Resetting and long beep test for PCB without digital display

Slides:

Advertisements

Similar presentations

Discrete Control Logic 1. Pneumatic circuits - Low forces - Discrete, fixed travel distances - Rotational or reciprocating motion Main components: compressor,

Advertisements

In this presentation you will:

ELCT 301 Dr. Enrico Santi Equipment Testing & Troubleshooting Procedure © Prepared by: Rizwan Muzaffar.

World AC/DC Power Supply Line Neutral Earth Line Neutral Ground USB 4-20mA interface RF Sen Open + - Fill Level DisplaymA Out Display + - (A)Acquired Signal(S)

Clean Air Box Usage & Care CABs RAMs CO Monitors.

1 Electronics and Control Technology. 2 Electronics and Control The 555 timer is an 8-Pin D.I.L. Integrated Circuit or ‘chip’ What it looks like Notch.

ENGR 101: Robotics Lecture 1 – Introduction Outline  The Scribbler's Sensors  Demo Modes  Graphical Programming References 

Copier Jam Detector Design Problem

Dr. Hoganson CSIS HC11 Demo Program This is our first lab using the 68HC11 microcontroller. We will “talk” to the microcontroller from a PC, run.

Introduction ► Scope:- Service Diagnostics Routines can use for XXL, Side by Side products with STEALTH user interface with single evaporator fan product.

RT 408 Repairing manual. Chapter one The whole machine problems.

1 Applied Control Systems Technology. 2 Pin configuration Applied Control Systems.

1 4-Integrating Peripherals in Embedded Systems (cont.)

SAMSUNG Washing Machine

Engineering 1040: Mechanisms & Electric Circuits Winter 2015 Interfacing Light-Emitting Diodes (LEDs) & Push Buttons to Microcontrollers.

CPO Science Workshop: The CPO Timer Integrated Physics and Chemistry.

© 2010 Akula LLC, Jeremy R. Hertzberg, BS CMPE Switches and Relays Electro-mechanical transistor.

Introduction The goal of this project was to create device similar to a DJ mixing board. Features: Controlling the input and output buffers Applying sound.

SIMON Presented By: Amanda Buczkowski James Jenkins Fadi Hanna.

IMetos Wireless sensor Networks. Definitions I : Radio WAP(W ireless A ccess P oint ) The WAP is the radio interface needed to command the iMetos3 radio.

Working “Control any electrical device with your T.V remote(any brand)” wizardelectronics.weebly.com.

Copyright © 2007 Heathkit Company, Inc. All Rights Reserved PC Fundamentals Presentation 32 – Video System Troubleshooting.

IP Different types of wave © Oxford University Press 2011 Different types of wave.

NMR loading procedure. load button needs to be held to continually supply air to the sample chamber If the air is not on the sample will drop.

IKart -- Resume the Battery form Fault 1 If the Battery overdischarges the BCS board will drive a soft shutdown of the iKart motherboard. Chances are that.

Arduino libraries Datatekniker Udvidet hardware/software.

Copier Jam Detector Design Problem

Introduction to the DE0 Board Prof. Taeweon Suh Computer Science & Engineering Korea University COSE221, COMP211 Computer Logic Design.

:Blink Blink: Er. Sahil Khanna

SERVICE TRAINING EXPERT ALPHASTAR 1132 © MAO-SE-TC 1132_SE_EX_Handout_EN_12_  Collision protection switch  Collision protection switch retrofit.

Arduino “Getting Started” Instructor : Dr Matthew Miss Khin Yi Kyaw

Electronic Instrumentation Project 204 Project Name: Light Level Monitor Student #1: Name ID Student #2: Name ID Student #3: Name ID.

Discrete Control Logic

shift to the Test Mode (Forced Operation).

WELCOME TO EVM WITH VVPAT TRAINING FOR ARO’S and STAFF

ELECTRONIC VOTING MACHINE (EVM)

"This document can not be used without Samsung's authorization"

MyQ Home Bridge Wi-Fi setup and transfer devices for Wi-Fi GDO

COMP211 Computer Logic Design Introduction to the DE2 Board

Brother Support Ireland Toll-Free Number:

How to Fix HP Computer When it Emits an LED or Beep Code?

What is the Procedure to Reset Lexmark Laser Printer.

Canon Customer Support First you need to turn on your Printer. Press & hold the “Reset button” on the printer. While pressing the “Reset.

HOW TO RESET BROTHER PRINTER HL 2250DN Quick step up Guide to reset your Brother Printer HL 2250DN

Call to Fix Canon Pixma MX340 printer Error 5200

Call to fix Samsung Printer Error Code u1 2320

Call to Fix Brother Printer in Error State

Call to Fix Epson Printer Error Code 0x97

सोलर पॅनेलचा उपयोग करुन रीचर्जेबल टॉर्च बनवणे.

Front panel wiring PICO 155

Logic Gates Practical Objective: to develop an understanding of logic circuits and truth tables.

Learning Outcomes List all Edison’s Sensors and actions

Game Controller Lesson Three.

Copier Jam Detector Design Problem

Game Controller Lesson Two.

Lego EV3 Mindstorms SW Programming Blocks.

PowerPoint Triggers ICTGAMES.TK Previous Next.

Lab 1. Introduction to the DE2 Board

Making) Melody timer.

2. ATP INITIALIZATION PLACE ATP SWITCH TO “1” OR “NORMAL” POSITION A

Arduino Uno circuit basics

Bharat Electronics

Interface ckt for demo Outputs Inputs V PIN 0 10K PIN 4 GND GND

1 If a Delegate wishes to request to take the floor, please press the black button located to the right of the microphone ONLY ONCE. A red light will.

Click “Execute” button.

Presentation transcript:

Resetting and long beep test for PCB without digital display Step for resetting and long beep: Connect the PCB with machine. Switch on the machine from power supply board. Do not switch on the power button of PCB. Ensure there should not be water and cloth load in machine. Press program (SW3) and process (SW4) button simultaneously and wait. 3 program LED will simultaneously blink along with 6 small beep sound. At the end one long beep sound will come and machine gets off. Press the power button and then press start button and keep it pressed. After 6 rotation of pulsator fuzzy light should glow. Applicable Models Digi Pacific, Digi Atlantic, Digi Rainbow, Digi Wave, Digi Aqua, KF-6011, KF-6511 Process and program button to be pressed simultaneously

Resetting and long beep test for DIGI SPRING PCB with digital display Step for resetting and long beep: Connect the PCB with machine. Switch on the machine from power supply board. Ensure that there should not be water or clothe load in machine. It should be empty. Press power and water level (WL) button simultaneously and wait. Machine will be silent for 6 sec and display will show dr. At the end long beep sound will come and machine gets off. Press the power button and then press start button and keep it pressed. After 6 rotation of pulsator fuzzy light should glow. Applicable Models Digi Spring Power and water level button to be press simultaneously