Auxiliary Pump Drive Option Replacement for D0S3002CX03

Slides:



Advertisements
Similar presentations
Build Your Own Future RC2 Serviceability. Build Your Own Future Safety and Ground Rules Before servicing, always remove A/C power from the unit and disconnect.
Advertisements

Intermediate Small Engine Maintenance and Repair Projects
OFD 1 Oli Durney LBTI Optical Engineer Steward Observatory University of Arizona NIC Aperture, Pupil, and Filter Wheel Positions Rev. 3.3 November 3, 2011.
OFD 1 Oli Durney LBTI Optical Engineer Steward Observatory University of Arizona NIC Aperture, Pupil, and Filter Wheel Positions Rev. 2.3 September 19,
Presented by: Piston Pumps PVplus. Model max. Displacement [cm³/U] Speed [min-1] PV PV PV PV PV PV
Engineer Training Inkjet Head Cleaning TJ8300 / TJ8500 Inkjet Head Cleaning.
ROFI – Next Generation – DAREL By Mike Pluma. Objectives For New Design: – Main objective: move toward Dynamic Balance Raise center of gravity by moving.
MTF SLIT COMPONENTS Adjusting Blocks and Mounting Plate Steel Blocks
Team Xerox Progress Report Mechanical Engineering Design Team Mechanical Engineering Design Team Jeff Carpenter Charlie Morris David Postel Jeremy Ryatt.
Assembly of Conductivity Flow Loop EAS 199B living with the lab (in preparation for calibrating conductivity sensor)
Ultrasonic Probe Manipulator Group:Chris Weisheim Tim Pommer Rishi Govalakrishnan Alan Koers Mentor: Dr. Jie Chen Sponsor: IU Medical School Department.
TT Assembly Structure Reference-Reinforcement System: 1.Description of the system 2.Assembling Procedure 3.Production Project Board, march 2005 D.Orlandi.
Ken YoussefiMechanical Engineering Dept., SJSU 1 Introduction to Fundamentals of Assembly.
POWER TAKE OFF’s 5 5 Engine Dependent: 1. Engine mounted
Distribution and Lubrication
Investigating Fluid Power Rig Operating instructions (c) 2012 Mechanical Kits Ltd.
AIDA 1 Mezzanine board Contacts for underside connectors Thermal contact pads.
PISTON ENGINE PROPULSION Chapter 4 Oil Systems 1933 Alvis Engine 2014 Hyundai Engine Distribution and Lubrication.
IOT POLY ENGINEERING 2-15 January 25, 2010 Pass in your Line Weight Practice Get out the following: –Timeline project handout –Orthographic Projection.
Delta II 7925H - 10L Baseline workup Launch Vehicle TheirsOurs Delta II 7925H Launch Vehicle 10L Composite Fairing 10L Stretch Composite Payload Fairing.
Dmitry Gudkov BE-RF-PM CLIC Module Working Group Engineering design of the adjustable supporting system for DBQ.
Current Status of Pepperpot Emittance Measurement System Simon Jolly Imperial College FETS Meeting, 22/02/06.
IRMOS Diffraction Grating Integral Tab Design  Performance of an optical system is highly sensitive to the surface distortion of the optics in the system.
Side view of generator. Close up of unused grounding pad - gives provisions for mounting the absorber.
ENGINE REASSEMBLY Chapter 12 Classroom Manual page 311
Gas Spring Baseplate Mount Hose-less Baseplate Hosed Baseplate Comparison Gas Spring Baseplate Mount.
InventorCAM Milling Training Course 2.5D Milling.
Motor Mounting MECH1200 Foot Mount: Simple and common Tabs or feet that are attached at the four corners of the motor and attaches to a bedplate. Sometimes.
Cold Magnetic Shield Assembly Nik Templeton 25/08/2015.
Progress on the Prototype design Catania Goikoetxea, Mikel Navarro Medrano, Javier Mainz, March 31st,
Rotating System Students: DINESH JOSHI RAJNISH VERMA RAMDEEN BISHNOI
XR621 Drive Hose Update Kit. Removal Turn off Battery dis Drain hydraulic tank Remove both rubber lines under chassis and discard. Remove and discard.
Time Remaining 20:00.
Chiho Wang ATLAS TRT Duke University IU, Oct Fuse Box Design & Mounting Chiho Wang Duke University.
New Support Structure 4x4 Beams Existing Stairs per Mr Walter Kellner Cherenkov 32 deg shifted back 4.0 inches to clear existing structure Cherenkov 40.
Prototype Cryomodule FDR Ken Premo 21 – 22 January 2015 High Power Coupler Design.
STEP 1: ASSEMBLE INSERT PLATES 1.Assemble insert plates by press fitting roller bearing and adapter plate into assembly 1.1 Prep all mating surfaces to.
Single Module Vertical Outlet Tube Change
2017 Single Module Beta to LP Changes
CYLINDER BLOCK GROUP FIG 101
Instructions for Diaphragm Replacement Cat. Nos. 2052B-01, 2054B-01
Activity 1.2.5a Mechanical Efficiency
Investigating Fluid Power Rig
Report on construction of LP2 spaceframe endplate
FRESCA2 Update on the dipole design and new calculations
Activity 1.2.5a Mechanical Efficiency
Activity 1.2.5a Mechanical Efficiency Winch Construction Guide
C Air Compressor Up-fit and Plumbing Guide For LDI B3
Info. For CEAF Heated Breather Tube Change Engines: QSB4. 5/6
SHMS Downstream Beamline Large SHMS/HMS Angles (Config-1)
Changing the orientation of the adjusting link within CF Options to resolve interference issue Options Impacted: CF , CF , CF , CF ,
Additional Upstream Coil Shielding
Activity 1.2.5a Mechanical Efficiency Winch Construction Guide
Affected Options: BR Option; EB Option; PH Option;
2017 X15 EH Bracket Machining Change
Plant issue list A108: Need WR for missing C/S on high mount FA options Chuck Crowder.
GLAST Large Area Telescope:
Dee1 View from back of back plate
Fuel Filter Option Change for D0S3002CX03
Additional Upstream Coil Shielding
VPCR OVERVIEW The banjo fitting, from Cummins ISL16 330, is not oriented to install the remote fuel filter. As shown in the picture #1(next slide), the.
NISSAN Z31 & Z32 OIL PUMP DIFFERENCES
Removal of salon doors on 1968 Roamer Sedan.
Four Jaw Collimator.
10. If Two items are selected simultaneously a second time… Terminate the session, replace all items and begin a new presentation session If the client.
Presentation transcript:

Auxiliary Pump Drive Option Replacement for D0S3002CX03 Jarrett Cathey 9/16/2016 Confidential

Background Engine Configuration: D0S3002CX03 New Auxiliary Pump Drive option (HD2051) created Two Pump Orientations: Previous option (HD2047) orientation: 43 deg. away from block or vertical New orientation which rotates pump: 53 deg. towards block or vertical

Product Comparison HD2047: HD2051:

Product Comparison (Cont.) Adapter Plate and Bracket design have changed. All other hardware/piece parts and the adapter assembly will remain the same. Thickness of the adapter plate and number of threads on the mounting holes remains the same.

Assembly

Replacement Applications previously using HD2047 should now use HD2051 and use the 43 deg. away from block or vertical orientation