Structural Drafting Assignment S-3.

Slides:



Advertisements
Similar presentations
Protractor Center Hole. Measuring and Drawing Angles with a Protractor By Christine Berg Edited By V Hamilton.
Advertisements

Structural Steel Construction
Drafting – Product Design & Architecture
Engineering Graphics IV
1 of 4 LESSON #13 A REVIEW OF ORTHOGRAPHIC PROJECTION
Unit 5 Three-View Drawings
OBLIQUE VIEWS Oblique drawings provide a quick way to sketch an object and represent the three dimensions of height, width and depth. Oblique drawings.
Unit 4 Extension Lines And Dimension Lines
ENGINEERING GRAPHICS 1E7
Orthographic Projection
Auxiliary Views – An Overview
A UXILIARY V IEWS! N O, R ICHARDS! C ADD STUDENTS MUST NEVER LEARN THE TRUTH ABOUT A UXILIARY V IEWS! F ORGET IT D OOM! T HEY WILL LEARN….EVEN IF I HAVE.
Demonstrate correct drawing procedures
Multi-View Drawing (Text Chapter 8)
Structural Symbols and Conventions
1 Introduction to Engineering Dimensioning - 2 Agenda Understand the principles of good dimensioning practice Apply the standard dimensioning practices.
This is a very basic 3-view, Orthographic Projection TOP RIGHT SIDE
Engineering H191 - Drafting / CAD Gateway Engineering Education Coalition Lect 5P. 1Autumn Quarter Design Process Isometric Drawings Lecture 6.
Chapter 5 Creating and Editing Drawing Views. After completing this chapter, you will be able to perform the following: –Create base and projected drawing.
Structural Drafting Connection Details and Gages.
Step one: Page Border and title block. Border will be ¼” from the edge of the paper. Drawing will be done in landscape format. Title block will be 1”
Drawing Abilities Teacher
TECH 104 – Technical Graphics Communication Week 2: Sketching, Text, and Visualization.
Flange Plates to be Welded to Beam Flanges.
Auxiliary Views.
Alternate Views.
Reading Working Drawing Packets and Section Views
Engineering Graphics IV Prof. Jon Southen October 17, 2008.
Structural Drafting Assembly Clearance Dimensions.
British Standards BS8888.
Structural Steel Construction
1 SheetCourse: Engineering Graphics 1504Memorial University of Newfoundland Engineering Graphics 1504 Lecture 2 – General Sketching Objectives l Lines.
Working Drawings Competency: 00X.00
Measuring and Drawing Angles with a Protractor. Protractor Center Hole.
Sizing of drawing in drafting Has standard and guidelines.
PICTORIAL DRAWINGS.
What is a working drawing and what is orthographic projection?
Working Drawings Competency: 00X.00
Basic Lines and Views.
Concordia University Mechanical Engineering Drawing MECH 211/M
Multiview Sketching & Projection Chapter 5 Print handouts
FRAMING CONECTIONS Session 3.
Lines Associated with Triangles 4-3D
Engineering Graphics & Design
Hexagonal Pyramid cut at an angle #2
Mechanical Engineering Drawing MECH 211/2 Y
Forging new generations of engineers
Orthographic Projection
Isometric Projection -the term ‘isometric’ comes from the Greek for ‘equal measure’ reflecting the scale along each axis is the same - Isometric views.
Alternate Views Introduction to Engineering Design
Engineering Drawings ME 161
Structural Drafting Assignment S-4.
Auxiliary Views.
Dimensioning Dimensioning Gateway To Technology®
Alternate Views.
Orthogonal Drawings Orthogonal drawings are 2d drawings of 3d objects created by orthographic projection. Orthogonal: intersecting or lying at right angles.
Break down Lance rack Cut one of each of these for each rack
Forging new generations of engineers
In this chapter, you will learn the following:
Forging new generations of engineers
Isometric and Orthographic Projections
Print Reading.
Forging new generations of engineers
Objectives Understand the meaning of the various lines used on engineering drawings Recognize the various symbols used to convey information Read and understand.
It’s a Fine Line !.
Solidworks Computer-Aided Drafting Program LESSON 7- Angle Bracket
Dimensioning Dimensioning Gateway To Technology®
Miniature Train Smoke Stack.
Orthographic Projection
LABEL Each of your views should be labelled appropriately. Each label should be in capital letters and should be centred under each view.
Presentation transcript:

Structural Drafting Assignment S-3

Part Plan Dimensions Beam designations End reactions Title and Scale

Connection Detail Beam designations Center to Center dimension Gage outstanding leg (GOL) dimension Hole spacing dimension Assembly clearance dimension (C) Setback dimension (1/2”) Edge distance dimension for 3/4” diameter fastener Title and Scale

Shop Drawing (W12 x 35 Beam) Cope cut dimensions Hole spacing dimension Assembly clearance dimension (C) Setback dimension (1/2”) Edge distance dimension for 3/4” diameter fastener Beam length dimensions Angle dimensions Gage outstanding leg (GOL) dimension Center to Center dimension Title and Scale

Shop drawing (W18 x 60 beam) Hole spacing dimension Beam length dimensions Center to Center dimension The term Orthographic is derived from the word “orthos” meaning perpendicular or 90o

Erection Plan Beam designations Erection marks Title and Scale

Bill of Materials Each principle view has it’s own “point of sight”

General Notes

Feedback: Privacy Policy Feedback
Do Not Sell My Personal Information
About project: SlidePlayer Terms of Service

© 2025 SlidePlayer.com. Inc. All rights reserved.