LAN switching and Bridges

Slides:



Advertisements
Similar presentations
Interconnection: Switching and Bridging
Advertisements

Interconnection: Switching and Bridging CS 4251: Computer Networking II Nick Feamster Fall 2008.
Communication Networks Recitation 3 Bridges & Spanning trees.
University of Calgary – CPSC 441.  We need to break down big networks to sub-LANs  Limited amount of supportable traffic: on single LAN, all stations.
CS 356: Computer Network Architectures Lecture 8: Learning Bridges and ATM Ch 3.1 Xiaowei Yang
CMPE 150- Introduction to Computer Networks 1 CMPE 150 Fall 2005 Lecture 19 Introduction to Computer Networks.
Connecting LANs: Section Figure 15.1 Five categories of connecting devices.
CSE 534 Fundamentals of Computer Networks Lecture 4: Bridging (From Hub to Switch by Way of Tree) Based on slides from D. Choffnes Northeastern U. Revised.
CS 4700 / CS 5700 Network Fundamentals Lecture 7: Bridging (From Hub to Switch by Way of Tree) Revised 1/14/13.
CPSC 441 TUTORIAL TA: FANG WANG HUBS, SWITCHES AND BRIDGES Parts of the slides contents are courtesy of the following people: Jim Kurose, Keith Ross:
1 Computer Networks Internetworking Devices. 2 Repeaters Hubs Bridges –Learning algorithms –Problem of closed loops Switches Routers.
COMS/CSEE 4140 Networking Laboratory Lecture 07 Salman Abdul Baset Spring 2008.
CSEE W4140 Networking Laboratory Lecture 8: LAN Switching Jong Yul Kim
W4140 Network Laboratory Lecture 7 Oct 23 - Fall 2006 Shlomo Hershkop Columbia University.
1 LAN switching and Bridges Relates to Lab 6. Covers interconnection devices (at different layers) and the difference between LAN switching (bridging)
CSE390 Advanced Computer Networks Lecture 7: Bridging (From Hub to Switch by Way of Tree) Based on slides from D. Choffnes Northeastern U. Revised Fall.
Introduction to Computer Networks 09/23 Presenter: Fatemah Panahi.
COMS W COMS W Lecture 7. LAN Switching: Bridges & Spanning Tree Protocol.
LAN switching and Bridges
1 LAN switching and Bridges Relates to Lab 6. Covers interconnection devices (at different layers) and the difference between LAN switching (bridging)
1 Computer Networks LAN Bridges and Switches. 2 Where are we?
Layer 2 Switch  Layer 2 Switching is hardware based.  Uses the host's Media Access Control (MAC) address.  Uses Application Specific Integrated Circuits.
Connecting LANs, Backbone Networks, and Virtual LANs
T. S. Eugene Ngeugeneng at cs.rice.edu Rice University1 COMP/ELEC 429 Introduction to Computer Networks Lecture 8: Bridging Slides used with permissions.
1 LAN switching and Bridges. 2 Outline Interconnection devices Bridges/LAN switches vs. Routers Bridges Learning Bridges Transparent bridges.
1 CS 4396 Computer Networks Lab LAN Switching and Bridges.
1 LAN switching and Bridges CS491G: Computer Networking Lab V. Arun Slides adapted from Liebeherr and El Zarki, and Kurose and Ross.
CSC 336 Data Communications and Networking Lecture 7d: Interconnecting LAN Dr. Cheer-Sun Yang Spring 2001.
Review: –Ethernet What is the MAC protocol in Ethernet? –CSMA/CD –Binary exponential backoff Is there any relationship between the minimum frame size and.
Ethernet (LAN switching)
OSI Model. Switches point to point bridges two types store & forward = entire frame received the decision made, and can handle frames with errors cut-through.
T. S. Eugene Ngeugeneng at cs.rice.edu Rice University1 COMP/ELEC 429 Introduction to Computer Networks Scaling Broadcast Ethernet Some slides used with.
Configuring Cisco Switches Chapter 13 powered by DJ 1.
1 Data Link Layer Lecture 23 Imran Ahmed University of Management & Technology.
McGraw-Hill©The McGraw-Hill Companies, Inc., 2004 Connecting Devices CORPORATE INSTITUTE OF SCIENCE & TECHNOLOGY, BHOPAL Department of Electronics and.
1 © 2003, Cisco Systems, Inc. All rights reserved. CCNA 3 v3.0 Module 7 Spanning Tree Protocol.
M. Veeraraghavan (originals by J. Liebeherr) 1 Need for Routing in Ethernet switched networks What do bridges do if some LANs are reachable only in multiple.
ICS 156: Networking Lab Magda El Zarki Professor, ICS UC, Irvine.
M. Veeraraghavan (originals by J. Liebeherr) 1 Internetworking Bridges Routing with Bridges * * Reading material is EL 536 textbook (sections 14.1 and.
5: DataLink Layer 5a-1 Bridges and spanning tree protocol Reference: Mainly Peterson-Davie.
1 Chapter 3: Packet Switching (Switched LANs) Dr. Rocky K. C. Chang 23 February 2004.
1 LAN switching and Bridges Relates to Lab Outline Interconnection devices Bridges/LAN switches vs. Routers Bridges Learning Bridges Transparent.
1 LAN switching and Bridges Relates to Lab 6. Covers interconnection devices (at different layers) and the difference between LAN switching (bridging)
Chapter 3 Part 1 Switching and Bridging
Ethernet switches and IP routers
Chapter 16– Connecting LANs
CS 3700 Networks and Distributed Systems
Advanced Computer Networks
MAC Addresses and ARP 32-bit IP address:
Bridging.
3. Internetworking (part 2: switched LANs)
Chapter 4 Data Link Layer Switching
Spanning Tree Algorithm
: An Introduction to Computer Networks
ARP: Address Resolution Protocol
Chapter 3 Part 1 Switching and Bridging
CS 3700 Networks and Distributed Systems
CS 457 – Lecture 8 Switching and Forwarding
Intra-Domain Routing Jacob Strauss September 14, 2006.
LAN switching and Bridges
CS 4700 / CS 5700 Network Fundamentals
NT2640 Unit 9 Activity 1 Handout
Chapter 6 The Link Layer and LANs
LAN switching and Bridges
CS 4700 / CS 5700 Network Fundamentals
Dr. Rocky K. C. Chang 23 February 2004
Connections Johan Lukkien
Chapter 15. Connecting Devices
LAN switching and Bridges
Presentation transcript:

LAN switching and Bridges Relates to Lab 6. Covers interconnection devices (at different layers) and the difference between LAN switching (bridging) and routing. Then discusses LAN switching, including learning bridge algorithm, transparent bridging, and the spanning tree protocol.

Outline Interconnection Devices Bridges/LAN Switches vs. Routers Learning Bridges Transparent bridges

Introduction There are many different devices for interconnecting networks

Ethernet Hub Used to connect hosts to Ethernet LAN and to connect multiple Ethernet LANs Collisions are propagated

Bridges/LAN Switches A bridge or LAN switch is a device that interconnects two or more Local Area Networks (LANs) and forwards packets between these networks. Bridges/LAN switches operate at the Data Link Layer (Layer 2)

Terminology: Bridge, LAN Switch, Ethernet Switch There are different terms to refer to a data-link layer interconnection device: The term bridge was coined in the early 1980s. Today, the terms LAN switch or (in the context of Ethernet) Ethernet switch are used. Convention: Since many of the concepts, configuration commands, and protocols for LAN switches were developed in the 1980s, and commonly use the old term `bridge’, we will, with few exceptions, refer to LAN switches as bridges.

Ethernet Hubs vs. Ethernet Switches An Ethernet switch is a packet switch for Ethernet frames Buffering of frames prevents collisions. Each port is isolated and builds its own collision domain An Ethernet Hub does not perform buffering: Collisions occur if two frames arrive at the same time. Hub Switch

Dual Speed Ethernet hub Dual-speed hubs operate at 10 Mbps and 100 Mbps per second Conceptually these hubs operate like two Ethernet hubs separated by a bridge Dual-Speed Ethernet Hub

Routers Routers operate at the Network Layer (Layer 3) Interconnect IP networks

Gateways The term “Gateway” is used with different meanings in different contexts “Gateway” is a generic term for routers (Level 3) “Gateway” is also used for a device that interconnects different Layer 3 networks and which performs translation of protocols (“Multi-protocol router”)

Bridges versus Routers An enterprise network (e.g., university network) with a large number of local area networks (LANs) can use routers or bridges 1980s: LANs interconnection via bridges Late 1980s and early 1990s: increasingly use of routers Since mid1990s: LAN switches replace most routers

A Routed Enterprise Network Internet Router Hub FDDI FDDI

A Switched Enterprise Network Internet Router Bridge/ Switch

Example: Univ. of Virginia CS Department Network Design of the network architecture (Spring 2000) There is no router !

Interconnecting networks: Bridges versus Routers Each host’s IP address must be configured If network is reconfigured, IP addresses may need to be reassigned Routing done via RIP or OSPF Each router manipulates packet header (e.g., reduces TTL field) Bridges/LAN switches MAC addresses of hosts are hardwired No network configuration needed Routing done by learning bridge algorithm spanning tree algorithm Bridges do not manipulate frames

Bridges Overall design goal: Complete transparency “Plug-and-play” Self-configuring without hardware or software changes Bridges should not impact operation of existing LANs Three parts to understanding bridges: (1) Forwarding of Frames (2) Learning of Addresses (3) Spanning Tree Algorithm

Need for a forwarding between networks What do bridges do if some LANs are reachable only in multiple hops ? What do bridges do if the path between two LANs is not unique ?

Transparent Bridges Three principal approaches can be found: Fixed Routing Source Routing Spanning Tree Routing (IEEE 802.1d) We only discuss the last one in detail. Bridges that execute the spanning tree algorithm are called transparent bridges

(1) Frame Forwarding MAC forwarding table Each bridge maintains a MAC forwarding table Forwarding table plays the same role as the routing table of an IP router Entries have the form ( MAC address, port, age), where MAC address: host name or group address port: port number of bridge age: aging time of entry (in seconds) with interpretation: a machine with MAC address lies in direction of the port number from the bridge. The entry is age time units old. MAC address port age a0:e1:34:82:ca:34 45:6d:20:23:fe:2e 1 2 10 20 MAC forwarding table

Forward the frame on the appropriate port (1) Frame Forwarding Assume a MAC frame arrives on port x. Is MAC address of destination in forwarding table for ports A, B, or C ? Not found ? Found? Forward the frame on the appropriate port Flood the frame, i.e., send the frame on all ports except port x.

(2) Address Learning (Learning Bridges) Routing tables entries are set automatically with a simple heuristic: The source field of a frame that arrives on a port tells which hosts are reachable from this port. Src=x, Dest=y Src=x, Dest=y Src=y, Dest=x Port 1 Port 4 x is at Port 3 y is at Port 4 Port 2 Port 5 Src=x, Dest=y Src=y, Dest=x Src=x, Dest=y Port 3 Port 6

(2) Address Learning (Learning Bridges) Learning Algorithm: For each frame received, the source stores the source field in the forwarding database together with the port where the frame was received. All entries are deleted after some time (default is 15 seconds). Src=y, Dest=x Port 1 Port 4 x is at Port 3 y is at Port 4 Port 2 Port 5 Src=y, Dest=x Port 3 Port 6

Example Consider the following packets: (Src=A, Dest=F), (Src=C, Dest=A), (Src=E, Dest=C) What have the bridges learned?

Danger of Loops Consider the two LANs that are connected by two bridges. Assume host n is transmitting a frame F with unknown destination. What is happening? Bridges A and B flood the frame to LAN 2. Bridge B sees F on LAN 2 (with unknown destination), and copies the frame back to LAN 1 Bridge A does the same. The copying continues Where’s the problem? What’s the solution ? F F F F

Flooding Can Lead to Loops Switches sometimes need to broadcast frames Upon receiving a frame with an unfamiliar destination Upon receiving a frame sent to the broadcast address Broadcasting is implemented by flooding Transmitting frame out every interface … except the one where the frame arrived Flooding can lead to forwarding loops E.g., if the network contains a cycle of switches Either accidentally, or by design for higher reliability

Solution: Spanning Trees Ensure the topology has no loops Avoid using some of the links when flooding … to avoid forming a loop Spanning tree Sub-graph that covers all vertices but contains no cycles

Solution: Spanning Trees Ensure the topology has no loops Avoid using some of the links when flooding … to avoid forming a loop Spanning tree Sub-graph that covers all vertices but contains no cycles Links not in the spanning tree do not forward frames

Constructing a Spanning Tree Need a distributed algorithm Switches cooperate to build the spanning tree … and adapt automatically when failures occur Key ingredients of the algorithm Switches need to elect a “root” The switch with the smallest identifier For each of its interfaces, a switch identifies if the interface is on the shortest path from the root And it excludes an interface from the tree if not

Constructing a Spanning Tree (cont. I) root Three hops One hop

Constructing a Spanning Tree (cont. II) Use broadcast messages; e.g. (Y, d, X) From node X Claiming Y is the root And the distance from X to root is d

Steps in Spanning Tree Algorithm Initially, each switch thinks it is the root Switch sends a message out every interface identifying itself as the root Example: switch X announces (X, 0, X) Switches update their view of the root Upon receiving a message, check the root id If the new id is smaller, start viewing that switch as root Switches compute their distance from the root Add 1 to the distance received from a neighbor Identify interfaces not on a shortest path to the root … and exclude them from the spanning tree

Example From Switch #4’s Viewpoint Switch #4 thinks it is the root Sends (4, 0, 4) message to 2 and 7 Then, switch #4 hears from #2 Receives (2, 0, 2) message from 2 … and thinks that #2 is the root And realizes it is just one hop away Then, switch #4 hears from #7 Receives (2, 1, 7) from 7 And realizes this is a longer path So, prefers its own one-hop path And removes 4-7 link from the tree 1 3 5 2 4 6 7

Example From Switch #4’s Viewpoint Switch #2 hears about switch #1 Switch 2 hears (1, 1, 3) from 3 Switch 2 starts treating 1 as root And sends (1, 2, 2) to neighbors Switch #4 hears from switch #2 Switch 4 starts treating 1 as root And sends (1, 3, 4) to neighbors Switch #4 hears from switch #7 Switch 4 receives (1, 3, 7) from 7 And realizes this is a longer path So, prefers its own three-hop path And removes 4-7 Iink from the tree 1 3 5 2 4 6 7

Robust Spanning Tree Algorithm Algorithm must react to failures Failure of the root node Need to elect a new root, with the next lowest identifier Failure of other switches and links Need to recompute the spanning tree Root switch continues sending messages Periodically reannouncing itself as the root (1, 0, 1) Other switches continue forwarding messages Detecting failures through timeout (soft state!) Switch waits to hear from others Eventually times out and claims to be the root

Spanning Tree Protocol (IEEE 802.1d) The Spanning Tree Protocol (SPT) is a solution to prevent loops when forwarding frames between LANs The SPT is standardized as the IEEE 802.1d protocol The SPT organizes bridges and LANs as spanning tree in a dynamic environment Frames are forwarded only along the branches of the spanning tree Note: Trees don’t have loops Bridges that run the SPT are called transparent bridges Bridges exchange messages to configure the bridge (Configuration Bridge Protocol Data Unit or BPDUs) to build the tree.

Configuration BPDUs

What do the BPDUs do? With the help of the BPDUs, bridges can: Elect a single bridge as the root bridge. Calculate the distance of the shortest path to the root bridge Each LAN can determine a designated bridge, which is the bridge closest to the root. The designated bridge will forward packets towards the root bridge. Each bridge can determine a root port, the port that gives the best path to the root. Select ports to be included in the spanning tree.

Concepts Each bridge as a unique identifier: Bridge ID Bridge ID = Priority : 2 bytes Bridge MAC address: 6 bytes Priority is configured Bridge MAC address is lowest MAC addresses of all ports Each port of a bridge has a unique identifier (port ID). Root Bridge: The bridge with the lowest identifier is the root of the spanning tree. Root Port: Each bridge has a root port which identifies the next hop from a bridge to the root.

Concepts Root Path Cost: For each bridge, the cost of the min-cost path to the root. Designated Bridge, Designated Port: Single bridge on a LAN that provides the minimal cost path to the root for this LAN: - if two bridges have the same cost, select the one with highest priority - if the min-cost bridge has two or more ports on the LAN, select the port with the lowest identifier Note: We assume that “cost” of a path is the number of “hops”.

Steps of Spanning Tree Algorithm Each bridge is sending out BPDUs that contain the following information: The transmission of BPDUs results in the distributed computation of a spanning tree The convergence of the algorithm is very quick root ID cost bridge ID port ID root bridge (what the sender thinks it is) root path cost for sending bridge Identifies sending bridge Identifies the sending port

Ordering of Messages We define an ordering of BPDU messages We say M1 advertises a better path than M2 (“M1<<M2”) if (R1 < R2), Or (R1 == R2) and (C1 < C2), Or (R1 == R2) and (C1 == C2) and (B1 < B2), Or (R1 == R2) and (C1 == C2) and (B1 == B2) and (P1 < P2) ID R1 C1 ID B1 ID P1 ID R2 C2 ID B2 ID P2 M1 M2

Initializing the Spanning Tree Protocol Initially, all bridges assume they are the root bridge. Each bridge B sends BPDUs of this form on its LANs from each port P: Each bridge looks at the BPDUs received on all its ports and its own transmitted BPDUs. Root bridge is the smallest received root ID that has been received so far (Whenever a smaller ID arrives, the root is updated) B B P

Operations of Spanning Tree Protocol Each bridge B looks on all its ports for BPDUs that are better than its own BPDUs Suppose a bridge with BPDU: receives a “better” BPDU: Then it will update the BPDU to: However, the new BPDU is not necessarily sent out On each bridge, the port where the “best BPDU” (via relation “<<“) was received is the root port of the bridge. R1 C1 B1 P1 M1 R2 C2 B2 P2 M2 R2 C2+1 B1 P1

When to send a BPDU R Cost B x Say, B has generated a BPDU for each port x B will send this BPDU on port x only if its BPDU is better (via relation “<<“) than any BPDU that B received from port x. In this case, B also assumes that it is the designated bridge for the LAN to which the port connects And port x is the designated port of that LAN R Cost B x

Selecting the Ports for the Spanning Tree Each bridges makes a local decision which of its ports are part of the spanning tree Now B can decide which ports are in the spanning tree: B’s root port is part of the spanning tree All designated ports are part of the spanning tree All other ports are not part of the spanning tree B’s ports that are in the spanning tree will forward packets (=forwarding state) B’s ports that are not in the spanning tree will not forward packets (=blocking state)

Building the Spanning Tree Consider the network on the right. Assume that the bridges have calculated the designated ports (D) and the root ports (P) as indicated. What is the spanning tree? On each LAN, connect R ports to the D ports on this LAN

Example Assume that all bridges send out their BPDU’s once per second, and assume that all bridges send their BPDUs at the same time Assume that all bridges are turned on simultaneously at time T=0 sec.

Example: BPDU’s sent by the bridges T=0sec (1,0,1,port) sent on ports: A,B (2,0,2,port) ports A,B (3,0,3,port) ports A,B,C (5,0,5,port) ports A,B,C (6,0,6,port) ports A,B,C,D (7,0,7,port) ports A,B,C T=1sec (1,0,1,port) A,B (2,0,2,port) A,B (1,1,3,port)A,C (1,1,5,port) B,C (1,1,6,port) A,C,D (1,1,7,port) A T=2sec (1,2,2,port) none (1,1,3,port) A,C (1,1,6,port) D (1,1,7,port) In the table (1,0,1,port) means that the BPDU is (1,0,1,A) if the BPDU is sent on port A and (1,0,1,B) if it is sent on port B. At T=1, Bridge 7 receives two BPDUs from Bridge 1: (1,0,1,A) and (1,0,1,B). We assume that A is numerically smaller than B. If this is not true, then the root port of Bridge 7 changes.

Example: Settings after convergence Bridge 1 Bridge 2 Bridge 3 Bridge 5 Bridge 6 Bridge 7 Root Port - A B Designated Ports A,B A,C B,C D Blocked ports Resulting tree: