Visit for more Learning Resources

Slides:

Advertisements

Similar presentations

PROJECTIONS OF PLANES In this topic various plane figures are the objects. 1.Inclination of it’s SURFACE with one of the reference planes will be given.

Advertisements

PROJECTIONS OF SOLIDS.

Let’s make engineering more easy

Development of Surfaces.

PROJECTIONS OF PLANES Prof.T.JEYAPOOVAN

PROJECTIONS OF PLANES 1.POSSIBLE POSITIONS A.With Respect to H.P. Parallel to the H.P. Perpendicular to the H.P. Inclined to the H.P. B.With Respect to.

Points, Lines, and Planes Three Dimensional Geometry

1 NOTATIONS FOLLOWING NOTATIONS SHOULD BE FOLLOWED WHILE NAMEING DIFFERENT VIEWS IN ORTHOGRAPHIC PROJECTIONS. IT’S FRONT VIEW a’ a’ b’ OBJECT POINT A LINE.

PROJECTIONS OF PLANES In this topic various plane figures are the objects. What will be given in the problem? 1.Description of the plane figure. 2.It’s.

ISOMETRIC PROJECTIONS

C.R.ENGINEERING COLLEGE

Prisms Fun with by D. Fisher

Engineering Graphics Anna Edusat course on “Engineering Graphics ” Lecture – 4 Projections of Lines Dr. Vela Murali,Ph.D., Head and Professor i/c - Engineering.

Projection of Planes Plane figures or surfaces have only two dimensions, viz. length & breadth. They do not have thickness. A plane figure, extended if.

PROJECTIONS OF SOLIDS & SECTIONS OF SOLIDS

Isometric Projection of Solid By Alok kumar testing CIPET - Hajipur

Learning Outcomes 1. Develop and interpret the projection of regular solids like Cone, Pyramid, Prism and Cylinder.

Warm Up Classify each polygon. 1. a polygon with three congruent sides 2. a polygon with six congruent sides and six congruent angles 3. a polygon with.

Lesson 60 Geometric Solids Prisms & Cylinders. Geometric Solids right triangular prism right circular cylinder regular square pyramid right circular cone.

PAP: Perpendicular to HP and 45o to VP.

POLYGONS A polygon is a closed plane figure that has 3 or more sides.

Class Opener 1 – 18 – 12: The diagonals of a quadrilateral are perpendicular bisectors of each other. What is the name that best describes the quadrilateral?

PROJECTIONS OF SOLIDS 1.TYPES OF SOLIDS I.POLYHEDRA A solid that has all faces as flat surfaces and are polygons. A.Regular Polyhedra All faces shall be.

Projection  If straight lines are drawn from various points on the contour of an object to meet a plane, the object is said to be projected on that plane.

PROJECTIONS OF PLANES Plane surface (plane/lamina/plate)

What will be given in the problem?

SECTIONS OF SOLIDS Part II

Warm Up Classify each polygon. 1. a polygon with three congruent sides 2. a polygon with six congruent sides and six congruent angles 3. a polygon with.

UNIT-III PROJECTION OF SOLIDS Projection of Solids: A solid is a three dimensional object having length, breadth and thickness. It is Completely bounded.

ENGINEERING GRAPHICS By R.Nathan Assistant Professor Department of Mechanical Engineering C.R.ENGINEERING COLLEGE Alagarkovil, Madurai I - SEMESTER.

Design and Communication Graphics

PROJECTION OF PLANES Hareesha NG Don Bosco Institute of Technology Bangalore-74.

(1) Prism: It is a polyhedra having two equal and similar faces called its ends or bases, parallel to each other and joined by other faces which are rectangles.

ISOMETRIC DRAWINGS LECTURE NO

Visit for more Learning Resources

1.1 Points, Lines, and Planes

NOTATIONS FOLLOWING NOTATIONS SHOULD BE FOLLOWED WHILE NAMEING

What is usually asked in the problem?

May look at figures in box to give you some ideas. Geometric Solid:

Visit for more Learning Resources

COMPUTER AIDED ENGINEERING DRAWING

PROJECTIONS OF POINTS.

PROJECTION OF PLANE 08 MARKS.

Introduction to Geometry

Auxiliary Views & Development

All about Shapes.

Projection of PLANE.

Section of Solids Hareesha N Gowda Lecturer

ISOMETRIC PROJECTION RATHER DRAWING

UNIT – III Syllabus (a) Projection of planes: Introduction, types of planes, projection of planes, projection of planes perpendicular to both the reference.

UNIT – IV (a) Development of surfaces: Introduction, methods of development, development of lateral surfaces of right solids, cube, prisms, cylinders,

10-2 & 10-3: Representations of 3-D Figures and Surface Area of Prisms

SECTIONS OF SOLIDS Chapter 15

What will be given in the problem?

C.R.ENGINEERING COLLEGE

PROBLEMS INVOLVING TRACES OF THE LINE.

Cross Sections TeacherTwins©2014.

Engineering Graphics I

What will be given in the problem?

Points, Lines, and Planes

SECTIONS OF SOLIDS Part I

PROJECTIONS OF LINES, PLANES AND AUXILIARY PROJECTIONS

PROJECTION Any object has three dimensions, ie its length, width and thickness. A projection is defined as the representation of an object on a two dimension.

Projections of Solids Mohammed Umair Hamid

Orthographic Views of Solids

Laxmi Institute of Technology, sarigam

Copyright © Cengage Learning. All rights reserved.

What will be given in the problem?

Engineering Graphics I

Presentation transcript:

Visit for more Learning Resources PROJECTION OF PLANE 08 MARKS Visit for more Learning Resources

CO’S RELATED THIS CHAPTER Draw the position of line, planes, solids with reference plane

Plane surface (plane/lamina/plate) A plane is as two dimensional surface having length and breadth with negligible thickness. They are formed when any three non-collinear points are joined. Planes are bounded by straight/curved lines and may be either regular or an irregular. Regular plane surface are in which all the sides are equal. Irregular plane surface are in which the lengths of the sides are unequal. Positioning of a Plane surface A plane surface may be positioned in space with reference to the three principal planes of projection in any of the following positions: Parallel to one of the principal planes and perpendicular to the other two. Perpendicular to one of the principal planes and inclined to the other two. Inclined to all the three principal planes.

Projections of a Plane surface A: Plane surface parallel to one plane and perpendicular to the other two Figure 1. Projections of a triangular lamina on the projection planes

Figure 2. Rotation of PP and HP after projection

Figure 3. Orthographic projections of the lamina ABC

B) Plane parallel to HP and perpendicular to both VP and PP Figure 4. Projections of the lamina with its surface parallel to HO and perpendicular to both VP and PP

Plane parallel to PP and perpendicular to both HP and VP Figure 5 Projections of a pentagonal lamina with its surface parallel to PP and perpendicular to HP and VP

For more detail contact us D) Plane surface perpendicular to one plane and inclined to the other two Figure 6. The projections of the triangular lamina For more detail contact us