FLOTEX CALGARY FLOCKED TILES & SHEETING

INTRODUCTION Flotex Flocked Flooring is a completely unique textile flooring that combines the hard wearing and durable characteristics of a resilient floor with the quality, warmth and comfort of a carpet Flotex consits of a solid vinyl reinforced base layer into which a densely flocked surface of nylon 6.6. fibres are firmly anchored Flotex is extremely dimensionally stable and has the optics of a textile floor covering, whilst being as functional and durable (as well as easy to clean) as any resilient floor covering. Flotex is available in both sheet and tile format Flotex is a choice, not a compromise

INTRODUCTION The anti-microbial sanitized® treatment on Flotex ensures consistent protection against bacteria without degeneration through cleaning or vacuuming It also suppresses the growth of dust mite populations Therefore Flotex has a positive impact on the lives of allergy sufferers even more as daily vacuuming cleans away twice as many allergens compared to conventional carpets This is why Flotex carries the British Allergy Foundation seal of approval Flotex Calgary offers a choice of colours in a soft, natural design that can easily be combined with other complementary Flotex or resilient ranges Calgary is the perfect choice for application areas that require a subtle ambiance Flotex Calgary is available in sheeting and tile form No pattern repeat

BENEFITS FLOTEX CALGARY_ Over 70 million nylon 6.6 fibres per m² Flotex holds allergens and dust to the floor and releases them when vacuumed Approved by the British Allergy Foundation Treated with a Sanitized® antimicrobial which gives protection against mould, bacteria and odours Flotex provides up to 20dB impact sound reduction Impervious backing suitable for wet cleaning Flotex is slip resistant both when wet and dry

INSTALLATION Flotex must be installed in accordance with the manufacturer’s recommendations Sub-floors must be level, smooth, hard, clean and dry before laying commences Uneven, solid or suspended timber floors may need additional preparation to meet the required standard Where there is direct to-earth concrete it is essential that an effective damp-proof membrane be incorporated Prior to installation, Flotex must be allowed to relax for 24 hours at a uniform room temperature of between 18°C and 27°C All sub-floors must be tested for acceptable moisture content in accordance with SANS 10070 prior to the commencement of installation Note that excessive moisture in the sub-floor will react adversely with the adhesive during the curing period

INSTALLATION The recommended adhesive is FloorworX No. 62 acrylic adhesive Install with arrows all pointing in the same direction Whenever possible, run the arrows toward the main light source Install sheets running lengthwise in corridors DO NOT REVERSE sheets for seaming Butt factory trimmed edges Smooth the seams DO NOT use a stretcher or knee kicker on Flotex Trim the excess material at doorways and walls using a carpet knife or edge trimmer with a hooked blade, and use a bolster to press Flotex firmly into the adhesive after trimming

SUGGESTED SPECIFICATION Supply and fix 4.3mm thick x 2.0m wide Flotex electrostatically flocked textile sheeting or 5.3mm thick x 500mm x 500mm Flotex electrostatically flocked textile tiles, manufactured in accordance with EN 1307 and laid, in accordance with manufacturer’s instructions, in FloorworX No. 62 acrylic adhesive which has been spread using a trowel fitted with an A2 notched blade at a rate of between 5.5m2 and 6.5m2 per litre on a previously prepared Class 1 sub-floor in accordance with SANS 10070, using FloorworX Self Leveller when required, including all cutting and waste The flooring must be rolled in both directions with an articulated 68kg three-sectional roller immediately after it has been laid into the adhesive. Joins must be tightly butted.

WARRANTY FloorworX offers a 5 year limited warranty, subject to our terms and conditions, against defective material provided that it is installed and maintained in accordance with our recommendations

MAINTENANCE PREVENTIVE_ Approximately 80% of the dirt and soiling that has to be cleaned off a floor has been trafficked in from outside the building More than 90% of that soiling can be avoided by the use of an effective entrance matting system. When less dirt is trafficked through the entrance there will be a reduction in maintenance requirements Regular cleaning is more cost-effective and hygienic than occasional heavy-duty cleaning Wipe up any grease and oil spills immediately and treat stains as soon as they are observed Black rubber wheels and rubber furniture feet can discolour the floorcovering. Hard plastic is preferred. Always follow the manufacturer’s dosage instructions regarding the use of cleaning chemicals.

POST-INSTALLATION SITE CLEAN_ MAINTENANCE POST-INSTALLATION SITE CLEAN_ Floor maintenance begins immediately after the completion of installation The initial step is to remove any loose dirt or debris using a dry mop, broom or vacuum Sand, construction debris and sharp-edged objects may result in irreparable damage being inflicted to the new floor Remove any visible adhesive residue using a damp cloth. Once the adhesive has cured it will be difficult to remove If other trades are working in the building after the installation of the flooring, the floor must be protected from subsequent damage by the use of thick paper, cardboard or hard board No wet maintenance must take place until 72 hours (3 days) have elapsed from the time of installation (this is to ensure that the adhesive has sufficient time to cure properly and develop full bond strength)

MAINTENANCE INITIAL CLEAN_ Vacuum the floor using an upright vacuum cleaner fitted with a powered brush Remove stains or spills using clean warm water, in conjunction with a diluted neutral carpet detergent if required, working from the outside of the stain or spill inwards When a detergent is used, ensure that the area is rinsed thoroughly with clean water to remove any residual detergent Remove excess water using a wet/dry vacuum Allow the floor to dry before permitting foot traffic

MAINTENANCE REGULAR CLEANING_ Vacuum the floor daily using an upright vacuum cleaner fitted with a powered brush Wet clean using a hot water/spray extraction carpet cleaning machine Rinse thoroughly with clean water to remove any residual detergent Remove excess water using a wet/dry vacuum Allow the floor to dry before permitting foot traffic Remove spills and stains as soon as they occur

OCCASSIONAL CLEANING_ MAINTENANCE OCCASSIONAL CLEANING_ Soak stains by spraying with a solution of mild detergent Scrub using a hot water/spray extraction carpet cleaning machine Rinse thoroughly with clean water to remove any residual detergent Remove excess water using a wet/dry vacuum Allow the floor to dry before permitting foot traffic