Steam Generator Main Feed Pump Radial Bearing Modification

Slides:



Advertisements
Similar presentations
Steam and Water Accessories
Advertisements

Hydraulic Pumps • Hydraulic Pump Types
Boiler Operation Procedures
Furnaces also called Fired Heaters
Circulating Water System
Manchester 09/sept/2008A.Falou & P.Cornebise {LAL-Orsay}1 CALICE Meeting/ Manchester Sept 2008 SLAB Integration & Thermal Measurements.
Series I Pump and Prep Pump Prior to removing the head, rotate the flag on the top of the motor so the piston is fully retracted. Remove thumb nuts.
JET PROPULSION Part 5 Jet Engine Operation Oil Systems.
Summery of Cooling System Teflon Leaks* *This is independent of the internal problems Rob Pisani.
Shadows. Shadows occur when light shines on an object and the light does not pass through. (opaque objects)
Steam Generation Efficiency
Installation Instructions for all Inpro/Seal Company Air Mizer Series Bearing Isolators Inpro/Seal Company th Avenue West Rock Island, IL
Applications of Friction in Machines: Journal Bearings A journal bearing supplies lateral support to a rotating shaft. For example the axle on your.
2 July Turbine Condensate System
Presentation on Installation of a Domestic Cold Water Storage Cistern
In the analysis of a tilting pad thrust bearing, the following dimensions were measured: h1 = 10 mm, h2 = 5mm, L = 10 cm, B = 24 cm The shaft rotates.
Fuel/Lube Oil Systems - AND – Propulsion Train & Shaft Line Components
Feedwater Systems Reliability Users Group Annual Meeting January 20-23, 2014 Feedwater Pump Thrust Bearing Failure Presented By: Kurt J. Weis Rotating.
Hydronic Mechanical Controls
Integration and Alignment of Optical Subsystem Roy W. Esplin Dave McLain.
Final Stages NGL Separation
“Fix Tube Sheet” Heat Exchanger
Distribution and Lubrication
350, 350A 2½”-12”. Modification Overview  Production of the 2½ - 10” sizes began in  Production of the “A” models began in This Indicates.
EMISSION PROBE PARTS TUBE: 3/8” OD x wall Stainless Steel Length determined by pipe diameter and placement of connecting end to allow easy connection.
Automotive Fuel and Emissions Control Systems 3/e By James D. Halderman Copyright © 2012, 2009, 2006 Pearson Education, Inc., Upper Saddle River, NJ
Introduction Topic: Internal Gear/Lobe Pump Name: Matthew Stoangi Objective: To provide a clear understanding of the mechanics involved within an internal.
Armory of Company F and Public Library. Armory, City Hall.
The Tesla Turbine A DIY Guide. Description Modern turbines rely on principles of aerodynamics, where the air flow pushes the blades attached to an axle.
PISTON ENGINE PROPULSION Chapter 4 Oil Systems 1933 Alvis Engine 2014 Hyundai Engine Distribution and Lubrication.
1 Energy Efficient Housing. 2 Why construct energy efficient structures? Bottom Line !!! Money It may save up to 60% of the cost to heat/cool the structure.
FC Flow Control: Centrifugal pump with constant speed (rpm) Orifice plate sensor Globe valve FC Flow Control: Positive displacement pump Orifice plate.
Director’s Review of RunIIb Dzero Upgrade Installation Linda Bagby L0 Electronics Installation  System Electronics Overview u Low Voltage u High.
Mitglied der Helmholtz-Gemeinschaft Twister 15. Januar Shaft Moderators & Reflectors Radial Bearing Axial Bearing Target Rotation and lifting device.
912 sPHENIX Solenoid Test Mar STRAIN GAGES MICRO MEASUREMENTS WK BG-350: QTY 28, QTY 21 OPERATIONAL 1. TS01 STRAIN-GAGE RADIAL TIE.
NSTX Upgrade Test Cell Initial Schedule Vent vacuum vessel by 9/19 No vessel entry at this time Period of removals prior to start of outage: 9/19 – 10/14.
OILGEAR PVV PUMPS PVV 200 Performance Curves.
1 Product Presentation January Normal BinROXELL Bin Old feed Normal bin: ‘centerflow’ feed flows first in center  bridging ‘mass flow’ feed.
Starter: What is your definition of weather and how is it different from climate. 10/26/ The Great Shoe Caper 10/26/15 Practice : Climate Review.
Educational Services 1 LNN Family Split Case Pumps.
Shaft Replacement Standard Operating Procedure
Chapter 37: Fluid Containment
Fixed Orifice Tube Cycling Clutch System (FOTCC)
Fixed Orifice Tube Cycling Clutch System (FOTCC)
Installing Branch Circuits
Fixed Orifice Tube Cycling Clutch System (FOTCC)
Unit 37: Fluid containment Dr
- Condensate pump and feed pump trip!
Electrical Wiring Circuit Board Project
DYNAMIC COMPRESSORS.
Bell ringer Complete questions #1 & 2 on the Interpreting Graphs WS
Steering Systems Topics covered in this presentation:
SGFP 22 Coupling On 5/26, identified excessive concentric offset for the 22 SGFP coupling (67 mils in horizontal direction) FMEA was developed which identified.
Thermodynamics Cycles.
Product Presentation January 2010.
Govt.Engg.Collage Bhavnagar
Types of Ball Bearings Suported by.
Solving Bearing Misalignment Issues for STP Feed Pumps
Unit 37: Fluid containment Dr
Call to Fix Dell Printer Error Code
ITEMS TO CHECK ON Running Pumps
Trouble Shooting Hydraulic System Failure
بسم الله الرحمن الرحيم الموضوع:الوضوء صفته وفرائضه وسننه
Floating Head Heat Exchanger
Furnaces (also called Fired Heaters)
- Condensate pump and feed pump trip!
Causes Behind the Low Oil Pressure Lights Comes in Car.
Lecture Objectives: Finish with Sorption cooling
St. James School and Formation Center Future Parking
WELCOME TO TURBINE & ITS AUXILIARIES KNOWLEDGE GROUP PRESENTATION by madhukar srivastava, se (m), ktps, dvc.
Presentation transcript:

Steam Generator Main Feed Pump Radial Bearing Modification

Out-board Bearing

In-board Bearing

Out-board bearing cover removed The CURRENT bearing temperature detector enters the bearing in the center, east side. Oil supply inlet Original style bearing installed. Out-board bearing cover removed

In-board bearing cover removed Bearing temperature detector enters the bearing in the center, right (west) side. Oil supply inlet In-board bearing cover removed

The NEW and the OLD

New Style Tilting Pad Radial Bearings Notice that the bearings are DIRECTIONAL, and are installed in ONE direction of rotation. The new bearings have temperature detectors (RTD’s) installed INTO the bottom shoe.

NEW STYLE out-board bearing installed

RTD Lead With the new bearing installed in the correct rotational direction, the RTD leads will exit the bearing on the PUMP SIDE of the bearing and will exit the housing on the west side. Which is opposite of the original installation.

NEW STYLE in-board bearing installed

With the new bearing installed in the correct rotational direction, the RTD leads will exit the bearing on the COUPLING SIDE of the bearing. The RTD leads will go though the web of bearing saddle and will exit the housing on the west side.

Bearing RTD lead exits the in-board Bearing house on the west side. RDT lead where it exits the bearing on the coupling side, and goes through the bearing saddle.

SGFP 23

SGFP 21

The End