Instructor: Alexander Stoytchev CprE 281: Digital Logic Instructor: Alexander Stoytchev http://www.ece.iastate.edu/~alexs/classes/
Simple Processor CprE 281: Digital Logic Iowa State University, Ames, IA Copyright © Alexander Stoytchev
Administrative Stuff Final Project (7% of your grade) Posted on the class web page (Labs section) This is due this week (during your lab)
Administrative Stuff The FINAL exam is scheduled for Thursday May 8 @ 2:15-4:15 PM It will be in this room.
Final Exam Format The exam will cover: Chapter 1 to Chapter 6, and Sections 7.1-7.2 Emphasis will be on Chapter 6 and Chapter 5 The exam will be open book and open notes (you can bring up to 5 pages of handwritten notes) plus your textbook.
Final Exam Format The exam will be out of 130 points You need 95 points to get an A It will be great if you can score more than 100 points. but you can’t roll over your extra points
Topics for the Final Exam K-maps for 2, 3, and 4 variables Multiplexers (circuits and function) Synthesis of logic functions using multiplexers Shannon’s Expansion Theorem 1’s complement and 2’s complement representation Addition and subtraction of binary numbers Circuits for adding and subtracting Serial adder Latches (circuits, behavior, timing diagrams) Flip-Flops (circuits, behavior, timing diagrams) Counters Registers
Topics for the Final Exam Synchronous Sequential Circuits FSMs Moore Machine Mealy Machines State diagrams, state tables, state-assigned tables State minimization Designing a counter Arbiter Circuits Reverse engineering a circuit ASM Charts Register Machines Bus structure and Simple Processors Something from Star Wars
How to Study for the Final Exam Form a study group Go over the slides for this class Go over the problems at the end of Ch 5 & 6 Exercise Get some sleep
Digital System Datapath circuit Control circuit To store data To manipulate data To transfer data from one part of the system to another Comprise building blocks such as registers, shift registers, counters, multipliers, decoders, encoders, adders, etc. Control circuit Controls the operation of the datapath circuit Designed as a FSM
A Simple Processor [ Figure 7.9 from the textbook ]
What are the components? [ Figure 7.9 from the textbook ]
Register R0 [ Figure 7.9 from the textbook ]
All Registers [ Figure 7.9 from the textbook ]
2-Bit Register IN1 IN0 OUT1 OUT0 1
4-Bit parallel-access shift register (this one is not used in this example) [ Figure 5.18 from the textbook ]
Tri-State Driver [ Figure 7.9 from the textbook ]
All Tri-State Drivers [ Figure 7.9 from the textbook ]
Tri-state driver (see Appendix B for more details) [ Figure 7.1 from the textbook ]
Bus Structure A way to transfer data from any register (device) to any other register (device) A set of n wires to transfer an n-bit data What if two registers write to the bus at the same time? n Bus
Figure 7.1. Tri-state driver. Also called tri-state buffer Z: High impedance state Figure 7.1. Tri-state driver. device3 device2 device1 device0 Then several devices can be connected to a single wire Note that at any time, at most one of e0, e1, e2, and e3 can be set to 1 e2 e3 e1 e0
An n-bit Tri-State Driver An n-bit tri-state buffer can be constructed using n 1-bit tri-state buffers. Input e e e e e Output
A digital system with k registers [ Figure 7.2 from the textbook ]
How to connect registers to a bus (using tri-state drivers) This shows only two 2-bit registers, but this design scales to more and larger registers. [ Figure 7.3 from the textbook ]
An alternative approach uses multiplexers to implement a bus [ Figure 7.4 from the textbook ]
An alternative approach uses multiplexers to implement a bus (eight 5-to-1 multiplexers) This requires one multiplexer per bit. Assuming 8-bit registers, we need eight 5-to-1 multiplexers. [ Figure 7.4 from the textbook ]
Adder/Subtractor [ Figure 7.9 from the textbook ]
Adder/subtractor unit y y y n – 1 1 Add ¤ Sub control x x x n – 1 1 c n -bit adder c n s s s n – 1 1 [ Figure 3.12 from the textbook ]
The first two stages of a carry-lookahead adder x 1 y g p s c 2 [ Figure 3.15 from the textbook ]
A hierarchical carry-lookahead adder Block x 15 8 – y 7 3 1 Second-level lookahead c s P G 31 24 16 32 [ Figure 3.17 from the textbook ]
Control Circuit [ Figure 7.9 from the textbook ]
Designing The Control Circuit
The function register and decoders Clock X w En y 1 2 3 2-to-4 decoder Function Register Y I FR in f Rx Ry Function [ Figure 7.11 from the textbook ]
Operations performed by this processor Function Performed Load Rx, Data Rx Data Move Rx, Ry Rx [Ry] Add Rx, Ry Rx [Rx] + [Ry] Sub Rx, Ry Rx [Rx] - [Ry] [ Table 7.1 from the textbook ]
Operations performed by this processor Function Performed Load Rx, Data Rx Data Move Rx, Ry Rx [Ry] Add Rx, Ry Rx [Rx] + [Ry] Sub Rx, Ry Rx [Rx] - [Ry] Where Rx and Ry can be one of four possible options: R0, R1, R2, and R3 [ Table 7.1 from the textbook ]
Operations performed by this processor Function Load 1 Move Add Sub Rx1 Rx0 Register R0 1 R1 R2 R3 Ry1 Ry0 Register R0 1 R1 R2 R3
Operations performed by this processor 0 1 1 1 0 0 Move R3, R0 f1 f0 Function Load 1 Move Add Sub Rx1 Rx0 Register R0 1 R1 R2 R3 Ry1 Ry0 Register R0 1 R1 R2 R3
Operations performed by this processor 1 0 0 1 1 1 Add R1, R3 f1 f0 Function Load 1 Move Add Sub Rx1 Rx0 Register R0 1 R1 R2 R3 Ry1 Ry0 Register R0 1 R1 R2 R3
Operations performed by this processor 1 1 0 0 1 0 Sub R0, R2 f1 f0 Function Load 1 Move Add Sub Rx1 Rx0 Register R0 1 R1 R2 R3 Ry1 Ry0 Register R0 1 R1 R2 R3
Operations performed by this processor 0 0 1 0 x x Load R2, Data f1 f0 Function Load 1 Move Add Sub Rx1 Rx0 Register R0 1 R1 R2 R3 Ry1 Ry0 Register R0 1 R1 R2 R3
Similar Encoding is Used by Modern Chips [http://en.wikipedia.org/wiki/Instruction_set]
Sample Assembly Language Program For This Processor Move R3, R0 Add R1, R3 Sub R0, R2 Load R2, Data
Machine Language vs Assembly Language Meaning / Interpretation 011100 100111 110010 001000 Move R3, R0 Add R1, R3 Sub R0, R2 Load R2, Data R3 [R0] R1 [R1] + [R3] R0 [R0] – [R2] R2 Data
Machine Language vs Assembly Language Meaning / Interpretation 011100 100111 110010 001000 Move R3, R0 Add R1, R3 Sub R0, R2 Load R2, Data R3 [R0] R1 [R1] + [R3] R0 [R0] – [R2] R2 Data
Machine Language vs Assembly Language Meaning / Interpretation 011100 100111 110010 001000 Move R3, R0 Add R1, R3 Sub R0, R2 Load R2, Data R3 [R0] R1 [R1] + [R3] R0 [R0] – [R2] R2 Data For short, each line can be expresses as a hexadecimal number
Machine Language vs Assembly Language Meaning / Interpretation 1C 27 32 08 Move R3, R0 Add R1, R3 Sub R0, R2 Load R2, Data R3 [R0] R1 [R1] + [R3] R0 [R0] – [R2] R2 Data
Intel 8086 [http://en.wikipedia.org/wiki/Intel_8086]
Intel 8086 Memory Address [http://en.wikipedia.org/wiki/Intel_8086]
Intel 8086 Machine Language [http://en.wikipedia.org/wiki/Intel_8086]
Intel 8086 Assembly Language [http://en.wikipedia.org/wiki/Intel_8086]
Intel 8086 Comments [http://en.wikipedia.org/wiki/Intel_8086]
Control signals asserted in each time step (Load): I0 Extern Rin = X Done (Move): I1 Rin = X Rout = Y (Add): I2 Rout = X Ain Gin AddSub = 0 Gout (Sub): I3 AddSub = 1 [ Table 7.2 from the textbook ]
Control signals asserted in each time step (Load): I0 Extern Rin = X Done (Move): I1 Rin = X Rout = Y (Add): I2 Rout = X Ain Gin AddSub = 0 Gout (Sub): I3 AddSub = 1 1 clock cycle 3 clock cycles [ Table 7.2 from the textbook ]
A part of the control circuit for the processor Reset Up-counter Clear w En y 1 2 3 T 2-to-4 decoder Q Clock [ Figure 7.10 from the textbook ]
What are the components? Reset Up-counter Clear w En y 1 2 3 T 2-to-4 decoder Q Clock [ Figure 7.10 from the textbook ]
2-Bit Up-Counter T y 2-to-4 decoder w En Q Clock Up-counter Clear Reset Up-counter Clear w En y 1 2 3 T 2-to-4 decoder Q Clock [ Figure 7.10 from the textbook ]
2-bit Synchronous Up-Counter Q Clock 1 Clear_n
2-bit Synchronous Up-Counter with Enable Q Clock Enable Clear_n
2-to-4 Decoder with Enable Input Reset Up-counter Clear w En y 1 2 3 T 2-to-4 decoder Q Clock [ Figure 7.10 from the textbook ]
2-to-4 Decoder with an Enable Input [ Figure 4.13c from the textbook ]
2-to-4 Decoder with an Enable Input 1 (always enabled in this example) [ Figure 4.13c from the textbook ]
In Chapter 6 we looked at the following Register Swap Example
Register Swap Controller [ Figure 6.10 from the textbook ]
Register Swap Controller Design a Moore machine control circuit for swapping the contents of registers R1 and R2 by using R3 as a temporary. [ Figure 6.10 from the textbook ]
If an output is not given, then assume that it is 0. State Diagram D: R 3 out 1 = in Done , w C: 2 B: A: No Transfer Reset If an output is not given, then assume that it is 0. [ Figure 6.11 from the textbook ]
Animated Register Swap
Animated Register Swap 0xFF 0x42 0xC9 These are the original values of the 8-bit registers
Animated Register Swap 1 0xFF 0x42 0xC9 For clarity, only inputs that are equal to 1 will be shown.
Animated Register Swap 1 0xFF 1 0x42 1 0xC9
Animated Register Swap 1 0xFF 1 0x42 0x42 1 0xC9
Animated Register Swap 1 0xFF 1 0x42 1 0x42
Animated Register Swap 1 1 0xFF 1 0x42 0x42
Animated Register Swap 1 1 0xFF 1 0x42 0xFF 0x42
Animated Register Swap 1 1 0xFF 1 0xFF 0x42
Animated Register Swap 1 1 0xFF 0xFF 1 0x42
Animated Register Swap 1 1 0xFF 0xFF 0x42 1 0x42
Animated Register Swap 1 1 0x42 0xFF 1 0x42
Animated Register Swap 0x42 0xFF 1 0x42
If an output is not given, then assume that it is 0. State Diagram D: R 3 out 1 = in Done , w C: 2 B: A: No Transfer Reset If an output is not given, then assume that it is 0. [ Figure 6.11 from the textbook ]
Encoding #1: A=00, B=01, C=10, D=11 (Uses Two Flip-Flops)
y1 y2 y1 y2 y1 y2 Present Next state state Outputs A 00 1 B 01 10 C 11 1 B 01 10 C 11 D w = 0 w = 1 y2y1 Y2Y1 Y2Y1 R1out R1in R2out R2in R3out R3in Done
Encoding #3: A=0001, B=0010, C=0100, D=1000 (One-Hot Encoding – Uses Four Flip-Flops)
Let's Complete the Circuit Diagram R1out = R2in = y3 R2out = R3in = y2 R1in = R3out = Done = y4 D Q Y 2 1 w Clock y 3 4 Y1 = w y1 + y4 Y2 = w y1 Y3 = y2 Y4 = y3
Implementing the States with a Counter
Control signals asserted in each time step (Load): I0 Extern Rin = X Done (Move): I1 Rin = X Rout = Y (Add): I2 Rout = X Ain Gin AddSub = 0 Gout (Sub): I3 AddSub = 1 [ Table 7.2 from the textbook ]
Derivation of the Control Inputs See pages 434- and 435 in the textbook
Arithmetic Logic Unit (ALU)
Arithmetic Logic Unit (ALU) Arithmetic Logic Unit (ALU) computes arithmetic or logic functions Example: A four-function ALU has two selection bits S1 S0 (also called OpCode) to specify the function 00 (ADD), 01 (SUB), 10 (AND), 11 (OR) Then the following set up will work S1 S0 Function ADD 1 SUB AND OR 00 01 10 11 ADD A B MUX A SUB A B A L U AND A B Result Result B OR A B Symbol S1 S0 S1 S0 (OpCode)
An Alternative Design of Four-Function ALU The previous design is not very efficient as it uses an adder and a subtractor circuit We can design an add/subtract unit as discussed earlier Then we can design a logical unit (AND and OR) separately Then select appropriate output as result What are the control signals, Add/Sub, Select0, and Select1? Add/Sub 1 ADD/SUB A B MUX S1 S0 Function ADD 1 SUB AND OR AND A B 1 MUX Result OR A B Select0 Select1
A Digital System that Implements a Simple Processor For this ALU, A+B if AddSub=1 A-B if AddSub=0 [ Figure 7.9 from the textbook ]
Examples of Some Famous Microprocessors
Intel's 4004 Chip [http://en.wikipedia.org/wiki/Intel_4004]
Technical specifications Maximum clock speed was 740 kHz Instruction cycle time: 10.8 µs (8 clock cycles / instruction cycle) Instruction execution time 1 or 2 instruction cycles (10.8 or 21.6 µs), 46300 to 92600 instructions per second Built using 2,300 transistors [http://en.wikipedia.org/wiki/Intel_4004]
Technical specifications Separate program and data storage. The 4004, with its need to keep pin count down, used a single multiplexed 4-bit bus for transferring: 12-bit addresses 8-bit instructions 4-bit data words Instruction set contained 46 instructions (of which 41 were 8 bits wide and 5 were 16 bits wide) Register set contained 16 registers of 4 bits each Internal subroutine stack, 3 levels deep. [http://en.wikipedia.org/wiki/Intel_4004]
[http://en.wikipedia.org/wiki/Intel_4004]
[http://en.wikipedia.org/wiki/Intel_4004]
Intel's 8086 Chip [http://en.wikipedia.org/wiki/Intel_8086]
[http://en.wikipedia.org/wiki/Intel_8086]
Simplified block diagram of Intel 8088 (a variant of 8086); 1=main registers; 2=segment registers and IP; 3=address adder; 4=internal address bus; 5=instruction queue; 6=control unit (very simplified!); 7=bus interface; 8=internal databus; 9=ALU; 10/11/12=external address/ data/control bus. [http://en.wikipedia.org/wiki/Intel_8086]
Questions?
THE END