Pam Eckert ota 210 November 12, 2012

Slides:



Advertisements
Similar presentations
Unit 7 Installing Computer Hardware
Advertisements

Tenon Cork Replacement Remove all the old cork plus any residue of the old glue Use the tenon itself to measure where to cut the replacement cork strip.
ELC Graphics Units 1 Health & Safety in the Graphics Technology Room when making a business card Name:
Step #1 Wash hands using proper hand washing technique Note: please see “Hand Washing” Power Point for more details Cafeteria: Canned Fruit Prep.
Installing a double Dreamscreen. Check measurement Left.
Oxygen Administration R/C MERT Medic Assistant Lesson V.
Eric Heber May 11, Table of Contents i. Introduction i. Purpose
ICRA Panel System Installation Instructions
Typical Walk-in Closet with elfa® décor
Electronics Merit Badge Class 4 5/17/2015Electronics Merit Badge Class National Scout Jamboree1.
Safety when cutting with knives. By Fergus Evans..
Guide Craft Badge Ideas
Sewing Equipment FACS Chapter 43.
Collagraphy Materials. Base Plate The base plate is the foundation on which the artist will be applying other materials to create a collage. The base.
Teen Living Notes Competency: Basic fashion construction procedures to produce personal clothing & home accessories.
© Pearson Education Limited, Copying permitted for the purchasing institution only. This material is not copyright free. Painting and Decorating.
2006 Hand and Power Tool Safety Basic Rules for Rube Goldberg Competition,
Administration of Vaccine via Intramuscular Route
Do this now… Go to and complete the pre-lesson survey. Go to my eBoard and set up.
Reliability MANUAL CARTRIDGE UNLOAD Super DLT1 Presented By Quantum Technical Services.
Introduction to Soldering
Installing a single Dreamscreen Set unit in place and attach with 2 ½ “ screw. Do not tighten the screw yet, tighten just enough to keep from falling.
ELC Textiles - Optional Unit 15 Designing and Making a Fabric Container for Personal Possessions Work by:
Microworlds Unit Lesson Five: Learning to Use the Microscope.
ELECTRIC VEHICLE PROJECT CAR BUILDING PROCEDURES BY: PIERRE PEASHA CENTENNIAL HIGH SCHOOL BAKERSFIELD, CA.
Body Mechanics LEQ: How does using proper body mechanics prevent injury in the healthcare setting?
HOW TO MAKE YOUR OWN SOAP STEP 1  Gather the ingredients. Cold process soap is made from oils, lye and water. When these ingredients are combined at.
Textiles Technology Year 7
How To: Replace an LTR- 450R Suzuki Fuel Filter By Goigen (#11)
Installing a Strain Gage MEEN The content of this presentation is for informational purposes only and is intended only for students attending Louisiana.
Communication (With Customers and for Handling) Wayfair, LLC.
Lecture 6 Castration of animals Castration of pigs Castration, or the removal of the testicles, is carried out on the male pig which is not needed for.
SAFETY. General Safety FFFFreedom from harm or danger.
Preventing Pallet Racking Systems From Collapsing
Oxyacetylene Fusion Welding Safety Review
Object handling procedures
RE 4/3 RPC Pre-assembly manual 1. HCP case preparation
Minimizer Confidential
Fabric Art with Lights Workshop!
No Solder Battery Interrupter
I Can Show What I Know When I Gotta Go! (…to the Bathroom)
Prepared by: Gp Capt Dr. Hamid Ullah Khan Niazi
PROPERTY OF PIMA COUNTY JTED, 2010
Minimizer Confidential
KITCHEN SAFETY.
Science Sprint #2 Electricity and Magnetism
Basic Carpentry Hand Tools: Hammers
Service Procedure For Changing Engine Oil And An Oil Filter
Bellwork What does CPR stand for? 9/11/2018
Fault detection Lecture (1).
Conductivity Sensor Fabrication
How to Build a Water Bottle Rocket
Name: ___________________
Safety.
Prototyping with Sheet Metal
Horizontal Milling Operations
Most Effective Procedures to Repair a Brake Booster.
Simple Way to Install Auto Lock Door in Car
I Can Show What I Know When I Gotta Go! (…to the Bathroom)
Classroom & Laboratory Safety
Plant Pigment Chromatography Visual Instructions
CHAPTER 45 Engine Lubrication.
Ceramics Semester Fall 2016.
General Chemistry Laboratory CHE116/CHE118
Safety Practices: Cold Metal
LESSON-13 STRAIGHT KNIFE CUTTER
Fin & Countertop Sample Kit Instructions
Presented By : S.Pradeep (AP/MCT)
Kitchen Equipment Learning Target:
Metalwork Threading.
Presentation transcript:

Pam Eckert ota 210 November 12, 2012 My adaptive equipment TIOLET AIDE

Target population and purpose The elderly Provides assistance with independent hygiene Aides those with limited upper extremity ROM, reach, and dexterity This would also be idea for individuals suffering from: generalized weakness, strokes, shoulder limitations, obesity, etc.

PRECAUTIONS MAY NOT BE SUITABLE FOR PERSONS WITH LITTLE TO NO SENSATIONS IN PERI/ANEL AREA (ONE WOULD NEED TO KNOW THE AMOUNT OF PRESSURE BEING APPLIED WHEN USING DEVICE TO AVOID INJURY) WHEN USING THE DEVICE ALWAYS MAKE SURE THERE IS ENOUGH TOILET PAPER ON THE CLIP TO AVOID THE POSSIBILITY OF SCRAPING SENSITIVE AREAS ENSURE PROPER CLEANING OF DEVICE AFTER EACH USE TO AVIOD THE SPREAD OF GERMS/INFECTIONS CHECK FOR WEAR AND TEAR OF DEVICE FREQUENTLY

Materials list and cost Small paint roller $ 2.00 (discard the roller after purchase) End of an old curling iron $0.00 (preferably detachable kind) Rubber stretchy ball for handle $1.00 (optional for better grip) Screw driver (4 way) & Knife $0.00 TOTAL COST $3.00 * All items were purchased at local Dollar General Store *

Directions for Fabrication of Device STEP 1 Purchase a small paint roller and discard the roller, leaving you with just the metal portion and plastic handle STEP 2 Take the end of an old curling iron (clip end) detach and unscrew the part that was holding it on to the bottom portion or handle; keep the screws and the small plastic piece that comes off you will need them later STEP 3 Cut a small notch in the side of the plastic end of the curling iron (not the metal end) below the clips; in doing this it will allow the curling iron to fit on to the paint roller STEP 4 Slide the curling iron onto the metal end of the paint roller; now reattach the small plastic piece to the clip end with the screws. There will be some movement this is what you want. STEP 5 (OPTIONAL) for better grip Cut a small slit in a rubber stretchy ball and slide it over the plastic handle of the paint roller. Add a string to hang it up and now your own personal toilet aide is complete

Original inspired Device Self Wipe Toilet Aide Cost: $ 66.99 www.pattersonmedical.com