©Paul Godin Updated August 2007

Slides:



Advertisements
Similar presentations
Breadboard Power bus + (red) and – (blue) on left and right of breadboard abcde (green) are all connected in a row fghij (yellow) are all connected in.
Advertisements

Interfacing Lab Part Guide. The Solderless Breadboard Rows along the top and bottom are connected horizontally along the length of the board Holes in.
Amplifying Signals Breadboarding: from a diagram to an actual working amplifier.
555 Timer ©Paul Godin Updated February Oscillators ◊We have looked at simple oscillator designs using an inverter, and had a brief look at crystal.
Introduction to electronics lab ENGRI 1810 Using: Solderless prototype board (white board) Digital multimeter (DMM) Power Supply Signal Generator Oscilloscope.
Electric Guitar Controls D. Hunt Southern Wells Jr-Sr High School
MICROCONTROLLERS MODULE 2 Programming, Controlling and Monitoring.
Living with the Lab Using Your Arduino, Breadboard and Multimeter EAS 199A Fall 2011 Work in teams of two!
© red ©
1 Hands-on: Heater Circuit Kit includes: 3 9 Volt batteries (for flight only) 1 Perf Board 3Ceramic Resistors (4 5W) 39 V connectors 1 White wire 1.
Electrical Engineering 1 WISE Investments Electrical Engineering Lab Digital Logic Laboratory Dr. Keith Holbert.
Design a Voltmeter Experiment 19. Goal Design a circuit that displays the value of unknown voltage between certain voltage ranges. – The unknown voltage.
Using Your Arduino, Breadboard and Multimeter Work in teams of two! living with the lab 1 © 2012 David Hall.
555 Timer ©Paul Godin Updated February Oscillators ◊We have looked at simple oscillator designs using an inverter, and had a brief look at crystal.
1 DC ELECTRICAL CIRCUITS ELECTRONIC TRAINER AND BREADBOARDING.
Electrical Power Distribution in America % Coal 20.4% Nuclear 20.3% Natural Gas 6% Hydro Electric 3.4% Other
Engineering H192 - Computer Programming Gateway Engineering Education Coalition Lab 2P. 1Winter Quarter Digital Electronics Lab 2.
Lab 3 page 1 ENT-DIGI-210 Lab 3 Notes ©Paul Godin Updated September 2007.
Waveform 2.1 Basic Digital Waveforms 2 Measurement Paul Godin Updated October 2009.
1 Applied Control Systems Technology. 2 Pin configuration Applied Control Systems.
TLC5940 controller / 16 RGB LEDs Eric Moore 1/25/2009 ~druid/balloon/ Files and image of circuit ALL PIN NUMBERS ARE SIMPLIFIED.
Circuits Lab ENGR 1181 Lab #3. Circuits in the Real World Many engineering fields and products require the use of circuits. Some are more complicated.
Practice Problems to become familiar with circuits and circuit diagrams.
TS 1.1 Basic Digital Troubleshooting 1 ©Paul Godin Updated August 2013 gmail.com.
Experiments Day 1 Resistors.. Electronic Technology Definition: The technology of using small amounts of electricity for controlling, detecting, collecting,
First, let’s review the structure and use of a breadboard.
Circuits Lab Introduction
Basic Digital Logic 2 Combinational Logic
Physics 2225: Working With Electronic Equipment Purpose  Learn how to use basic electronic equipment: Digital multi meter Oscilloscope Function generator.
Microprocessors Tutorial 1: Arduino Basics
How an NPN Transistor Works
Step 1. Place IC on board. Leave one empty row below IC.
Welcome to Week 4 at the Summer Computer Club Raspberry Pi (contd)
ENG241/ Lab #11 ENG2410 Digital Design LAB #1 Introduction Combinational Logic Design.
GRAPHING RELATIONSHIPS For each graph, determine the graphing relationship and record it on a white board.
Lab 2 page 1 ENT-DIGI-210 Lab 2 Notes ©Paul Godin Updated September 2007.
INTERNET OF EVERYTHING SDU 2016 Week 4. Simple Digital and Analog Inputs  The Arduino’s ability to sense digital and analog inputs allows it to respond.
Transistors to Gates © 2011 Project Lead The Way, Inc.Magic of Electrons.
How to Build a Digital Physical System - Lab Lecture 2.
Electronic Instrumentation Project 204 Project Name: Light Level Monitor Student #1: Name ID Student #2: Name ID Student #3: Name ID.
Controlling an LED with a switch. 2 breadboard place where you can build electric circuits really quickly the magical breadboard.
TITLE: 555 Timer OM INSTITUTE OF TECHNOLOGY Subject: Analog Electronics ( ) Semester: 03 Prepared By:
1 Transistor. 2 Transistors are used to turn components on and off They come in all different shapes and sizes.
Lab1 page1 BXST-DIGI-252 Lab 1 Notes ©Paul Godin Updated December 2014.
Building Circuits.
Arduino Uno – controlling LED strips
Microcontroller basics
Introduction to Handshaking Communication with SSC-32U
Wiring the Breadboard (the right way).
Simple LED circuit.
Basic Digital Logic.
Introduction to Handshaking Communication with SSC-32
LAB #1 Introduction Combinational Logic Design
© T Madas.
Visual Instructions.
Circuits Lab Introduction
Digital Electronics Lab 2 Instructor:
Colours.
Transistors to Gates Transistors to Gates Gateway To Technology
Introduction to Wiring Logic Gates
Using Slope Intercept Form to Graph Day 2
What Color is it?.
How a PNP Transistor Works
How an NPN Transistor Works
CTY SAR FCPS Shawn Lupoli, Elliot Tan
Arduino Motor Lab Inspired by NYU ITP project
CTY SAR FCPS Shawn Lupoli, Elliot Tan
Lab 1 Components List.
Using Slope Intercept Form to Graph Day 2
2019 Investing Now Summer Program
Presentation transcript:

©Paul Godin Updated August 2007 ENT-DIGI-210 Lab 1 Notes ©Paul Godin Updated August 2007

Vulcan Logic Trainer Jack for power adapter Clock post Probe post Power Switch Switch bank Probe LED Clock LED Connections for Switches Breadboard or Experimenter’s Board

Vulcan Logic Trainer Bar LEDs Variable Resistors for Clock Connections for Bar LEDs +5V Ground Horizontal bus (red & blue) Vertical buses (red & blue)

Breadboard Internal Wiring

Resource information: Layout of the breadboard

Wire Configuration END Probe = Yellow Clock Output = Green +5 Volt = Red Ground = Black END

Feedback: Privacy Policy Feedback
Do Not Sell My Personal Information
About project: SlidePlayer Terms of Service

© 2025 SlidePlayer.com. Inc. All rights reserved.