Reinforced Concrete Design-7 Design of Continuous beams and Slabs

Slides:

Advertisements

Similar presentations

1. By Dr. Attaullah Shah Swedish College of Engineering and Technology Wah Cantt. CE-407 Lec-02 Structural Engineering.

Advertisements

1.

Outline CH1.Introduction CH2.Preliminary Design CH3.3D Model.

Reinforcement for Plates Course CT4150 Lecture12 5 Jan

Graduation Project Thesis: Structural Analysis & Design of “Al-Mansour Mall”

An-Najah National University

Design of Concrete Structure I

Reinforced Concrete Design-8

CEE Capstone II Structural Engineering

Lecture 33 - Design of Two-Way Floor Slab System

Rigid-Frame Structures

Shear Wall Structures CE Design of Multi-Story Structures

Lecture 15- Bar Development

1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore Mob:

Lecture Goals Slab design reinforcement.

Stair Design. Stair Types Straight stairs.

Torsion in Girders A2 A3 M u = w u l n 2 /24 M u = w u l n 2 /10M u = w u l n 2 /11 B2 B3 The beams framing into girder A2-A3 transfer a moment of w u.

Lecture Goals Doubly Reinforced beams T Beams and L Beams.

Finding a Quadratic Equation from Complex Roots. Write an equation from the Roots Find the equation of a quadratic function that has the following numbers.

1. By Dr. Attaullah Shah Swedish College of Engineering and Technology Wah Cantt. Reinforced Concrete Design-II Lec-3 Retaining walls.

Code Comparison between

1. By Dr. Attaullah Shah Swedish College of Engineering and Technology Wah Cantt. CE-401 Reinforced Concrete Design-II.

Reinforced Concrete Design-II

1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore Mob:

1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore Mob:

Plain & Reinforced Concrete-1 CE-313

BEAMS AND COLUMNS.

By Dr. Attaullah Shah Swedish College of Engineering and Technology Wah Cantt. Reinforced Concrete Design-4 Design of doubly reinforced beams.

GARY NEWMAN STRUCTURES OPTION ADVISOR: DR. HANAGAN SENIOR THESIS PRESENTATION SPRING 2008.

AN-Najah National University Faculty of Engineering Civil Engineering Department Structural Design of a Hotel Building Prepared by: Mohammed Qawariq Faris.

1. By Dr. Attaullah Shah Swedish College of Engineering and Technology Wah Cantt. CE-401 Reinforced Concrete Design-II Design of Stair cases.

Justin Purcell Structural Option Advisor: Dr. Hanagan.

Isolated footing with axial load and moment

By Dr. Attaullah Shah Swedish College of Engineering and Technology Wah Cantt. Reinforced Concrete Design-3 Flexural Design of Beams.

Continuously Reinforced Concrete Pavement

P14 DESIGN STANDARDS FOR CRCP FOR EACH TEXAS ENVIRONMENTAL REGION Center for Transportation Research The University of Texas at Austin.

Design of One Way Slabs CE A433 – RC Design T. Bart Quimby, P.E., Ph.D. Spring 2007.

By Dr. Attaullah Shah Swedish College of Engineering and Technology Wah Cantt. Reinforced Concrete Design-6 Shear Design of Beams.

AHSANULLAH UNIVERSITY OF SCIENCE & TECHNOLOGY DEPT

Advisor: Dr. Bilal El Ariss

Introduction Used for covering spaces in the form of roof or floor

Design of Reinforced Concrete Foundations

Agricultural Hall and Annex Easting Lansing, MI

Supervied by : Eng. Ibrahim Mohammad Prepared by : Atheer Daraghmeh

(i) proper arrangement of reinforcing bars and

Lecture 39 - Design of Two-Way Floor Slab System

Reinforced Concrete Design-2 Introduction

Tapered Beams: Engineers often taper beams so that the beam strength is larger where the bending moment is larger.

Reinforced Concrete Design-7 Design of Continuous beams and Slabs

Reinforced Concrete Design-3 Flexural Design of Beams

STATICS (ENGINEERING MECHANICS-I)

Analysis and Design of Multiple story building

Chapter No. 04 Equilibrium

Determinacy and Stability of Structures

Reinforced Concrete Design-2 Introduction

Outline CH1.Introduction CH2.Preliminary Design CH3.3D Model.

Reinforced Concrete Design-I Design of Axial members

Reinforced Concrete Design-4 Design of T beams

Reinforced Concrete Design-4 Design of T beams

Reinforced Concrete Design-6

Reinforced Concrete Design-4 Design of doubly reinforced beams

CE-401 Reinforced Concrete Design-II

Plain & Reinforced Concrete-1 CE3601

Reinforced Concrete Design-II

AN-NAJAH NATIONAL UNIVRESITY

Analysis And Design Of AS-Shorooq Residential Building

Reinforced Concrete Design-3 Flexural Design of Beams

" multifunctional building design"

Reinforced Concrete Design-4 Design of T beams

Reinforced Concrete Design-II

Presentation transcript:

Reinforced Concrete Design-7 Design of Continuous beams and Slabs By Dr. Attaullah Shah Swedish College of Engineering and Technology Wah Cantt.

Design of Continuous beams Indeterminate and continuous beams Analysis by various classical methods Moment Distribution Method Three moment equation Conjugate beam method Stiffness Method Flexibility methods Any other method you can name? Using software STAD PRO SAP-2000 Using ACI Moment Equation

ACI Moment Coefficient

One way slab system- Min Slab thickness Support Condition Simply supported One end Continuous Two Ends Continuous Cantilever Min Slab thickness

One way slab design-Example

Cut Off bars and bent up options