How to configure PC Controlled Camera Control 09.12.2004 PC Controlled Cam. Control

This presentation is intended to guide the installer step by step through the camera control installation. 09.12.2004 PC Controlled Cam. Control

PC controlled DCN system with Camera Control Direct Camera Control With Allegiant Video Switcher 09.12.2004 PC Controlled Cam. Control

Direct Camera Control (PC Controlled) Requirements : One Dome Camera CCU with TCB4 One monitor DCN software V9.30 or higher!!! DCN Control PC = Temporary Installation PC Software LBB3588/00 V2.0 or higher!!! 09.12.2004 PC Controlled Cam. Control

Step 1 Connect PC and Monitor to Dome Camera AutoDome Camera RS232 DCN Control PC with one Comport 09.12.2004 PC Controlled Cam. Control

Step 2 Install virtual keyboard software LTC 5138/00 Program AutoDome Camera RS232 DCN Control PC with one Comport 09.12.2004 PC Controlled Cam. Control

Step 3 Configure Virtual Keyboard 09.12.2004 PC Controlled Cam. Control

PC Controlled Cam. Control 09.12.2004 PC Controlled Cam. Control

Make sure you choose the right camera!! 09.12.2004 PC Controlled Cam. Control

PC Controlled Cam. Control 09.12.2004 PC Controlled Cam. Control

PC Controlled Cam. Control 09.12.2004 PC Controlled Cam. Control

PC Controlled Cam. Control 09.12.2004 PC Controlled Cam. Control

Step 4 Set Pre-Positions 09.12.2004 PC Controlled Cam. Control

PC Controlled Cam. Control 09.12.2004 PC Controlled Cam. Control

Repeat Step 4 to set all Pre-Positions Set the highest Pre-Position as overview 09.12.2004 PC Controlled Cam. Control

Step 5 Check the Pre-Positions 09.12.2004 PC Controlled Cam. Control

First make sure that the pre-positions are set. If you were not successful setting up the pre-positions please don’t continue with the next steps. First make sure that the pre-positions are set. 09.12.2004 PC Controlled Cam. Control

Step 6 Connect CCU to DCN Control PC and AutoDome Port 1 RS232 DCN Control PC DCN CCU Port 2 AutoDome Camera 09.12.2004 PC Controlled Cam. Control

Step 7 CCU protocol and Serial Port settings LBB3500/15 & LBB3500/35 Make sure that the ports of the CCU are set correct. Port 1 Protocol = Full Baudrate = 115.2K Port 2 Protocol = Camera Control Baudrate = 9.6K Keep in mind !! You have to change the baudrate of Port 2 to 9.6K !! 09.12.2004 PC Controlled Cam. Control

Step 8 Start Camera Control Software LBB3588 09.12.2004 PC Controlled Cam. Control

Keep in mind !! An installation file must be open before camera installation is possible. 09.12.2004 PC Controlled Cam. Control

Step 9 Combine seat numbers with camera pre positions 09.12.2004 PC Controlled Cam. Control

Keep in mind !! Make sure you choose the right camera!! Camera nr = Camera Address 09.12.2004 PC Controlled Cam. Control

PC Controlled Cam. Control 09.12.2004 PC Controlled Cam. Control

5 09.12.2004 PC Controlled Cam. Control

End of Installation © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. 09.12.2004 PC Controlled Cam. Control

With use of Allegiant Video Switcher (PC Controlled DCN) Requirements : Allegiant switcher Video Switcher keyboard Fixed and/or AutoDome cameras Monitor(s) DCN software V8.00 or higher DCN Control PC with two Comports Software LBB3588 V1.0 or higher 09.12.2004 PC Controlled Cam. Control

Step 1 Connect Camera(s),Monitor(s) and Keyboard to Video Switcher 09.12.2004 PC Controlled Cam. Control

Step 2 Connect CCU to Allegiant Switcher and DCN Control PC Port 1 RS232 DCN Control PC DCN CCU Port 2 Allegiant Switcher 09.12.2004 PC Controlled Cam. Control

Step 3 CCU protocol and Serial Port settings LBB3500/15 & LBB3500/35 Make sure that the following settings are chosen: Port 1 Protocol = Full Baudrate = 115.2K Port 2 Protocol = Camera Control Baudrate = 19.2K Keep in mind !! These are the default settings for the LBB3500/15 &LBB3500/35 09.12.2004 PC Controlled Cam. Control

Step 4 Start Camera Control Software LBB3588 09.12.2004 PC Controlled Cam. Control

Keep in mind !! An installation file must be open before camera installation is possible. 09.12.2004 PC Controlled Cam. Control

Step 5 Set Pre-Positions using the Video Switcher Keyboard 09.12.2004 PC Controlled Cam. Control

Step 6 Combine seat numbers with camera pre positions 09.12.2004 PC Controlled Cam. Control

PC Controlled Cam. Control 09.12.2004 PC Controlled Cam. Control

5 09.12.2004 PC Controlled Cam. Control

How to configure PC Controlled Camera Control End of section  Robert Bosch GmbH All rights are reserved. Reproduction or passing on to third parties in whole or in parts is prohibited without the written consent of the copyright owner. 09.12.2004 PC Controlled Cam. Control