I can make Orthographic drawings

Slides:

Advertisements

Similar presentations

How to check close-to-the-line arrows F E D E R A T I O N I T N E R N A T I O N A L E D E T I R A L ' A R C a b TOP VIEW FRONT VIEW a b c d e c d e.

Advertisements

Technical Sketching and Drawing

Technical Drawing CHAPTER 1

Engineering Drawing ELEC 106 Fundamentals of Electrical Engineering

SURFACE AREA and VOLUME with BASE 10 BLOCKS

Laboratory 2: Introduction to AutoCAD and Microsoft Project

Orthographic Projection

Orthographic Projection Basics

The Other Side Product Design Sketching Activity.

Geometry Perspectives

Isometric Drawing. The following presentation will demonstrate how to draw isometric objects using the “box method”. Use an isometric template sheet to.

AutoCAD 2D_I Module 5: Orthographic Projection. Module Objectives identify surfaces in two-dimensional views from a given three-dimensional views. Demonstrate.

Using Drawings to Communicate. EML 2023 Computer Aided Design communicate design intent How can you sketch this angle bracket to convey its shape effectively?

Sketching Practice “One picture is worth a thousand words.”

1-1 Nets and Drawings for Visualizing Geometry

Chapter 8 Introductory Geometry Section 8.6 Viewing and Drawing Solid Figures.

Nets and Drawing for Visualizing Geometry

Chapter 1: Tools of Geometry

Orthographic Drawings

Textbook - page 10 Lined paper. Vocabulary An isometric drawing of a three dimensional object shows three sides of a figure from a corner view. Workbook.

Drawings, Nets, and Other Models Drawings, Nets, and Other Models

Make an isometric drawing of the cube structure below.

Using Drawings to Communicate Lecture 3 –How to create an isometric drawing of a part when given front, top, & right side views.

Warm-Up What 3-d geometric shape will the following nets fold to create? 1) 2) 3)

Space Figures, Nets & Diagrams Objectives:  To identify nets of space figures  To make isometric drawings of space figures.

Nets and Drawings for Visualizing Geometry

Orthographic Projection

Stem Agenda Week 8 10/15 – 10/19. Agenda 10/15  Careers Day with Ms. Benson!

Isometric Drawings & Orthographic Drawings Tutorial 5d.

IOT POLY ENGINEERING 2-19 November 29, 2010 Your drawing space is 10” wide by 7 ¼” high. Calculate the horizontal starting point and the vertical starting.

Orthographic Drawing. Today I will be learning to : Improve my graphic skills by learning how to draw an Orthographic Projection of a 3D object All: Will.

Researching Designs.

1.2 Drawings, Nets, and Other Models

Isometric & Orthographic Drawings

Nets and Drawings for Visualizing Geometry

Section 1.1 Nets and Drawings for Visualizing Geometry

Orthographic Drawings

Section 1.1 – Nets and Drawings for Visualizing Geometry

Nets and Drawings for Visualizing Geometry

Representations of Three-Dimensional Figures

Questions to Ponder 1-1 & 1-2

Review and more practice

Year 7 Graphics – Orthographic Projection

September 10, 2009 DRILL Answer the following in complete sentences:

Reading Objects Lecture 8 Instructor:

Sketching Practice Gateway To Technology®

Orthographic Projection

Technical Drawing Visual Communication of Technical Information

Isometric Projection -the term ‘isometric’ comes from the Greek for ‘equal measure’ reflecting the scale along each axis is the same - Isometric views.

Projections Orthographic drawings – drawings where three views of an object are drawn in perpendicular planes to one another.

Engineering Your Future: A Comprehensive Introduction to Engineering

Orthographic Projection

North American Natives & the Maya

ENGN103 Engineering Drawing

Orthographic Sketch Solution

ENGN103 Engineering Drawing

Multiview Drawing Orthographic Projection

Inclined Planes & Curved Surfaces

Visualizing Geometry Skill 01.

S1 Orthographic Sketching

2-D Representations of Solids

ENGN103 Engineering Drawing

Projections Orthographic drawings – drawings where three views of an object are drawn in perpendicular planes to one another.

Introduction to Orthographic Projections

Announcements for Minor-I

Area of combined shapes

Introduction to Engineering Review: Isometric Drawings

Introduction to Engineering Review: Multi-view Drawings

1.2: Drawings, Nets, and other models

Presentation transcript:

I can make Orthographic drawings

Orthographic Drawing Objective: SWBAT create and interpret orthographic drawings IOT create the 3D figures they represent.

Drill: What is wrong with the picture? 2” 4” 1” 4” 1”

Want to make $50,000?

Practice Orthographic Sketch Top 3” RUBRIC Top View – 5pts Front View – 5pts Side View – 5pts Alignment – 5pts Dimensions – 5pts 2” 6” 3” Front Side

Object Lines Projection lines Dimension lines 6” 3” 3” 2”

You try it! Letters A-C

Orthographic Sketch – A 3” RUBRIC Top View – 5pts Front View – 5pts Side View – 5pts Alignment – 5pts Dimensions – 5pts 2” 1” 6” 3”

Orthographic Sketch – B RUBRIC Top View – 5pts Front View – 5pts Side View – 5pts Alignment – 5pts Dimensions – 5pts 1” 1” 2” 1” 6” 3”

Orthographic Sketch – C RUBRIC Top View – 5pts Front View – 5pts Side View – 5pts Alignment – 5pts Dimensions – 5pts 4” 4” 4” 1” 1” 2” 8” 1” 2” 2” 12” 2” 6”

Now let’s reverse it!

Build it!

Check it!

Build it!

Check it!

Build it!

Check it!

Build it!

Check it!

Build it! 6” 2” 4” 1” 1” 2”

Report Out Going around the room you must give an original fact concerning the drawing we did today. WT

Where are we headed next class? Take your 4 blocks and stack them into whatever shape you wish. Draw the 3D shape

Isometric drawing Draw a 4 x 3 x 2 box Draw a 2 X 3 x 6 box

Build it!