Exam Revision 100 Questions

Blacksmiths Tongs Long Handled Pliers 1.What is the correct name for this tool? End Cutters Diagonal Cutters Engineers Pliers

2. Which of the following images shows a Tee Hinge?

3.What is the correct name for the joint shown on the left Bridle Joint Cross halving Joint Rebate Joint Mortise and Tenon joint Dovetail Joint Through Housing Joint DowelJoint

5. What do the Vernier callipers shown below read? 10.2mm 5.6mm 3.4mm 3.6mm

6. On the diagram above indicate the dial that makes the blade move in and out. (The blade adjustment nut )

Block Plane Smoothing Plane Jack Plane Rebate plane 6. What is the correct name for this plane?… Bull Nose Plane Shoulder Plane Compass Plane Try Plane

Rebate Chamfer Groove Tongue 7. What is the correct name for a square notch cut along the side of a board?

Tensol Cement Cascamite 8. What is the most suitable adhesive for gluing Plastic Laminate to a Kitchen Worktop Epoxy Resin PVA Impact Adhesive

9..Where on the graph would you find the 50 th percentile?

Tensol Cement Cascamite 10. What is the most suitable adhesive to glue together this chest of drawers? Epoxy Resin PVA Impact Adhesive

Tensol Cement Cascamite 11. What is the most suitable adhesive to glue together acrylic? Epoxy Resin PVA Impact Adhesive

12. What is the correct name for the wood tool shown below? Parting tool Gouge Scraper Skew Chisel

13. On the Lathe above, where is the Chuck?

Because it has a low melting point Because it is Non Ferrous Because it is lightweight Because it melts quickly 14. Why is aluminium the most suitable material for casting in the school workshop?

15. On the diagram to The left where is the Countersink

16.What is the correct name for the machine shown above Strip Heater Vacuum Former Oven Fluidising Tank

17) On the diagram above indicate the Drag

18. What is the correct name for the type of tool shown below? Parting tool Knife ToolRoughing tool

19.What is the correct name for the rivets shown above? Countersunk rivets Snap Head Rivets Blind Rivets Pop Rivets

20.Where on the graph would you find the 95 th percentile?

Vent Spike Rammer Gate Cutter Sprue Pin 21. What is the correct name for this tool? Draw Pin Rapping Iron Striking Off Rod Cope

22. What is the missing size from the cutting list below End Click on the correct answer from the choices below

23. On the Lathe above, where is theToolpost?

24. Where is the Compound Slide?

25. Which of the images above shows a Countersunk Wood Screw?

26. What is the correct name for the tool shown below Riveter Rivet Punch Rivet Set & Snap Rivet Bar

27. What is a hand countersink used for? Removing Burrs Drilling Holes Centre Punching Holes

28) On the diagram above indicate the Cope

29. Which of the following images shows a Butt Hinge?

30. State one safety precaution you would take when turning large diameter work on the wood lathe? Slow the lathe down Speed the lathe up

31. On the image above which tool is a Die

32. What is the correct name for the wood tool shown below? Parting tool Gouge Scraper Skew Chisel

33. Which drawing shows a Blind Hole

34. On the image above which tool is the Plug Tap

35. Which metal is most suited to casting in the school workshop? Brass SteelCopper Aluminium

36. What is the correct name for this tool? End Cutters Tinsnips Shears Pliers

37. What is the correct name for the joint shown on the left Bridle Joint Cross halving Joint Rebate Joint Mortise and Tenon joint Dovetail Joint Through Housing Joint DowelJoint

38. Which of the following tools would be used to cut 6mm Dia steel bar? A Panel Saw A Coping SawA Piercing saw A Jnr Hacksaw

Tensol Cement Cascamite 39. What is the most suitable adhesive to glue together this garden bench? Epoxy Resin PVA Impact Adhesive

40. What is another name for Mole Grips? Long nose Pliers Engineers Pliers Self Grip Pliers Plumbers Wrench Stillson

41.What is the correct name for the scaled wooden figure often used by designers ? Ergonomics Ergonome Aesthetic Gardengnome

42. Which of the following planes would be used to plane a long uneven edge? A Block Plane A Smoothing PlaneA Jack Plane A Try Plane

43. What is the missing size from the cutting list below Base Click on the correct answer from the choices below

44. Where is the Forked Centre ?

It can grip round objects like pipe It is easier to use It has been drop forged It is cheaper to buy 45. What major advantage does a Stillson Wrench have over an Adjustable Spanner?

46. What is the correct name for this tool? Jewellers Snips Tin Snips Diagonal Cutters Heavy Duty Snips

47. Which tool is designed to cut rivets? Engineers Pliers Long Nose Pliers Diagonal CuttersEnd Cutters

48. Which of the above pictures shows the pattern with the correct taper?

The study of sensory values, The Study of the human body in its working environment 49. What does Ergonomics mean? The study of the dimensions of the human body

50. Where on the graph would you find the 5 th percentile?

51. What is the correct name for the drill bits shown on the left Twist Drills Forstner bits Flat Bits Masonry Bits Centre drills

52. What is the correct name for the machine shown above Strip Heater Vacuum Former Oven Fluidising Tank

53. Which machine was used to make the chocolate box inserts shown on the left? Strip Heater Vacuum Former Oven Fluidising Tank

54.What is the correct name for the process of coating Mild steel in molten Zinc Galvanizing Anodising Painting Plastic dip coating

55. What is the correct name for the joint shown on the left Bridle Joint Cross halving Joint Rebate Joint Mortise and Tenon joint Dovetail Joint Through Housing Joint DowelJoint

The study of sensory values, The Study of the human body in its working environment 56. What does Anthropometrics mean? The study of the dimensions of the human body

57. What is the missing size from the cutting list below Side Click on the correct answer from the choices below

58. Where is the Revolving Centre?

59. What is the correct name for the joint shown above Bridle Joint Rebate Joint Mortise and Tenon joint Dovetail Joint Through Housing Joint Dowel Joint

60.What is the correct name for the machine shown above Strip Heater Vacuum Former Oven Fluidising Tank

61.Which of the images above shows a Round Head Wood Screw?

62.What is the correct name for the joint shown above Bridle Joint Rebate Joint Mortise and Tenon joint Dovetail Joint Through Housing Joint Dowel Joint

63. What is the generic name for these fixings? Connecting Blocks Knock down fittings Connectors Bolts

64. Where is the Headstock?

65. What is the correct name for the wood tool shown below? Parting tool Gouge Scraper Skew Chisel

66. What is the correct name for the rivets shown above? Countersunk rivets Snap Head Rivets Pop Rivets

67. Which tool is designed for working in tight areas and cutting fine wire? Engineers Pliers Long Nose Pliers Diagonal CuttersEnd Cutters

68. Which of the following images shows a PianoHinge?

69. Which of the following metals is Ferrous (Contains Iron) Aluminium Copper BrassStainless Steel

70. Which of the following metals is an Alloy Aluminium Copper Brass Lead

71. Which of the following woodscrews will Rust if exposed to the rain Steel BrassStainless Steel

Line Weight 72. Which of the following terms would not be classed as Aesthetic? Form Shape Proportion Size Colour

Centre Punches Parallel Punches Letter Punches 73. What is the correct name for these tools? Nail Punches

Steel Brass Aluminium 74. What is Brazing Rod made from? Copper

75. Which of the following planes would be used to level off the base of a through housing joint.

76. Letter stamps can be used to stamp letters on which of the following? High Speed Steel Aluminium Acrylic Perspex

77. What is the correct name for the joint shown above Bridle Joint Cross halving Joint Rebate Joint Mortise and Tenon joint Dovetail Joint Through Housing Joint Dowel Joint

78. What is the correct name for the process used to coat the handle of the trowel with plastic? Galvanizing Anodising Painting Plastic dip coating

The Toolmakers clamp can be used to hold small pieces of work while it is being brazed The Toolmakers clamp can be used to hold small pieces of work while working on them 79. What are Toolmakers clamps used for? The Toolmakers clamp can be used to hold small pieces of work while it is being welded

Repousse Hammer Pillar Drill Parallel Punch Centre Punch 80. Which tool could be used to create this dimpled pattern on the back of this drawer handle? Cross Pein Hammer

81. Which of the following tools would be used to cut 0.5mm thick Copper Sheet? A Panel Saw A Coping SawTin Snips Engineers Pliers

82. Which metalwork technique is illustrated in the pictures below Drilling Facing Tapering Knurling

83. What is the correct name for the process shown below Brazing Forging Welding Casting Turning

84. On the image above which tool is a Tap

85. What is the correct name for the process shown below Brazing Forging Welding Casting Turning

86. The Handle of this box will be turned on a lathe. What length of a piece of wood is required? Handle Click on the correct answer from the choices below

87. What is the correct name for the process shown below Brazing Forging Welding Casting Turning

88. What is the correct name for the process shown below Brazing Forging Welding Casting Knurling

89. What is the correct name for the drill bit shown on the left Twist Drill Forstner bit Flat Bit Masonry Bit Centre drill

90. What is the correct name for the machine shown on the left Arc Welder Spot Welder Mig Welder Tig Welder

91. On the diagram to The left where is the pilot hole

92. Which of the following hardwoods is most suited for the manufacture of a garden bench? Rosewood Teak Mahogany Birch Balsa

93. Which of the following hardwoods is most suited for the manufacture of chopping board? Rosewood Beech Oak Elm Balsa

94. What is the correct name for the material shown on the left? Pine Blockboard MDF Hardboard Chipboard Veneered Chipboard Mahogany Plywood

95. What is the correct name for the material shown on the left? Pine Blockboard MDF Hardboard Chipboard Veneered Chipboard Mahogany Plywood

96. What is the correct name for the material shown on the left? Pine Blockboard MDF Hardboard Chipboard Veneered Chipboard Mahogany Plywood

97) On the diagram above indicate the Runner

98. What is the correct name for the material shown on the left? Pine Blockboard MDF Hardboard Chipboard Veneered Chipboard Mahogany Plywood

It takes time to adjust the spanner to the correct size. The adjustable Spanner has a tendency to round the corners of the nut or bolt. 99. What is the main disadvantage to using an adjustable spanner Adjustable spanners are bigger than ordinary spanners.

100. Where is the tailstock ?

Well Done Quiz Completed

Wrong Click here to try again