Set the composition of the initial fluid on the Basis pane.

Slides:

Advertisements

Similar presentations

Reaction Rates What affects the rate of reaction?.

Advertisements

Review Problems. Water can be made from hydrogen and oxygen: H 2 (g) + O 2 (g) → H 2 O (g) Some experiments are run in a sealed 1 L flask at 350 K to.

Excess-Limiting Reaction Practice 2 Al + 6 HCl  2 AlCl H 2 25 g of aluminum are reacted with 75 g of hydrochloric acid, what mass of hydrogen gas.

Model water-rock interaction Enter your initial fluid composition on the Basis pane, then go to the Reactants pane to create a reaction path. Titrate in.

Simulation lasts 30 years Aquifer is 70% Quartz Specify domain’s starting fluid composition on the Initial pane Initial fluid in equilibrium with Quartz.

Picking up calculation results. After performing a calculation, React can “pick up” the results and use them for a new calculation. You can pick up an.

Enter your fluid composition on the Basis pane. SpecE8 figures concentrations of aqueous and sorbed species, mineral saturation, and gas fugacity. Go to.

Types of Reactions. The symbols A, B, C and D can be used to represent ions, atoms or compounds (we’ll use them like variables in math)

A _________ is a substance that speeds up a chemical reaction without being permanently consumed in the reaction. catalyst.

Enter your initial fluid composition on the Basis pane, then go to the Reactants pane to create a reaction path. Choose the type of kinetic reaction.

Fluid 1: Cold, oxygenated seawater T = 4 °C Specify fluid composition and T on the Basis pane Run → Go to equilibrate the fluid Add new species.

X1t models reactive transport in groundwater flows in one linear or radial coordinate. Set initial fluid composition and mass of sorbing mineral Fe(OH)

Custom Rate Laws. Use the built-in rate law, or click + to select other options. Set either a rate constant, or a pre-exponential factor and an activation.

Specify chemical composition of fluid and formation minerals from the Initial pane. Set initial temperatureSet starting and ending times.

Molecular Reaction Dynamics. Collision Theory of Kinetics With few exceptions, the reaction rate increases with increasing temperature temperature If.

Decouple reaction between carbonate and Benzene(aq), other forms of carbon. Config → Redox Couples… Default setting: all redox reactions are coupled.

General Form of Built-in Rate Law r is the mineral’s dissolution rate (mol s –1 ) A s is the surface area of the mineral (cm 2 ) k + is the intrinsic.

Kinetics. Definition Kinetics is the study of reaction rates Reaction Rate is the speed of reaction Reaction rate is measured as the change in concentration.

Mr. Quinn & Ms. TomFebruary 6, 2014 Aim: How do we predict the amount of product formed in a chemical reaction? Do Now: balance the following chemical.

Kinetic reactions React, X1t, and X2t can trace several types of reactions according to kinetic rate laws: Mineral precipitation and dissolution. Redox.

Config→ Redox couples… Decouple redox pairs for electron donating and accepting half reactions.

Decouple reaction between carbonate and acetate, carbonate and methane, and sulfate and sulfide. Config → Redox Couples… Default setting: all redox reactions.

Set the initial fluid composition on the Basis pane. Dilute fluid, pH 5 Click to add components to the fluid.

Chain together kinetic reactions

Specify kinetic rate laws for mineral precipitation and dissolution (and other reaction types) on the Reactants pane. Use Arrhenius equation to calculate.

Enter your fluid composition on the Basis pane

File → Open → Thermo Data…

Date of download: 11/5/2017 Copyright © ASME. All rights reserved.

Config → Redox Couples…

Integrated Rate Law.

Unit 6 – Lesson 1 Chemical Reactions.

Chapter 11 Matter and Change 11.1 Describing Chemical Reactions

Reaction Rates Notes#12 Chapter 17.

Chemical Kinetics – collision theory

Solutions and Kinetics Test Review

Config→ Redox couples…

Set the simulation’s duration

Chemical Kinetics – collision theory

Specify domain’s starting fluid composition on the Initial pane

Set the initial fluid composition on the Basis pane.

X position (m) I s o t p i c m n C , d a y Bulk fluid CO (aq)

Chain together kinetic reactions

Unit 6 – Lesson 1 Chemical Reactions.

Nitrate Ion Concentrations

Set the composition of the initial fluid on the Basis pane.

Specify domain’s starting fluid composition on the Initial pane

Default setting: all redox reactions are coupled.

React traces reaction paths involving fluids, minerals, gases, and microbes.

Chemical Reactions.

Config → Redox couples… Decouple redox pairs for electron donating and accepting half reactions.

Equilibrium Calculations

Config → Redox couples… Decouple redox pairs for electron donating and accepting half reactions.

Equilibrium Calculations

Nitrate Ion Concentrations

Integrated Rate Law.

Specify fluid composition and T on the Basis pane

Set the chemical composition of initial system on the Basis pane.

Choose the type of kinetic reaction

Chapter 11 Matter and Change 11.1 Describing Chemical Reactions

Chemical Kinetics Method of Initial Rates

Chapter 11 Matter and Change 11.1 Describing Chemical Reactions

Law of Conservation of Mass

Topic: Chemical Reactions

Rate Affecting Factors

Unit 4: Solutions and Kinetics

Specify fluid composition and T on the Basis pane

Integrated Rate Law.

Config→ Redox couples…

Run → Go equilibrates the fluid

Chemical kinetics: Introduction : The branch of physical chemistry which deal with the study of rate of reaction, mechanisam of reaction,and various factors.

Presentation transcript:

Set the composition of the initial fluid on the Basis pane. Bulk composition of initial fluid Set the simulation’s duration

add → Kinetic → Aqueous complex… AlF++ Set up a kinetic rate law on the Reactants pane. add → Kinetic → Aqueous complex… AlF++

Supply kinetic parameters Initial concentration of the complex Rate constant Al+++ and F− ions promote the rate of reaction

Uncheck to disable precipitation We’ll simplify this example by ignoring precipitation and a few complexes of aluminum and fluoride. Config → Iteration… Config → Suppress… Uncheck to disable precipitation

Al+++ and F− react to form AlF++ complex