Ideal Otto Cycles for I.C. Engines

Slides:

Advertisements

Similar presentations

Department of Mechanical Engineering ME 322 – Mechanical Engineering Thermodynamics Lecture 28 Internal Combustion Engine Models The Otto Cycle The Diesel.

Advertisements

İsmail ALTIN, PhD Assistant Professor Karadeniz Technical University Faculty of Marine Sciences Department of Naval Architecture and Marine Engineering.

Internal Combustion Engine Theory

EGR 334 Thermodynamics Chapter 9: Sections 1-2

Lab IV: Internal Combustion Engine 14:650:431:03 Max Tenorio.

Internal Combustion Engines. Ideal Diesel Cycle Ideal Diesel Cycle.

Measuring Engine Performance ME 115 Laboratory Spring 2008.

Experiment #4 IC Engine.

Fuel-Air Modeling of IC Engine Cycles P M V Subbarao Professor Mechanical Engineering Department Another Step towards Phenomenological Modeling.….

Shaft Power Generation Devices - 1

Physics 52 - Heat and Optics Dr. Joseph F. Becker Physics Department San Jose State University © 2003 J. F. Becker.

Quiz Twelve Solutions and Review for Final Examination

Thermodynamics Professor Lee Carkner Lecture 18

Thermo & Stat Mech - Spring 2006 Class 5 1 Thermodynamics and Statistical Mechanics Heat Engines and Refrigerators.

Thermodynamic Analysis of Internal Combustion Engines P M V SUBBARAO Professor Mechanical Engineering Department IIT Delhi Work on A Blue Print Before.

Shaft Power Cycles Ideal cycles Assumptions:

For next time: Read: § 8-6 to 8-7 HW11 due Wednesday, November 12, 2003 Outline: Isentropic efficiency Air standard cycle Otto cycle Important points:

Gas Power Cycle - Internal Combustion Engine

Power Generation Cycles Vapor Power Generation The Rankine Cycle

INTERNAL COMBUSTION ENGINES (reciprocating). Geometry.

Thermodynamic Cycles Air-standard analysis is a simplification of the real cycle that includes the following assumptions: 1) Working fluid consists of.

ENGR 2213 Thermodynamics F. C. Lai School of Aerospace and Mechanical Engineering University of Oklahoma.

Work Distribution Analysis of I.C. Engine Cycles P M V Subbarao Professor Mechanical Engineering Department Find true Scope for Development….

Thermodynamic Cycles for CI engines In early CI engines the fuel was injected when the piston reached TC and thus combustion lasted well into the expansion.

Analysis of Thrust Equation for Ideal Turbo Jet Engine P M V Subbarao Professor Mechanical Engineering Department Understanding the Features of A True.

ENTC-370PROF. ALVARADO1 THERMODYNAMICS LAB: EES- Refrigeration Cycle & Internal Combustion Engine ENTC

HEAT ENGINE D.A.DEGREE ENGG. & TECHNOLOGY

Power and Refrigeration Cycles – Applications (YAC: Ch. 7) Most devices operate on cycles (open or closed) of two common types: Power Cycles: Produce net.

Stochiometry of Real Combustion P M V Subbarao Professor Mechanical Engineering Department A First Step to Understand &Control Rate of Heat Release ….

Thermodynamic Cycles for CI engines

ME 200 L35 Ground Transportation (Air Standard Otto Cycle) 9.1 and 9.2 Material not picked up this week may be recycled! ME 200 L35 Ground Transportation.

TEKNIK PERMESINAN KAPAL II (Minggu – 3) LS 1329 ( 3 SKS) Jurusan Teknik Sistem Perkapalan ITS Surabaya.

Gas Power Cycles Thermodynamics Professor Lee Carkner Lecture 17.

Fuel-Air Modeling of Combustion in I.C. Engines P M V Subbarao Professor Mechanical Engineering Department Another Step towards Phenomenological Modeling.….

MT 313 IC ENGINES LECTURE NO: 04 (24 Feb, 2014) Khurram Yahoo Group Address: ICE14.

Design & Selection of Systems for Best Heat Release P M V Subbarao Professor Mechanical Engineering Department Supply of Sufficient Oxygen for Digestion.

Inovace bakalářského studijního oboru Aplikovaná chemie Reg. č.: CZ.1.07/2.2.00/

AR Thermodynamics I Fall 2004 Course # 59:009 Chapter 9, Section 2 Professor Ratner.

EXAMPLE PROBLEMS FOR MIDTERM I.

Engine Cycle Analysis. Air Standard Otto Cycle.

Diesel Cycle and the Brayton Cycle Chapter 9b. Rudolph Diesel  German inventor who is famous for the development of the diesel engine  The diesel engine.

MT 313 IC ENGINES LECTURE NO: 03 (19 Feb, 2014) Khurram Yahoo Group Address: ICE14.

Difference Between otto and diesel cycle

Analysis of Diesel Cycle and Scope for Modification P M V Subbarao Professor Mechanical Engineering Department Creation of Rational Models for Engines…

THERMODYNAMIC ANALYSIS OF IC ENGINE Prepared by- Sudeesh kumar patel.

A. Diesel cycle : The ideal cycle for CI engines

SNS COLLEGE OF ENGINEERING THERMAL ENGINEERING

Chapter: 08 POWER CYCLES.

Strategies for Complete Expansion in I.C. Engine

Ideal but Practicable Cycles for I.C. Engines

Real I. C. Engines Vs Ideal Models

Gas Power Cycle - Internal Combustion Engine

Fuel-Air Modeling of IC Engine Cycles - 1

Engineering Thermodynamics ME-103

SI Engine Cycle Actual Cycle Intake Stroke Compression Power Exhaust

Thermo-Economic Analysis of Otto Cycle

Lecture 43 Heat engine and efficiency

Ideal Diesel and Dual Cycles for I.C. Engines

Measuring Engine Performance

Thermodynamic Analysis of Ramjet Engines

Real Rankine Cycle with Superheat

Creation of Cycles for Mobile Power Plants

Ideal Diesel and Dual Cycles for I.C. Engines

i.C engines Prepared By: Dr.S.MAGBUL HUSSAIN PROFESSOR AND HOD

20th Century Thermodynamic Modeling of Automotive Prime Mover Cycles

Jet Aircraft Propulsion

Ideal Otto Cycles for I.C. Engines

19th & Early 20th Century SI Models for Automotive Prime Mover

Thermodynamic Analysis of Internal Combustion Engines

WUP#21 Which is an empirical formula (E.F.) and which is a molecular formula(M.F.)? 1. H2O 2. C4H10 3. CO2 4. CH2O 5. C6H12O6.

Presentation transcript:

Ideal Otto Cycles for I.C. Engines

Fuel calorific value (kJ/kg) Ford ECOSPORT Details 1.5P Ambiente Displacement (cc) 1499 Max Power output(kW) 82@6300RPM Max. Torque (Nm) 140@4400RPM Compression Ratio 11:1 Fuel calorific value (kJ/kg) 48,000

Ideal Otto

Analysis of Otto Cycle

Engine Specifications due to an Ideal Otto Cycle

Effect of Compression Ratio :Thermodynamic Performance Parameters

Effect of Compression Ratio : Thermo-chemical Performance Parameters

Other components of Petrol Name of Hydro-carbon Sample 1 Sample 2 Formula Ethanol 13.40% 12.10% C2H6O 2-methyl-pentane 10.20% 4.50% C6H14 Hexane 0% 2.10% Pentane 5.50% 3.70% C5H12

Isentropic Compression model with variable properties For compression from 1 to 2:

First Order Models for Variable Specific Heats

Isentropic expansion model with variable properties For expansion from 3 to 4: