BullDog™ Through Casing

Slides:

Advertisements

Similar presentations

Step-by-step guide to prevent falls

Advertisements

Flanged with Opposite Side Support Installation Instructions

Drills & Drilling Drills & Drilling.

Installation. Indoor Unit Installation Typical Installation.

Drawings for an Oyster Strainer and Drain Pan This design of strainer is required in AOAC International (953.11) for use in determining the drained.

Failure Case Study of Construction at a Solid Waste Site K. Madhavan, Ph.D., P.E., Dept. of Civil & Env. Engineering Christian Brothers University Memphis,

Welcome Learn more about upcoming construction activities on Cedarvale Avenue and Oak Park Avenue View display boards and speak one-on-one with staff Building.

The Olympic Swimming Pool. Level 1. London 2012

On March 14, 2007, our Locomotive Shop staff replaced two tires on the main drive wheels of the Canadian Pacific The old tires were “sweated” off,

First installation of the BullDog™ PVC pipe-to-pipe restraint system occurred on August, Eliminated need for concrete thrust blocking Case History:

Drilling Methods Rotary rigs –Most-used method for deep production wells –Uses a fluid (mud, water or forced air) to carry drill cuttings to surface Hollow-stem.

Boring & Drilling Four general types of hand drills: –Hand drill (egg beater) –Brace –Pistol grip crank –Push (Yankee) Crank Brace Pistol Grip Crank Push.

This project was driven by a need to replace a WWII-vintage, tar coated, steel water line Case History: Florin County Water District, Sacramento, California.

The Problems with Long Bolt Flanges in process pipe connections when exposed to a fire!!

10 minute Activity Be ready to report back in ten minutes.

PIPE, FLANGE & FITTING SPECIFICATIONS. ALL METAL PIPE IS TO BE MADE OF A LONG HOLE, SURROUNDED BY METAL CONCENTRIC WITH THE HOLE. ALL PIPE IS TO BE HOLLOW.

o Existing pipe designed for gravity outfall flow – peak storm flows raise pressures above design pressure o Single gasket joint every 12’ subject to.

APPEARANCE OF THE TANK BEFORE THE COATING INSTALLATION OF THE SCAFFOLDINGS.

1 HVACR316 - Piping Related Codes Trade Math 1 Related Codes Trade Math 1.

Drilling operation to get subsurface data. Why subsurface drilling is needed? As we cant look into subsurface directly, drilling is done to bring the.

My Fault Line At Work Setefano A. Malieitulua. Water and Fault Line This is a 10” water pipe mainline break on 9400 S 1300 E. In this video at :14 seconds,

Foot binding By: Sari Kroschel.

Geometry Volume of Prisms and Cylinders. 9/11/2015 Goals Find the volume of prisms. Find the volume of cylinders. Solve problems using volume.

Investigator Casualty Guide Identifying & Assessing Damage “Looking Deeper” March 2013.

TRENCHLESS TECHNOLOGIES Submitted By:- Kamaldeep Gupta C-3.

Cutting and Swaging Tubing

1 HVACR316 - Piping Related Codes Trade Math I Related Codes Trade Math I.

Teaching Aid Invention By Stuti-G 5-E Navrachana school Sama.

Technology brought to you by. Pressure Pipe Repair & Relining Solutions using Redline Technology.

12.4 Volume of Prisms and Cylinders

San Francisco = +. Famous Landmarks San Francisco has many attractions and landmarks. In these slides I will describe many of the large landmarks and.

Copper Pipe Plumbing Systems

Minimal Path Problems Lesson Guidelines 1)Read and understand the problem. 2)Draw and label a sketch. 3)Decide which quantity is to be optimized.

2015 International Petroleum Environmental Conference

Augers, Hp & Adjustments

DRILL PRESS. 1. Belt cover 2. Speed control High speed for soft materials, such as wood. Low speed for hard materials, such as metal. 3. Chuck & chuck.

Flat Stanley visits the skateboard and bicycle park in Peachtree City, Georgia! Flat Stanley visited this cool skateboard park in Peachtree City, Georgia.

Hello again Drew! I hope you are doing well. We took Flat Stanley to the World of Coca-Cola. It is also located in Atlanta. “Coca-Cola history began in.

Automotion Parking Systems, LLC Innovative Parking Solutions.

Cold Metalworking Processes TSM 233 Unit 10. TSM 233 Metallurgy and Welding Processes Cold Metalworking Those metalworking processes where the base metals.

Thermal Multifragmentation: Experimental Study of Process Dynamics Spinodal State of Nuclear Matter Project FASA-3 Summer practice 2011, JINR Dubna.

Putnam Technical Vocational High School, Springfield, MA  Roof Water Reclamation for grey water use – Partial collection of roof water – (4)-4,000 gal.

Water Main & Sewer Contractors Serving Manhattan For Over 95 Years All Types of NYC House Sewer Connections.

Rain Shower Singapore Rain Shower Singapore Using a rain shower head in your bathroom is even more fun than it looks. Aside from the usual compliments.

Let’s Design a Box John Cobb

THE CENTRE LATHE - 'FACING OFF' A very basic operation is called ‘facing off’. A piece of steel has been placed in the chuck and the lathe cutting tool.

Hancock Golf Course Community Engagement Update. Based on the Communities feedback, the Golf Division has developed an action/work plan and will focus.

J.PRATHYUSHAG.TEJASRI DEPARTMENT OF CIVIL ENGINEERING.

Benchwork IV –Hand Taps and Hand Reamers

TRENCHLESS TECHNOLOGY

Dial Calipers Dial Calipers Introduction to Engineering DesignTM

Forging new generations of engineers

Woodworking Hand Tools.

Essay Walk I noticed… I think… Student Work

Culture is who and what we are.

ADVANTAGE BRIDGE/FRAC PLUG S

E-MAP CHAMBER PROJECT Engineering Math Advancement Program SUMMER 2006

Modern Automotive Technology PowerPoint for by Russell Krick

Spend/ cost/ take 製作人: 王滋慧老師.

Forging new generations of engineers

City Park Challenge.

Angular & Linear Velocity

Period 2 Question 1.

«ШЫҢ» оқушылар ғылыми қоғамы ЖББ М.П. Русаков атындағы

Forging new generations of engineers

Forging new generations of engineers

Recorder Post Training

Presentation transcript:

BullDog™ Through Casing City of Garland, Texas: BullDog™ Through Casing Installation of BullDog™ pipe into a casing in the Summer of 2007. Project used 6-inch, DR18, C900 pipe. Casing installation method used to minimize damage to the parking lot, above.

BullDog™ Through Casing City of Garland, Texas: BullDog™ Through Casing 16 joints of pipe installed through the casing. The first ten joints were walked in by crew. The entire push took only 35 minutes.

BullDog™ Through Casing City of Garland, Texas: BullDog™ Through Casing Bulldog Restraint System has a smaller outside diameter than traditional metallic harness restraint systems. The smaller outside diameter allows a smaller casing to be used, a less expensive auger bit, less spoil, and less time for augering the hole.