ME321 Kinematics and Dynamics of Machines

Slides:



Advertisements
Similar presentations
Mechanics of Machines Dr. Mohammad Kilani
Advertisements

1 Cams Cams are used to convert rotary motion to oscillatory motion (almost always) or oscillatory motion to rotary motion (rarely) For high speed applications.
Tutorial schedule changes  Original schedule: cam follower displacement diagram --March 13,2014 cam profiles --March 20,2014 Ordinary gear trains --March.
Mechanical Engineering Dept.
§9 - 2 Follower Motion Curves §9 - 3 Graphical Cam Profile Synthesis §9 - 4 Cam Size and Physical Characteristics §9 - 1 Applications and Classification.
ME451 Kinematics and Dynamics of Machine Systems Relative Kinematic Constraints, Composite Joints – 3.3 October 4, 2011 © Dan Negrut, 2011 ME451, UW-Madison.
CAM.
Mechanism Design Graphical Method
Mechanics of Machines Dr. Mohammad Kilani
Cams Cam Basics.
Cams are used to convert rotary motion into reciprocating motion
Dynamic Mechanisms. CAMS A cam is a machine part for transferring rotary motion to linear motion In a radial plate cam, the cam is mounted on a rotating.
Presented By: Wahaj Adil TS-1
§1 - 1 Study Object and Content §1 - 1 Study Object and Content §1 - 2 Purpose §1 - 2 Purpose Chapter 1 Introduction.
Unit I BASICS OF MECHANISMS
Theory of Machines Lecture 4 Position Analysis.
Kinematics geometry extensions for delta robots - RSLogix 5000 V16.03
Fundamentals of Descriptive Geometry (Text Chapter 26)
Mechanism Design Graphical Method
CAD TECHNOLOGY COMPUTER AIDED DESIGN.
ME1204 – MECHANICS OF MACHINES
DESCRIBING MOTION: Kinematics in One Dimension CHAPTER 2.
Kinematics of Particles Lecture II. Subjects Covered in Kinematics of Particles Rectilinear motion Curvilinear motion Rectangular coords n-t coords Polar.
ME451 Kinematics and Dynamics of Machine Systems Relative Kinematic Constraints, Composite Joints – 3.3 October 6, 2011 © Dan Negrut, 2011 ME451, UW-Madison.
THOERY OF MECHANISMS AND MACHINES Module-05 Velocity & Acceleration Analysis Instructed by: Dr. Anupam Saxena Associate Professor Department of Mechanical.
The Big 3 Equations of Motion We have three equations that can be used to solve most Problems, when dealing with translational (tangential) motion. These.
CAM. Meghe Group of Institutions Department for Technology Enhanced Learning 2.
Y.A. Khulief 1 MECHANICS OF MACHINES Reciprocating radial roller follower Oscillating roller follower.
PHY 093 – Lecture 1b Scalars & Vectors Scalars & vectors  Scalars – quantities with only magnitudes Eg. Mass, time, temperature Eg. Mass, time,
Fundamentals of Descriptive Geometry AT 301 Dr. Trent.
CAM PROFILE -Converts linear motion into rotary motion ` TERMS -GRAPH OF DISPLACEMENT -SCALE -CAM SHAFT/SPINDLE -FOLLOWER -DIRECTION -MINIMUM CAM PROFILE.
PREPARED BY: PATEL MANTHAN(12ME132)
Unit III KINEMATICS OF CAMS
CAM MACHINE ELEMENT Prepared by R.A.ARUL RAJA, ASSISTANT PROFESSOR,
THOERY OF MECHANISMS AND MACHINES
CAMS AND FOLLOWERS SUBMITTED BY:- Guided By:
THOERY OF MECHANISMS AND MACHINES Module-10 CAMS (DESIGN) Instructed by: Dr. Anupam Saxena Associate Professor Department of Mechanical Engineering Indian.
STRAIGHT LINE MECHANISM GROUP MEMBERS DESAI SHIVAM DEVENDRAKUMAR DEVANI AJAY NAIK DHWANIT DIKESH Ken.
Higher Order Joints Motion Generation Mechanisms Rotating a monitor into a storage position Moving a storage bin from an accessible position to a stored.
Cams and Cam Followers.
What is the Cam? A Cam is a rotating or sliding piece in a mechanical linkage used especially in transforming rotary motion into linear motion. A cam may be defined as a rotating machine part designed to.
Cams are used to convert rotary motion into reciprocating motion
Cams and Followers Eccentric Cam Pear Cam Drop Cam
CAMS WITH SPECIFIED CONTOURS
Synthesis Of Mechanism
Pimpri Chinchwad Polytechnic, Nigdi.
Chapter 05 CAMS & FOLLOWER
Cams Cams are used to convert rotary motion to oscillatory motion (almost always) or oscillatory motion to rotary motion (rarely) For high speed applications.
CAM & FOLLOWER Prepared by B.BALAMURALI AP/MECH
ME321 Kinematics and Dynamics of Machines
ME321 Kinematics and Dynamics of Machines
CAM Design – Part 2, Focus on the CAM
X-Camme 2010 ML A easy software for a complex object.
ME321 Kinematics and Dynamics of Machines
ME321 Kinematics and Dynamics of Machines
ME321 Kinematics and Dynamics of Machines
ME321 Kinematics and Dynamics of Machines
ME321 – Kinematics and Dynamics of Machines Introduction (Continued)
WEEK 5 Dynamics of Machinery
ME321 Kinematics and Dynamics of Machines
ME321 Kinematics and Dynamics of Machines
Steve Lambert Mechanical Engineering, U of Waterloo
Cams Prepared by: Mr. Navneet Gupta
ME321 Kinematics and Dynamics of Machines
ME321 Kinematics and Dynamics of Machines
ME321 - Kinematics and Dynamics of Machines Design Process Notes
Simple case: a diatomic with masses m1 and m2
ME321 Kinematics and Dynamics of Machines
Coordinate Systems Cartesian, Relative and Polar
Presentation transcript:

ME321 Kinematics and Dynamics of Machines Steve Lambert Mechanical Engineering, U of Waterloo 2/23/2019

Cam Design - Cam Profiles 2/23/2019

Cam Profile Design Once the follower displacement is specified, we can choose a follower type and design the actual cam We can design the cam either graphically, or analytically Both procedures are fundamentally the same 2/23/2019

Graphical Cam Profile Design Flat-Faced Follower 2/23/2019

Graphical Cam Profile Design Roller Follower 2/23/2019

Graphical Cam Profile Design Offset Roller Follower 2/23/2019

Analytical Cam Profile Synthesis 2/23/2019

Analytical Cam Profile Design Translating flat-faced follower (Follower half-width) Polar coordinates of contact point Cartesian coordinates of contact point 2/23/2019