Object in front of Picture Plane

Slides:

Advertisements

Similar presentations

Craft, Design, and Technology.

Advertisements

1-Point Perspective Drawings

HLBackCurve HLFrontCurve

ENGINEERING GRAPHICS 1E7

How to draw in 1 Point Linear An Artist’s Tool for showing Space and Form.

Graphic boclair academy MEASURED PERSPECTIVE.

PROJECTIONS OF PLANES 1.POSSIBLE POSITIONS A.With Respect to H.P. Parallel to the H.P. Perpendicular to the H.P. Inclined to the H.P. B.With Respect to.

ORTHOGRAPHIC PROJECTIONS

ENGINEERING GRAPHICS 1E9

Introduction to Perspective Projection. Perspective Projection is a geometric technique used to produce a three- dimensional graphic image on a plane,

Two-Point Perspective Drawing

Lecture 9 Monday, 29 June ENGINEERING GRAPHICS 1E7 Lecture 9: Perspective.

One-point Perspective

1 Perspective Construction One point at a time. Defining the Station Point, Vanishing Point, Horizon Line, Ground Line & Projection Plane.

PERSPECTIVE PROJECTION Prof.T.JEYAPOOVAN Department of Mechanical Engineering Hindustan Institute of Technology and Science Chennai , India

TA 101 T hink and A nalyze Anupam Saxena Associate Professor Mechanical Engineering Compliant and Robotic Systems Lab Indian Institute of Technology Kanpur.

Geometry 12.1/2 Representations of 3-d Figures Surface Area of Prisms and Cylinders.

TA 101 T hink and A nalyze Anupam Saxena Associate Professor Mechanical Engineering Compliant and Robotic Systems Lab Indian Institute of Technology Kanpur.

Curves in Perspectives A room view has been drawn as a Two-point Perspective view. The room has a bookcase and a desk shown in position. Draw the circular.

1-POINT PERSPECTIVE Learning how to draw a 3- dimensional street scene.

SECTIONS OF SOLIDS Part I Prof.T.JEYAPOOVAN Department of Mechanical Engineering Hindustan Institute of Technology and Science Chennai , India

Banff Academy Technology Department Higher Graphic Communication

Unit 1 Measured Perspective Revision. Always ensure that you have positioned the plan correctly and to the correct scale.You must also draw in the correct.

Perspective Drawings Chapter Technical Drawing 13 th Edition Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart © 2009 Pearson Education,

Coatbridge High School

Perspective Drawing Techniques

Isometric Projection of Solid By Alok kumar testing CIPET - Hajipur

IT IS INTERESTING TO LEARN THE EFFECT ON THE POSITIONS OF VIEWS ( FV, TV ) OF THE OBJECT WITH RESP. TO X-Y LINE, WHEN PLACED IN DIFFERENT QUADRANTS TO.

Locating images in a Plane Mirror object mirror Image of object S - Same size as object A - upright L - behind mirror T - virtual reflected incident.

Projection  If straight lines are drawn from various points on the contour of an object to meet a plane, the object is said to be projected on that plane.

Perspective Drawing for Technical Illustration References: 11, 2, 323.

All perspective drawings start out with a horizon line (HL). The horizon line can be anywhere on your paper or even off the paper in some cases. The horizon.

Perspective Drawings 1, 2, 3, 4. All perspective drawings have a Horizon Line and vanishing points.

FOR T.V. FOR S.V. FOR F.V. FIRST ANGLE PROJECTION IN THIS METHOD, THE OBJECT IS ASSUMED TO BE SITUATED IN FIRST QUADRANT MEANS ABOVE HP & INFRONT OF.

TA 101 T hink and A nalyze Anupam Saxena Associate Professor Mechanical Engineering Compliant and Robotic Systems Lab Indian Institute of Technology Kanpur.

Mechanical Perspective This enables you to get the measurements on a perspective drawing accurate.

TA 101: Technical Arts II Dr. Prishati Raychowdhury Department of Civil Engineering IIT Kanpur Office: FB 330; Phone: 6692

Orthographic Projection Welcome Engineering Graphics - Lect.

Prospettiva ZeroSei - Curvilinear perspective: “how to draw” and examples - 5 vanishing points by Massimo Marrazzo

ПЕЧЕНЬ 9. Закладка печени в период эмбрионального развития.

TWO POINT PERSPECTIVE Object in front of Picture Plane.

PERSPECTIVE DRAWING. Step 1 Quarter the page as shown with light lines. Where the middle line touches the border mark two points - these are called....

Shawlands Academy Department Of Technical Education

Perspective Drawing Techniques

SOLID GEOMETRY.

Introduction to PROJECTION

PERSPECTIVE PROJECTIONS Mr. Y.MuraliKrishna M.Tech Department of Mechanical Engineering Geethanjali Institute of Science & Technology Nellore , A.P,

Perspective Projection Sample

Object behind Picture Plane

--the area around an object

Orientation of Point in Space

Creating 2-Point Perspective

One point perspective.

PERSPECTIVE DRAWING.

Engineering Graphics I

Vanishing Point Horizon Line X. Vanishing Point Horizon Line X.

Graphic Communication

Architectural Drawings Systems

SECTIONS OF SOLIDS Part I

TRUE LENGTH (T.L.) AND TRUE INCLINATION (T.I.)

Belmont Academy Technical Education LEFT CLICK MOUSE TO CONTINUE

ORTHOGRAPHIC PROJECTIONS { MACHINE ELEMENTS }

Introduction to Perspective Projection

Graphic Communication

Year 9 Design Perspective 2

Orthographic Views of Solids

Introduction to Orthographic Projections

Engineering Graphics I

VCD102 - Gambar Desain Desain Komunikasi VIsual

ORTHOGRAPHIC PROJECTIONS { MACHINE ELEMENTS }

Presentation transcript:

Object in front of Picture Plane TWO POINT PERSPECTIVE Object in front of Picture Plane

Revise concepts What is 2PP? Why 2PP? What do following concepts mean? VP GL SP PP HL

Object in front of PP

2 PP process Find LVP and RVP From corners of TV to SP draw lines Where these lines meet PP draw perpendicular lines Find front corner of object if needed. Draw line from front corner to GL perpendicular. Project heights from FV to front corner line Complete the parts behind the PP

Draw parts in front of picture plane

Find vanishing lines

Draw a line from the SP to the corner to the PP

Draw line from PP perpendicular over the GL

Extend the vanishing line to find the corner

Draw new points vanishing line