CAFS On-Line Orientation

Slides:



Advertisements
Similar presentations
Dennis Fire Appliances Operations & use. PTO Step 1 Move slide cover towards the drivers seat to lock out the gearbox Step 2 Select drive on the gear.
Advertisements

Brio 2000 / Brio 2000-M E-Learning Service Manual Rev. 0.0.
Exhaust Gas Recirculation (EGR)
Stanley HP-1 Compact Power Unit.
Full Authority Digital Engine Control
Morgan City Rentals Diesel Jet Pump 6 x 6 Peerless Safe Operating Practices and Procedures.
FoamPro 1600 Series Fully automatic Class A foam ONLY
 Description of PressurePro System  Identify system components  Display and Operational Modes  Sensor alerts  Checking of tire pressures  Manual.
Vehicular Repeater System (VRS) November: What is VRS? VRS is short for Vehicular Repeater System – All of the regular Battalion Chiefs’ buggies.
SAFETY MEETING Off Highway Trucks. Brakes There are four separate controls used for braking Service Brake Retarder Secondary Brake Parking Brake.
CAFS On-Line Orientation
Clean Air Box Usage & Care CABs RAMs CO Monitors.
AccuMax Single Point Injection Operation (See Installation and Operation Manual for detailed instructions)
Normal Operating Parameters Maintenance Schedule Common Problems Normal Operating Parameters Maintenance Schedule Common Problems ClearWater Tech, LLC.
CAFS On-Line Orientation
Bmd Crossvent 3.
CAFS On-Line Orientation Montgomery County Fire & Rescue Service Class A Foam Theory.
Advanced Tool Management Information Module Advanced Tool Management Information Module.
Sensors used in EFI (Electronic Fuel Injection)
2001, 2002 & 3012 Series Operation 2001, 2002 & 3012 Series Operation (See Installation and Operation Manual for detailed instructions)
AccuMax Multi-Point Injection Mechanics
CAFS On-Line Orientation Montgomery County Fire & Rescue Service Operating the CAFS Controllers.
Programming instructions.. To set the time Pool pump and heat pump must be ON. Pictrue 1Picture 2Picture 3 1.Press, the hour will flash (picture 1) 2.To.
Series Operational Training. 2 Water Tank Water Pump Multiple Discharges 2000 Series Line Strainer Foam Tank Electronic Direct Injection Proportioner.
Imago LEAP Recovery Procedure for Cryo-Compressor and Cold Finger The LEAP is equipped with a Uninterrupted Power Supply (UPS). Located in the 19 inch.
ELECTRONIC FUEL INJECTION COMPONENTS
FoamPro Features & Benefits. 139 FoamPro Systems 1600 Series 2000 Series 3012 Model AccuMax Series.
Introduction ► Scope:- Service Diagnostics Routines can use for XXL, Side by Side products with STEALTH user interface with single evaporator fan product.
Water Handling Operations
B757 Review Questions.
ENGINES. VEHICLE / HEAVY EQUIPMENT SAFETY INSPECTION CHECKLIST OF 296.
Engineer Training Pneumatic System Overview. Engineer Training Confidential 2 Working Concept Overview: The Pneumatic System is comprised of:  Y Pistons.
TECHNICAL TRAINING INVERTER-Y
Fan Coils Units Control
ISX12 G & ISL G Cold Weather Operation 1. ISX12 G and ISL G Cold Weather Operation  Cold weather affects CEGR SI natural gas engines differently compared.
To complete installation on electronic models run one wash cycle then click the DIP switch setting no.4 to the on position DIP switch settings.
XAS 375 CD6 Compressors Committed to sustainable productivity
Hydro Multi-B – (2) or (3) CME Pumps in Parallel
Service Section Technical Training December 2005.
STEP 1 Locate the transmission cooler line connection on the vehicle. Identify the correct adapters to be used by referring to the vehicle application.
NN-CS596S Steam Microwave Oven. NN-CS596S Oven Specification.
All Freezer Advance. When the Freezer is first supplied with power or if a power outage occurs, the display will indicate this by flashing the temperature.
Class A Foam 101 Marysville Division of Fire 2009.
Compressed Air Foam System
Relay Pumping Operations Sugar Land Fire Department Driver/Operator-Pumper Academy Spring 2003.
Foam Equipment & Systems Sugar Land Fire Department Driver/Operator-Pumper Academy Spring 2003.
MENU PRINCIPAL. THIS PRESENTATION INCLUDES THE SOURCES OF AIR, THE MAJOR SYSTEM COMPONENTS AND THE WAY THE CONTROLS AND INDICATORS ARE USED TO OPERATE.
MACHINE OPERATION.
Quick Start Guide for Flex Flow Pump
Introduction to Electronic Fuel Systems
Comparison between L – Series / K - series
CAFS On-Line Orientation
Pneumatics Module 9 Time delay valve.
EVAPORATIVE EMISSION CONTROL SYSTEMS
ReverseTap S/W MANUAL.
HIGH PERFORMANCE PRESSURE SYSTEMS.
Keypad Lockout - Available June 15, 2015
TABLE OF CONTENTS A- Unit description B- Microprocessor Control box
Roof Top Unit Overview (MAGNUM)
Chiller Plant Manager (CPM)
CAFS On-Line Orientation
Overview Menus & Settings
Digital Chart Recorder Operation
NRL NRL - Welcome to the NRL Sales Training Program
NRL NRL - Welcome to the NRL Sales Training Program
NRL NRL - Welcome to the NRL Sales Training Program
NRL NRL - Welcome to the NRK Sales Training Program
NRL NRL - Welcome to the NRL Sales Training Program
FOAMPRO 2001 / 2002 Pump Panel. FOAMPRO 2001 / 2002 Pump Panel.
Presentation transcript:

CAFS On-Line Orientation Montgomery County Fire & Rescue Service Operating the CAFS Controllers

Controllers Module Objectives Understand FoamLogix Controller Layout Understand FoamLogix Injection Use Understand CAFSPro Controller Layout Understand CAFSPro Injection Use  MCFRTA 2008

FoamLogix and CAFSPro Controllers FoamLogix Concentrate Injection Control CAFSPro Air Injection Control  MCFRTA 2008

Controllers Both are laid out in similar fashion. On/off button in upper left. Informational display change button in upper right. Arrows control amount of foam or air added. Bar scale across bottom gives visual representation of percent capacity used.  MCFRTA 2008

FoamLogix Controller On/Off Button Switch Displays Button Up and Down Arrows LED Bar Graph  MCFRTA 2008

On/Off Button On/Off Control for Foam Pump Foam Pump Automatically Powers On with road-to-pump engagement Lit LED on bar graph shows you that foam pump is on  MCFRTA 2008

Switch Displays Button Switches between the 4 informational displays  MCFRTA 2008

Informational Display Choices Flow % (Foam Injection) Total Flow Total Foam  MCFRTA 2008

Info Displays - Flow Real-time Flow through the Foam Manifold (gpm, 30-800) This is the combined flow through the manifold. So if you have more than one handline off you will have to estimate percentages to figure out what each handline is flowing. Read from Paddlewheel Flow Sensor This number indicates that there is 116 gpm of water flow passing through the foam manifold at this instant in time.  MCFRTA 2008

Info Displays - % (Foam Injection Rate) #’s to right indicate Foam Injection Rate. Default rate will be 0.3% Letter to left indicates Foam Tank being used (e.g. “A”)  MCFRTA 2008

Info Displays - Total Flow Indicates (in gals.) running total of water flowed through Foam Manifold Starts counting when the system is powered up Q: When is system powered on? A; When pump gear is engaged  MCFRTA 2008

Total Foam Running total of foam concentrate used (gallons) Uses Foam Tank Refill Insurance Company Reimbursement? Usage Tracking in Firehouse  MCFRTA 2008

Up and Down Arrows Adjust Foam Injection Percentage Rates with the Touch of a Button Range of 0.1% to 10.0% You will probably not have to change this under normal conditions. Decrease % Increase %  MCFRTA 2008

LED Bar Graph Visual indicator of Foam Pump capacity being used Just one LED to left lit up simply means the foam pump is on and supplying concentrate. If all the LEDs are lit up all the way to the right, that means that all 5gpm capacity of the foam pump has been used up!  MCFRTA 2008

System Zero To reset Total Flow and Total Foam Press both arrows simultaneously This also resets when system is powered down.  MCFRTA 2008

CAFSPro Controller Power Button Switch Displays Button Up and Down Arrows LED Bar Graph  MCFRTA 2008

Power Button On/Off Control Automatic start when engine is put into pump gear Lit LED indicates power on  MCFRTA 2008

Switch Displays Switch Between the 4 Informational Displays  MCFRTA 2008

Informational Displays Switch Displays Button Air Flow (CFM) Air/Water Ratio Compressor Temperature Hours Run  MCFRTA 2008

Air Flow (CFM) Real Time Air Flow (should be about 1/2 the GPMs of water flow - if flowing wet foam)  MCFRTA 2008

Air to Water Ratio Ratio of Air Injection to Foam Solution (CFM air/GPM water) Ranges from .5 (default setting) all the way to 11  MCFRTA 2008

Compressor Temperature Temperature in degrees Fahrenheit Here the controller is indicating 161F degrees. This is a good operating temperature.  MCFRTA 2008

Hours Run Total Hours the Air Compressor has been running since the system was installed. This compressor has had 15.7 hours of working time.  MCFRTA 2008

Up and Down Arrows Adjust air/water ratio Wet to Dry Range The more air is added the “dryer” the foam Never increase the air when crews are engaged in interior attack. Lessen Air “Wet” Add Air “Dry”  MCFRTA 2008

The more air - the “dryer” the foam Wet to Dry - Controlled by amount of air “Wet” “Fluid” “Dry” The more air - the “dryer” the foam  MCFRTA 2008

Available Air / Water Mixtures Wet 0.5 scfm / 1 gpm (default) 1.0 scfm / 1 gpm 1.5 scfm / 1gpm Medium or Fluid 2.0 scfm / 1 gpm 2.5 scfm / 1 gpm 3.0 scfm / 1 gpm Dry 11.0 scfm / 1 gpm  MCFRTA 2008

LED Bar Graph Visual Indicator of foam consistency (Wet to Dry) Wet >>>>>>>>> Dry  MCFRTA 2008

To Put Compressor In Standby Mode Compressor is engaged and running User taps Power Button once Air Injection Valve then closes & Controller indicates “Stby” Compressor is still turning Instant-On if it should be needed  MCFRTA 2008

To Turn Compressor Completely Off Compressor is engaged and turning Reduce engine speed to idle! Push on/off button and hold 3 Beeps, & Display shows “3,2,1, oFF” Compressor is now not turning  MCFRTA 2008

User Off Mode After turning air compressor off, pump would need to be throttled back up to move water Pump needs to be taken out of gear and re-engaged to bring air compressor back up  MCFRTA 2008

Air Compressor Off When do you need to turn Air Compressor off? If you need to pump plain water or foam solution above 150 psi If failure of foam system and safety interlocks occurs - slug flow & chatter If you run out of foam If you are going to be only using water and want to avoid adding hours to air compressor.  MCFRTA 2008

Review Questions How do you know if the foam pump is on? How do you turn it off? How do you know if the air compressor is on? How do you put the air compressor on standby? What exactly does this mean? How do you turn the air compressor completely off? When should you turn it off?  MCFRTA 2008