon and Paul McCartney Hello-Goodbye-klibi/540730/

Unit 7: Tubing And Piping

Residential Plumbing Where does the water in your home come from and where does it go?

FHM TRAINING TOOLS This training presentation is part of FHM’s commitment to creating and keeping safe workplaces. Be sure to check out all the training.

Multi-Sync Repair Training DPM Diversified Products Mfg Inc. Click the Mouse or use the Down Arrow to advance to the next point.

FFA CAREER DEVELOPMENT EVENT Part 4

SHOP SPEED DATE Get to know your work place. #1: MSDS A Material Safety Data Sheet (MSDS) is a document that contains information on the potential hazards.

SMAW (Stick Welding). 2 SMAW Unit Topics During this overview, we will discuss the following topics: Safety SMAW Basics Equipment Set-Up Welding Variables.

Hot Work Procedure Training

Hot work permit.

100 Addition Facts DIRECTIONS:  Watch the screen.  Say the answer to each addition fact when it appears.  You have 3 seconds to say each answer.

Basic Home Plumbing.

Soldering & Brazing ALWAYS USE LEAD FREE SOLDER!!!!

1 HVACR316 - Piping Torches, Tips, Tanks Torches, Tips, Tanks.

ID 1.75 Material list: aluminum ¼ X ¾ X 6 in flat bar ¾ X 6 in round stock 1 X 6 in round stock 2 ea 5/16 heli-coil Weld 1” joints.

Copyright © 2010 Delmar, Cengage Learning. ALL RIGHTS RESERVED. Unit 13 Fastening Metal.

Attention Small Businesses Do you want to become the success you so deserve to be? And lack of capital keeping you from reaching that goal? There is an.

 Brazing may be define as a techniques of joining two similar or dissimilar materials by additional of special filler metal.

Welding Safety What’s Wrong In this Picture?. © Business & Legal Reports, Inc. Session Objectives You will refresh your knowledge on how to: Protect yourself.

©2007 John Wiley & Sons, Inc. M P Groover, Fundamentals of Modern Manufacturing 3/e BRAZING 1.Brazing.

Just Call on our Kindle Fire Phone number Toll Free for any type of eBook related issues, we are here 24*7 to give you best Service for.

Hot Work Permit Osan AB Fire Emergency Services.

Flow and Control Engineering Supplying Control Valves & Instrumentation to Heavy Industry and Chemical Manufacturing. Multi-Stage Steam & Condensate Control.

Images were sourced from the following web sites: Slide 2:commons.wikimedia.org/wiki/File:BorromeanRing...commons.wikimedia.org/wiki/File:BorromeanRing...

Chapter 31 Plumbing Systems Copyright Goodheart-Willcox Co., Inc. May not be posted to a publicly accessible website. Cite codes that govern the installation.

Hello Educational presentation.

Line Blinding/Blanking Options

Teknologi Dan Rekayasa

Using Gas Welding Equipment

Now What? Forgot to Pull a Permit?

HOT WORK PROCEDURES & PERMIT Intrepid Policy

Penn State University Hot Work Permits

Phone: + 40 (728) | +40 (733)

Enter your , phone, etc Enter your , phone, etc

HELLO THERE. THIS IS A TEST SLIDE SLIDE NUMBER 1.

Enter your name, , phone number etc.

Place all the time and date information for all your events

PRESSURE EQUIPMENT REPAIRS API 510/570 and ASME PCC-2 are both PCCs

Oil Field Contractor Fatality Case Study

Industrial Pipe Insulation

Hello Hi Hello Hi Hello Hi Hello Hi Hello Hi Hello Hi.

Presentation transcript:

Say "Goodbye" to nuts, clamps, crimping, welding, or soldering and say "Hello" to the Quick Fitting, Inc. COPRO quick connection fitting technology. The simple high quality, permanent, reusable fitting.

No flame, no fire watch, easy and safe access to tight spaces, no torch, no propane tanks, no flux, no solder, no fire extinguishers, no fire permits, no fire insurance claims, no noxious fumes, reduced flushing time

Quick FittingCompressionCrimpingGluedSolderedThreaded Reusable YesNR---Yes Slide to Connect Yes-- -- Reposition able Yes --- Repairable Yes Second Connect Yes----- Repair Pipe Wet Yes ---- Simple to Use Yes-----

PHONE: WEB: