Brandywine Communications 2018 Sales Meeting Cody WY May 15/16 2018 Introducing the M212 Brandywine Communications 2018 Sales Meeting Cody WY May 15/16 2018

What is the M212? The M212 is a new modular master clock system It is intended as the replacement for the M210 and M211 series It is derived from the Modular Master Clock system It is still not ready for sale but will be announced in the next 30 days

Why build another Modular System? The MMC is a high end product and costly to produce The M212 is essentially a cost reduced version for commercial markets Feature set is designed to compete with SecureSync S650 at lower cost Some features may make their way back into the MMC

Key features 1U chassis LCD display and keypad for IP address setup and basic status Single Master Clock Module 6 output slots Single Power Supply

View1

View 2

View 3 Front View Rear View

Key “Non-features” We do not want to cannibalize MMC sales, so certain features will never be available on the M212 No redundancy No dual power No dual MCM No Hot Swap Spoofing detection High Performance Rubidium

User Interface 40x 2 front panel LCD with 5 way keypad Basic status IP address setup (needed to talk via web page) Secure Web Browser https// is new baseline requirement for most government systems Simple Network Management Protocol SNMP v1,2c, 3

Synchronizing Inputs Multi – GNSS receiver SAASM/M-Code GPS* IRIG B GPS, GLONASS, Beidou & Galileo ready US Government users can use GPS only Other constellations always include GPS SAASM/M-Code GPS* IRIG B Have Quick/1PPS RS232/422 (via OSM) Optical link from another M212 ( via OSM) * * Planned

Available Oscillators Baseline Oscillator Temperature Compensated Crystal Oscillator (TCXO) – Holdover is ~1ms/day depending on temperature Optional Oscillators Oven Controlled Crystal Oscillator (OCXO) Holdover is ~25µs/day depending on temperature Rubidium Oscillator (Rb) Holdover is ~10µs/day depending on temperature

Output Modules Output Module types “Intelligent” “Distribution” Similar to MMC, configurable and with individual output alarms “Distribution” Signal is generated on MCM and the OSM provides multiple buffered outputs No output alarms

Universal O/P 4 outputs Outputs are programmed per connector from the list of outputs BNC or 3 pin connector may be used IRIG Codes Other timing signals IRIG A (2 variants) Have Quick IRIG B (9 variants) BCD (2 variants) IRIG G (2 variants) XR3 IRIG H (1 variant) 2137 1PPS 1PPM

NTP Module Carryover from MMC 2 port 100BaseT Supports NTP V3, V4 Supports encryption and authentication

Octal Serial Port “Distribution Module” 8 serial ports All ports have the same message generated on MCM Ports can be link set for RS232 or RS422/485 One port can be configured as a sync input to the M212

Distribution Modules Planned 5 MHz 10 MHz 1PPS IRIG B Have Quick/IRIG B DCLS

Intelligent Modules Planned(1) PTP Grand Master /Slave 4 port Module 10 GbE - 1 ea. 1 GbE -3 ea. 1 port will be configurable as a reference input Status: Basic hardware engine to power this is due in next 30 days Customer hardware available this year

Intelligent Modules Planned(2) E1/T1 Module Basic development has been done for HPTS 12 outputs nX8kHz Module

Pricing and competition Final Pricing has not been set – the numbers below are budgetary M212 1U MMC Spectracom Secure Sync Base Unit (Chassis, PSU, TCXO MCM,GPS, antenna) 3390 8945 3400 Add OCXO 500 std IRIG B in/out 750 1PPS in/out 495 3 GbE ports 1400 planned 1500 Universal card 1095 1135 Not available