Structures and Mechanisms

Slides:

Advertisements

Similar presentations

Finite Element Analysis of the Steel Horse Rear Suspension Presented by: Erika Ramirez April 29, 2003.

Advertisements

FEA of Vehicle Front Stabilizer Bar & Airfoil Design (Final Project) Name: Antonio Sevilla & Sanh Si Course: ME 272 FEA Professor: Jose Granda Date:

Preloaded anchors (WP 1.4 background document presentation) Institute of Steel Structures Aristotle Univ. of Thessaloniki.

Final Project “Investigation of Head Impact during an Inverted Drop Test” ME /18/06 Luke Gibbons.

ANKLE PROSTHETIC FOR THE LOWER LEG AMPUTEE TRIATHLETE DURING THE SWIM/TRANSITION EVENT Hello and good afternoon, my name is David Lyle. I am a licensed.

ES 246 Project: Effective Properties of Planar Composites under Plastic Deformation.

Reproduction interdite © ALMA EUROPEAN CONSORTIUM Reproduction forbidden Design, Manufacture, Transport and Integration in Chile of ALMA Antennas Page.

Update on ARIES-CS Coil Structural Analysis X.R. Wang and A.R. Raffray ARIES Meeting PPPL, NJ October 4-5, 2006.

GLAST LAT ProjectDOE/NASA Mechanical Systems Peer Review, March 27, 2003 Document: LAT-PR-0XXXX Section 7.1 Stress Analysis 1 GLAST Large Area Telescope:

Parameteres thickness= Boost: 4.5g’s * shelf 1: 4540kg 2: 1588kg 3: 680kg 4: 4536kg surface: 12400kg Parafoil Deployment: 4g’s * surface: 12400kg.

PHOENIX MARS LANDER

Failure Theories Why do parts fail? What kind of stresses?

ENGR 220 Section

Unit 3: Solid mechanics An Introduction to Mechanical Engineering: Part Two Solid mechanics Learning summary By the end of this chapter you should have.

Shear Flow Built-up Members

Finite Element Analysis of Mini Baja Frame Ariana L. Gonzalez April 29, 2003 MECE.

The Stress-Velocity Relationship

General Motors Tutor Presentation : Peter Foss Project Supervisor : Professor Ahmad Barari Faculty of Engineering & Applied Science University of Ontario.

1 ME 323 Final Lecture – April 2011 Additional Topics.

Wind Turbine Support Structure

Kanwalpreet Kaur Communication subsystem & Integration subsystem.

Oregon State University Solar Vehicle Team

Thermodynamic Work consumed during Manufacturing Processes P M V Subbarao Professor Mechanical Engineering Department I I T Delhi Estimation of manufacturing.

Redesign of the STOL CH 701 Landing Gear Strut

AAE450 Spring 2009 Finite Element Analysis (FEA) for Orbital Transfer Vehicle (OTV) Tim Rebold STRC [Tim Rebold] [STRC] [1]

Mechanics of Materials, 5e Chapter 1 Tension, Compression, and Shear.

05/04/05 FEM Analysis of PA 44 Engine Mount PIPER SEMINOLE –PA-44 TWIN ENGINE AIRCRAFT.

Features: 1. 2D structural analysis (plane stress) 2. Static analysis 3. Quarter symmetric 4. SI units 5. Only the yoke is modeled 6. Material properties.

Failure Criteria and stress concentration

The City College of New York Department of Mechanical Engineering Assembly and Analysis of Collectors Edition Chevy Impala Group Members: Dave Maharaj.

Finite Element Analysis of the18 Turn Beam H. F. Fan November 5, 2004.

Mechanical Design of ROAR Krystal Mike, Ira A. Fulton School of Engineering Dr. Phil Christensen, Mentor, School of Earth and Space Exploration Arizona.

FEM Analysis of the Stage3 Support Frame H.M. Fan March 14, 2007.

Stresses and Deformations in 14 T Nb 3 Sn Solenoid of 0.8 m I.R. and 1.0 m O.R. & Half Length Bob Weggel 10/7/10.

Chapter 1 Introduction Concept of Stress. Road Map: Statics  Mechanics of Materials  Elasticity  Plasticity Fracture Mechanics Fatigue Creep Mechanics.

Analysis of TF Load Paths and Vacuum Vessel Loading H. M. Fan Jan. 22, 2009.

Practice Problems for Axisymmetric Planar Elements Jake Blanchard Fall 2007.

Weekly Report Sept. 19 th -Sept. 23 rd Federico Viscarra Sept. 23 rd, 2011 Davila research group.

NSTX TF outer leg analysis Because the stress on umbrella structure is too high, there are some ideas to reduce it, like adding a case to enhance the stiffness.

Statics and Mechanics of Materials First Edition Ferdinand P. Beer E. Russell Johnston, Jr. John T. DeWolf David M. Mazurek CHAPTER © 2011 The McGraw-Hill.

16 T dipole in common coil configuration: mechanical design

From: Tonic Finite Element Model of the Lower Limb

Lagouge TARTIBU KWANDA Mechanical Engineering

Aerospace System Prototyping and Validation- Lecture 2

From: Finite Element Modeling of Optic Nerve Head Biomechanics

Date of download: 11/6/2017 Copyright © ASME. All rights reserved.

Theories of Failure Failure of a member is defined as one of two conditions. 1. Fracture of the material of which the member is made. This type of failure.

EuroCirCol: 16T dipole based on common coils

16 T dipole in common coil configuration: mechanical design

Date of download: 12/20/2017 Copyright © ASME. All rights reserved.

Chapter 1 Introduction Concept of Stress.

Theories of Failure Failure of a member is defined as one of two conditions. 1. Fracture of the material of which the member is made. This type of failure.

Stress Analysis of Universal Tilt Kit Attachment Points

DEPARTMENT OF MECHANICAL AND MANUFACTURING ENGINEERING

Hokiesat Side Panel Analysis

التعامل مع ضغوطات العمل إعداد وتقديم إقبال المطيري

Equilibrium Of a Rigid Body.

Kevin Dahya Critical Design Review 3/6/01

Fig. 1 Finite element model and calculations.

قوانين برگزاري مناقصات و آيين نامه مالي و معاملاتي دانشگاه علوم پزشكي و خدمات بهداشتي ،درماني تهران

EML 2023 – Stress Analysis Lecture 1 – Stress State.

Protective Crane Design

An Investigation into the Failure of Belly Dump Trailers

Goods services. goods services Identify the basic questions all economic systems address Objective Identify the basic questions all economic.

Mechanics of Materials Engr 350 – Lecture 39 What’s On the Final Exam?

Table 5. Maximum stress, strain and deformation values

Transverse Shear Objective:

Formulas = Test redo for Full credit!

Presentation transcript:

Structures and Mechanisms Constructed of 6061-T6 Aluminum and 6Al-4V Titanium Four-legged square-shaped body Able to withstand 5.5g’s upon launch Able to withstand impact force upon landing 797,600 N

Structures and Mechanisms Finite Element Analysis of Vertical Member of Lander Body Using Von Mises Max Stress Criterion FS=8.8

Structures and Mechanisms Finite Element Analysis of Vertical Member of Lander Body Using Von Mises Max Stress Criterion FS=1.3

Structures and Mechanisms Finite Element Analysis of Landing Leg Strut Using Von Mises Max Stress Criterion FS=3.1