HAND DRAWING AN ELLIPSE

Slides:

Advertisements

Similar presentations

1. 6 Circles (Part 1) 1. Circle Notes

Advertisements

Part- I {Conic Sections}

Oblique and Isometric Drawings

Dimensioning Dimensioning Gateway To Technology®

Design & Drafting Technology Unit 4

THE ELLIPSE. The Ellipse Figure 1 is ellipse. Distance AB and CD are major and minor axes respectively. Half of the major axis struck as a radius from.

Isometric ellipses In an isometric drawing, the object is viewed at an angle, which makes circles appear as ellipses. Holes Cylinders Example object –

Module 4: Isometric Drawing

ENS 207 engineering graphics

Graphics 2: Isometric Sketching From Different View Points

OBLIQUE VIEWS Oblique drawings provide a quick way to sketch an object and represent the three dimensions of height, width and depth. Oblique drawings.

Technological Systems Unit 1 ~ How They Work Lesson 1 ~ Exploring Technological Systems Technical Sketching.

Isometric drawings (perspectives)

Solidworks Exercise Modeling the bearing block (40 minutes)

How to Sketch a Horizontal Line

GMED UNIT 1 Pictorial Drawings.

3rd Angle Orthographic Projection

ISOMETRICS Isometric means “equal in measure” and refers to the fact that the three receding axes are tilted at 30°. Isometric drawings are constructed.

Chapter 2 Using Drawing Tools & Applied Geometry.

Engineering 1182 College of Engineering Engineering Education Innovation Center Curved Surfaces in Isometric Sketches Chapter 2 of the Text.

ENTC 1110 OBLIQUE PICTORIALS.

Introduction to Projections Four Basic Types

Section Plane Through Apex Section Plane Through Generators Section Plane Parallel to end generator. Section Plane Parallel to Axis. Triangle Ellipse Parabola.

Study Lesson 5 Pictorial sketching.

F.V. and S.V.of an object are given. Draw it’s isometric view.

Geometric Constructions

Circles. Equation of a circle: ( x – h )2 )2 + ( y – k )2 )2 = r2r2 Center of the circle: C( h, k ) Radius of the circle: r Diameter of the circle: d.

Sketching an Isometric Circle © 2012 Project Lead The Way, Inc.Introduction to Engineering Design.

Introduction to Engineering Introduction to Isometric Ellipse Agenda: Sketching of ellipse for isometric drawings Introduce concepts and conventions of.

Unit 1 Drafting Standards & Techniques -Sketching.

1 SheetCourse: Engineering Graphics 1504Memorial University of Newfoundland Engineering Graphics 1504 Lecture 2 – General Sketching Objectives l Lines.

Isometric Circles.

Isometric Circle using the Ordinate Method

Preparation of Tools.

Isometric Circle using the Ordinate Method

Sketching an Isometric Circle

CURVES IN ENGINEERING.

Part- I {Conic Sections}

ITI SEMESTER 2 ENGINEERING DRAWING FITTER AND ELECTRICIAN

Cross sections of 3-D solids

ISOMETRIC PROJECTION RATHER DRAWING

Graphics 2: Isometric Sketching From Different View Points

Sketching Techniques Sketching Techniques PLTW Gateway®

Curved Surfaces in Isometric Sketches

Sketching an Isometric Circle

PDT176 COMPUTER-AIDED DRAFTING CHAPTER 5 ISOMETRIC DRAWING

Graphics 2: Isometric Sketching From Different View Points

Hyperbola - Graphing Recall that the equations for a hyperbola are ...

Sketching an Isometric Circle

Types of pictorial projection

Sketching Techniques Sketching Techniques PLTW Gateway®

Sketching Techniques Sketching Techniques PLTW Gateway®

Sketching an Isometric Circle

Sketching Techniques Sketching Techniques PLTW Gateway®

Tutorial: Flange with Equations

MENG104 ENGINEERING GRAPHICS

Are the buildings below three dimensional shapes?

Sketching an Isometric Circle

Sketching an Isometric Circle

Sketching an Isometric Circle

Chapter 5 Isometric Sketching.

Sketching Techniques Sketching Techniques PLTW Gateway®

Part- I {Conic Sections}

Part- I {Conic Sections}

Sketching an Isometric Circle

Sketching Techniques Sketching Techniques PLTW Gateway®

Title in table of contents called – Part A isometric circles

Presentation transcript:

HAND DRAWING AN ELLIPSE . Rev: 20120913, AJP Extracting Drawings

SOLIDWORKS CONSTRUCTION Start with a 4" x 4" x 4" cube Draw a centered circle with a 3" diameter on the front face.

SOLIDWORKS CONSTRUCTION Note that the circle becomes an Ellipse In the Isometric view. Cut (extrusion cut) the drawn circle through the cube

HAND SKETCHING AN ELLIPSE To create a hand drawn ellipse on the cube, first size and locate the boundary of the ellipse and then draw the diagonals as shown. 3" Draw a vertical and a horizontal line through the diagonal intersection point to create the ellipse tangent points.

HAND SKETCHING AN ELLIPSE Bisect the upper left portion of the diagonal. Bisect the remaining portion of the diagonal.

HAND SKETCHING AN ELLIPSE Repeat the process for the lower right portion of the diagonal. These “white” points will determine the boundaries for the ellipse*. Draw the arcs as shown below. * Note that the above “white” points will be at ¾(.75) of the half diagonal when the exact location = 1/(2^.5) = .7071

HAND SKETCHING AN ELLIPSE Draw the arcs as shown below. Compare Hand Drawn Ellipse with SOLIDWORKS CONSTRUCTION.