Tin Ceiling Installation Brian Greers Tin Ceilings Brian Greers Tin Ceilings www.tinceiling.com.

Slides:



Advertisements
Similar presentations
Unit 55 Roof Finish Roof Overhangs and Cornices • Open Cornices • Closed Cornices • Cornice Soffit Systems • Covering Roofs • Asphalt Shingles • Wood Shingles.
Advertisements

Interior Wall and Ceiling Finish
The Making of a Quarter Map. Making of the Pop's Shop Quarter Map 2 Cutting and Staining the Map The first step in making a Quarter map is cutting out.
Introduction To Trim Copyright © Texas Education Agency, All rights reserved.
Measuring and Layout Tools
CON 4003 Construction Estimating Prof R. V. Locurcio.
Optimum Round Pool Instructions. Prepare the pool site Remove all the grass on a surface 2’ wider than the size of the pool Level the ground.
Flexible Manufacturing Common Sheet Metal Seams Copyright © Texas Education Agency, All rights reserved.
Welcome to Hardie 101 Basic Training
ICRA Panel System Installation Instructions
Building a Wooden Planter Box. The Most Important Part of any Project is the Planning Determine what type of wood to use for the box (pine, cedar, cypress,
Unit 42 Floor Framing Floor Unit Resting on Sill Plates • Floor Unit Resting on Cripple Walls • Posts and Beams • Floor Joists • Subfloor • Floor Underlayment.
Residential Framing Prints Unit 14.
The Little Nikki Assembly Instruction By Laser Dollhouse Designs.
Unit 61 Interior Trim Wood Molding • Composite Molding • Trimming Door Openings • Trimming Window Openings • Installing Base Molding • Installing Ceiling.
Ledgewood Farm greenhouse construction How do I Start? to I’m Finished!
All About Flats By Samantha Lee. What is a flat? Theatre flats are large pieces of constructed and painted wood that are placed on the stage to serve.
SEACORK INSTALLATION ON A CATAMARAN The first step is to make templates of all corner pieces to be cut from sheet material, which will be used for border.
INSTALLATION INSTRUCTIONS FOR GERARD METAL SHINGLES
Firestone Building Products EPDM Training. Membrane Attachment.
WOOD MATERIALS TECHNOLOGY 4 th Edition. Chapter 29 Finishes.
Design and Technology Marking and Measuring Tools.
House Construction. Learning Standard 5. Construction Technologies Construction technology involves building structures in order to contain, shelter,
Furniture CONSTRUCTION
Drafting Rear Elevations. Start with outer frame when drafting standard flat. Heights are generally in multiples of 2’-0”. Outer Frame.
Wall and Ceiling Construction Vocabulary
CONSTRUCTING A FIVE CABIN LATRINE
Lesson Siding Agricultural Structures Interest Approach What types of buildings siding have you seen on the farm? What are some of their advantages?
B2 Lines can create the illusion of surface textures C2 Artworks can be formal, analytical descriptions of objects E2 Positive and negative space are.
Constructing Homes and Other Buildings
SHED CONSTRUCTION A Visual Guide. C.A.D. Example.
Choosing the Right Siding When selecting siding, there are six basic issues to consider: 1. Water Resistance. Water-resistant types of siding will have.
Preparing Surfaces and Selecting Paints Preparation Prior to Painting  Start by gathering together all the tools and equipment you will need.
Construction Carpenter Vocabulary Created by The University of North Texas in partnership with the Texas Education Agency.
Fiberglass Chassis Cover 101 Why custom shape lightweight strong Why not time consuming Brought to you by: detail oriented can be costly.
Dry lining by direct bond – overview
Wall and Ceiling Construction
Chapter 23 Plumbing Systems. Objectives After reading the chapter and reviewing the materials presented the students will be able to: Identify several.
1. b. Rip Saw 2. d. Used for cutting with the grain.
Finishing the Building
INTD 54 other components. moldings cover, enhance and decorate a plain surface standing trim: fixed length—doors & windows.
Drywall Theory. Dry Wall Saw Dry wall T-Saw Dry Wall Lift.
Wall Treatments. What to consider? Walls are the largest background space Wall condition Cost Room function Desired look lifestyle.
Choose a category. You will be given the answer. You must give the correct question. Click to begin.
Using commercial patterns Trimming, pinning, cutting out, transferring pattern markings. © PDST Home Economics.
Principles of Manufacturing Copyright © Texas Education Agency, All rights reserved 1.
Creating a Sun Catcher. Choose a Pattern For this project, you will need to choose a pattern from my Sun Catcher collection for Glass Eye. You will find.
How to Build a Divider Wall By Charysse Roberson.
Finishing your clay project. Set-up  Get your piece from the kiln room  Examine it  Does it have any rough areas or small bumps?  Get some sand paper.
Sheet Metal: Notes and Descriptions MachinesProceduresTools.
Objective Use agricultural mechanics hand tools properly.
Interior Paneling Installation Copyright © Texas Education Agency, All rights reserved.
Required materials for glassing foam. 220, 400 & 600 Grit sandpaper Minwax Polycrylic (clear satin) 3/4oz glass cloth Foam brush Xacto knife (sharp blade)
Everything about drywall (lather)
Residential Construction 2201 Installing Vinyl Siding.
Monolith Collection and Preparation For soils without restrictive layers Conrad Neitsch USDA-NRCS MLRA Region 9 Staff Temple, TX.
Drafting 2 (Arch) Quiz Review #5
The problem is to design, construct and test the most efficient bridge within the specifications. Back to start of slide show.
Potting Bench Plans Matt Howell Brooks County High School ___, Georgia Georgia Agricultural Education Curriculum Office, August, 2004.
Lighten Up! Single Window Kits Add Light and Appeal To Home Bathrooms.
Potting Bench Plans Matt Howell Brooks County High School Quitman, Georgia Quitman, Georgia Georgia Agricultural Education Curriculum Office, August, 2004.
VIEW SERIES with Sliding Door
Flexible Manufacturing
How to Build a House.
Assembly instructions for M-K all bolt together hoppercone kit.
Components of Construction
Wood Frame Construction
INTD 503- Materials Topic: Wall Coverings
Make a Two Note Wooden Whistle 1: Cut a piece of wood 20mm thick x 30mm wide to a length of 100mm. Use a back saw and a miter box to make the cut. 2: Use.
Presentation transcript:

Tin Ceiling Installation Brian Greers Tin Ceilings Brian Greers Tin Ceilings

Brians Basement Ceiling Installation. Measure the room so you can plan the ceiling design on a piece of paper. Brian Greers Tin Ceilings Brian Greers Tin Ceilings

A plan, drawn to scale, of the ceiling showing the layout of the Panels, Moldings, Fillers and Cornices that are going to be used. Brian Greers Tin Ceilings Brian Greers Tin Ceilings

Cover the ceiling with wood (mahogany or plywood), making sure the work area is level, flat and smooth. Brian Greers Tin Ceilings Brian Greers Tin Ceilings

Cover all ducts with plywood frames and sheets to create an enclosure. Brian Greers Tin Ceilings Brian Greers Tin Ceilings

Transfer the layout plan to the ceiling by making a gridwork with a chalk line. Brian Greers Tin Ceilings Brian Greers Tin Ceilings

Panels begin at the farthest wall from the main entrance of the room and work in rows back towards the main entry. Brian Greers Tin Ceilings Brian Greers Tin Ceilings

Begin installing by overlapping the Panels, Moldings, Fillers and Cornices making sure these items lap away from the prevailing light and main entrance. Brian Greers Tin Ceilings Brian Greers Tin Ceilings

Nail approximately every 6 around the outside edges of the tin panel. Brian Greers Tin Ceilings Brian Greers Tin Ceilings

Fill the area between the Panels and the walls with Filler pieces. Brian Greers Tin Ceilings Brian Greers Tin Ceilings

Install the Moldings in the space between the Panels and the Fillers. Brian Greers Tin Ceilings Brian Greers Tin Ceilings

Miter the corners of the Moldings to make a nice fit. Brian Greers Tin Ceilings Brian Greers Tin Ceilings

When adding the Cornices, start by nailing a piece of wood up to the wall for the base of the Cornice to rest on. Brian Greers Tin Ceilings Brian Greers Tin Ceilings

Create wood braces in the same shape. Nail the braces to the wall so that the middle and both ends of the Cornice can be nailed to them for extra support. Brian Greers Tin Ceilings Brian Greers Tin Ceilings

Miter all outside corners. First add the wooden bases. Brian Greers Tin Ceilings Brian Greers Tin Ceilings

Miter each end of the Cornices by cutting each piece on an angle. Check the fit before installing. Brian Greers Tin Ceilings Brian Greers Tin Ceilings

Cope all inside corners. First add the wooden bases. Brian Greers Tin Ceilings Brian Greers Tin Ceilings

Fit one of the Cornices so it is flat to the wall. Brian Greers Tin Ceilings Brian Greers Tin Ceilings

Cope the second Cornices end by cutting the piece on an angle. Check the fit before installing. Brian Greers Tin Ceilings Brian Greers Tin Ceilings

Tap any loose seams together with a small piece of wood. Brian Greers Tin Ceilings Brian Greers Tin Ceilings

Caulk the Panel, Molding, Filler and Cornice seams to create a smooth and tight fit. Brian Greers Tin Ceilings Brian Greers Tin Ceilings

For painted Panels – use painters caulking. Brian Greers Tin Ceilings Brian Greers Tin Ceilings

For plated and bright Panels – use a clear caulking at your discretion. In some situations it is not needed. Brian Greers Tin Ceilings Brian Greers Tin Ceilings

Completed tin ceiling – not painted or finished. Brian Greers Tin Ceilings Brian Greers Tin Ceilings

If ceiling is left in tin finish, coat with a clear lacquer or polyurethane (it is always best to do a test spot before starting). Brian Greers Tin Ceilings Brian Greers Tin Ceilings

For painted ceilings, use a bonding primer that will adhere to metal. Finish with oil or latex paint (oil is preferred). Brian Greers Tin Ceilings Brian Greers Tin Ceilings

The Painted Ceiling Brian Greers Tin Ceilings Brian Greers Tin Ceilings

The Painted Ceiling Brian Greers Tin Ceilings Brian Greers Tin Ceilings

The Painted Ceiling Brian Greers Tin Ceilings Brian Greers Tin Ceilings

To add some texture and give the ceiling an antique look, sand the raised ridges of the design with sandpaper. Brian Greers Tin Ceilings Brian Greers Tin Ceilings

Sanding the raised ridges over the entire ceiling will give a more unified look. The designs in the Panels will be more noticeable and distinct. Brian Greers Tin Ceilings Brian Greers Tin Ceilings

The Painted and Finished Ceiling Brian Greers Tin Ceilings Brian Greers Tin Ceilings

The finished room with its new tin ceiling. Brian Greers Tin Ceilings Brian Greers Tin Ceilings

Phone: (519) Fax: (519) Phone: (519) Fax: (519)