Traditional Fixtures & Fittings

Slides:

Advertisements

Similar presentations

Knock Down Fittings Product Design.

Advertisements

TIMBER JOINERY.

เทคโนโลยีการสร้างอุปกรณ์จับยึด

Kwikset Rekey Ultramax Rekeying the Ultramax by Kwikset this presentation is designed for beginners.

Fasteners, Adhesives and Clamping Most wood products must be fastened together. There are several methods to accomplish this. Different types of glues,

Hinges. Hinges Hinges generally consist of two leaves & a knuckle. Hinges generally consist of two leaves & a knuckle. The knuckle is formed by interlocking.

Mortise Locks Created by M.Martin 9/05. Types - your Ref: P45 of textbook.

Initial Design The initial Design was a horizontal dispense - horizontal load system where the smart cartridge was loaded from a maintenance hatch on the.

860 21/2”-10”. Modification Overview  Production of the 2½” – 10 sizes began in  Lead free version (LF860) was introduced in Parts do not.

Making a trap cage. You need plastic bottles, wire, string, a plastic bag and tools.

Electrical plant. Traditional wall (Red hollow brick) Plasterboard wall Rapid installation flush mounting solution FINAL EFFECT Traditional wall (Red.

Specification section 3.3

TOUGHENED GLASS FIBER REINFORCED BODY TOUGHENED GLASS FIBER REINFORCED BODY ONE PIECE BODY FOR OPTIMUM INTEGRITY ONE PIECE BODY FOR OPTIMUM INTEGRITY STANDARD.

Old Main Group. Design Issues There are no changes to the overall Design It will remain the way it is The Attachment Issue is resolved Going to screw.

DO NOW LESSON # 1)What are the 5/20/2015. Focus Point: What are the Types of Punches? ► Instructional Objectives: ► 1. List the purpose of various punches.

Fasteners Assignment Part C: 3/8-16 UNC-2A 1.5 FLAT HEAD.

 What is joinery? In our case – we will be looking at the fastening or combining of two or more boards together when building our projects.  It is important.

BTM I Ar. Mahua Biswas1 CARPENTRY TOOLS  Classification of Carpentry Tools 1)Marking and setting out 2)Cutting 3)Boring 4)Planing tools 5)Hammers and.

Residential Construction Residential Doors *Source: (1) Carpentry & Building Construction Feirer & Freirer.

Flexible Manufacturing 1 Copyright © Texas Education Agency, All rights reserved. Machining Skills.

Mounting best practices 1.Always mount to a solid, rigid surface when available 2.Whenever possible, it is recommended you mount the ShockLog directly.

Traditional Furniture Handles & Stays 1 J.Byrne 2014.

Traditional Fixtures & Fittings 1 J. Byrne Fixtures & Fittings J. Byrne

J.Byrne Block Joint : Hard plastic Surface fitting, side to end Modesty Block : Hard plastic. Surface fitting, side to end Bolt & Cam : Metal.

PAVSYS PAVSYS ™ PAVSYS PAVSYS MODULAR ENGINEERED SUSTAINABLE HABITATS.

© 2011 Pearson Education, Inc. All Rights Reserved Automotive Technology, Fifth Edition James Halderman FASTENERS AND THREAD REPAIR 8.

TIMBER (WOOD) Types, Properties, Joints and Finishes.

ID 1.75 Material list: aluminum ¼ X ¾ X 6 in flat bar ¾ X 6 in round stock 1 X 6 in round stock 2 ea 5/16 heli-coil Weld 1” joints.

Fasteners and Thread Repair

Knock Down Fittings J.Byrne 2014.

Traditional Furniture Locks 1 J. Byrne Locks Small finely made locks are fitted to furniture and boxes. However, they do not provide total security,

Counter Bore. Spot Facing – Provides a true bearing surface for a washer. Counter boring – Provides a recess for a bolt head, bushing or pin.

Timber Products and Furniture Technologies (HSC) Hardware and Fittings.

Traditional Fixtures & Fittings 1 J. Byrne Fixtures & Fittings J. Byrne

Installing a single Dreamscreen Set unit in place and attach with 2 ½ “ screw. Do not tighten the screw yet, tighten just enough to keep from falling.

Fasteners and Thread Repair 08 Introduction to Automotive Service James Halderman Darrell Deeter © 2013 Pearson Higher Education, Inc. Pearson Prentice.

………..Continued - Parts of Radial Drilling Machine -Functions

1 Jim Thomas - LBL Sector Tools – a conversation with Jon Wirth and Eric Anderssen August 28 th, 2015.

Traditional Furniture Hinges

Installing Hinges Created By M.Martin 9/05. Mark the hinge position on the door edge 150mm from the top of the door and 225mm from the bottom of the door.

STEP 1: ASSEMBLE INSERT PLATES 1.Assemble insert plates by press fitting roller bearing and adapter plate into assembly 1.1 Prep all mating surfaces to.

Completed Front and Rear Standard 10 ½” 1 ½” 3 ¼” 4 ½” 1” ¾” 1 ½” 6” ¾” Channel Length: 5 ¼”, ¾” from end.

Machining Skills Flexible Manufacturing.

STEP 1: ASSEMBLE ANGLE PLATES

DRILLING Dept. of Mech & Mfg. Engg..

FASTENERS AND THREAD REPAIR

INSTALLING BYRNE POWER BOX INTO FLEX SYSTEM

Construction and Assembly

Objectives Describe the fasteners, anchors, and adhesives used in construction and explain their uses. a. Identify various types of nails and cite uses.

Easycliner (Motorized Version) Assembly Instruction

Traditional Furniture Locks

THE WOOD AND IT’S DERIVATIVES

STEP 1: ASSEMBLE ANGLE PLATES

MACHINE PARTS (FOR DCE / DIT)

Knock Down Fittings J.Byrne 2015.

Year 11 Occupational Studies – Carpentry and Joinery

Building Construction I Sofia Sebastian 1

Building Construction I Sofia Sebastian 1

PRODUCT ARGUMENTATION

Mechanical hardware.

Rail fixtures & fastening

880V 21/2”-10”.

MACHINE DRAWING NAME : SYED AMER UR RAHMAN B.TECH 2 – 2

Traditional Furniture Handles & Stays

Hinges & Locks.

Civil engineering materials windows & Doors

Traditional Furniture Hinges

Presentation transcript:

Traditional Fixtures & Fittings Locks J. Byrne 2013 Traditional Fixtures & Fittings

J. Byrne 2013 Fixtures & Fittings

J. Byrne 2013 Escutcheons An escutcheon An escutcheon is a small decorative metal plate used to surround a keyhole cut in timber. Most escutcheons are pinned to the surface, but there are also small unobtrusive recessed versions.

Ball Catch This catch comprises a spring loaded steel ball trapped in a cylindrical brass case that is inserted in the edge of a cupboard door. When the door is closed the ball springs into a recess in a metal striker plate screwed to the carcase. J. Byrne 2013

Door Bolt On a twin door cupboard, one door is often fitted with a pair of neat surface mounted or flush bolts and the other with a lock or catch. J. Byrne 2013

Magnetic Catch Small-encased magnets are screwed to the inside of a carcase side panel or located in a hole drilled in its edge. The magnet attracts a flat metal striker plate fixed to the cupboard door. J. Byrne 2013