Eng. Ibrahim Kuhail Eng. Ahmed Al Afeefy Lab6: Roundness Test Lab 6: Roundness Test 4/3/2019 Eng. Ibrahim Kuhail Eng. Ahmed Al Afeefy

Objective To be familiar with circularity measurements. To know how to use Formtester to measure the following: Roundness. Coaxiality. Concentricity. Radial run-out. Axial run out. Lab6: Roundness Test 4/3/2019

Roundness Roundness is the measure of the sharpness of a particle's edges and corners. Roundness applies to individual circular cross sections of a surface of revolution or of a sphere. Lab6: Roundness Test 4/3/2019

Cylindricity Cylindricity applies to all cross-sections of a cylindrical surface simultaneously. The surface must lie between the two cylindrical surfaces which bound the tolerance zone and are determined by a best-fit nominal cylinder Lab6: Roundness Test 4/3/2019

Coaxiality Coaxiality is the relationship of one axis to another. Coaxiality DIN is defined by a diameter of a cylinder of defined length, with its axis co-axial to the datum axis that will totally enclose the centroids of the planes forming the cylinder axis under evaluation. Coaxiality ISO is defined as the diameter of a cylinder that is coaxial with the datum axis and will just enclose the axis of the cylinder referred for Coaxiality evaluation. Lab6: Roundness Test 4/3/2019

Runout Runout refers to the result of placing a solid of revolution on a spindle such as a lathe, and rotating the part about its central axis while measuring with a dial indicator its surface deviation from perfect roundness. With circular runout, the dial indicator is not moved along the direction of the axis of the part. Circular runout is therefore applied independently at each station along the length of the part as the part is rotated through 360 degrees. Lab6: Roundness Test 4/3/2019

Total Runout: Total Runout: involves moving the dial indicator along the length of the part while the part is rotated, so that it controls the cumulative variations of circularity, cylindricity, straightness, coaxiality, angularity, taper, and profile. Lab6: Roundness Test 4/3/2019

Eccentricity Eccentricity: is the term used to describe the position of the center of a profile relative to some datum point. It is a vector quantity in that it has magnitude and direction. The magnitude of the eccentricity is expressed simply as the distance between the datum point and profile center. The direction is expressed as simply as an angle from the datum point to the profile center. Lab6: Roundness Test 4/3/2019

Concentricity Concentricity is the condition in which the axes of all cross-sectional elements of a surface of revolution are common to the axis of a datum feature. Because the location of the datum axis is difficult to find, it is easier to inspect for cylindricity or runout. Concentricity: is twice the eccentricity and is the diameter of a circle traced by the component center orbiting about the datum axis. Lab6: Roundness Test 4/3/2019

Roundness Measurements Measuring differences in diameter is not sufficient to measure roundness and to measure any component for roundness requiring some form of datum. Roundness is usually assessed by rotational techniques by measuring radial deviations from a rotating datum axis; this axis remains fixed and becomes the main reference for all measurements. Lab6: Roundness Test 4/3/2019

Ways of Measuring Roundness Component rotation : involves rotation of the part while keeping the measuring transducer fixed. The axis of the component is aligned with the axis of the spindle, using a centering and leveling table. A transducer is then used to measure radial variations of the component with respect to the spindle axis. The output of the gauge or transducer consists of three added components: Lab6: Roundness Test 4/3/2019

Ways of Measuring Roundness Rotating the stylus: involves keeping the component fixed while rotating the measuring transducer. Rotate the stylus while keeping the component stationary. This is usually performed on small high precision components but is also useful for measuring large, non-circular, for example measurement of a cylinder bore using this method would not require rotation of the complete engine block. Lab6: Roundness Test 4/3/2019

Reference Circle The output from the gauge can be represented as a polar profile or graph and although this gives a convenient pictorial representation, deriving actual numbers from it can be time consuming and subjective. We therefore need some means of processing the information to give us accurate and repeatable answers. Lab6: Roundness Test 4/3/2019

Circle References Least Square Reference Circle (LSC): is a circle where the sum of areas inside this circle is equal to the sum of the areas outside the circle and kept to a minimum separation. The out of roundness value is the difference between the maximum and minimum radial departure from the reference circle centre. This is a very convenient reference circle to derive, as it is mathematically precise. Lab6: Roundness Test 4/3/2019

Circle References cont. Minimum Zone Circle (MZC) The MZC is defined as two concentric circles positioned to just enclose the measured profile such that their radial departure is a minimum. The roundness value is then given as their radial separation. (RONt) Lab6: Roundness Test 4/3/2019

Circle References cont. Minimum Circumscribed Circle (MCC): This is also known as the ring gauge reference circle and is the smallest circle that totally encloses the profile. Out of roundness is quantified as the largest deviation from this circle (RONt). Lab6: Roundness Test 4/3/2019

Circle References cont. Maximum Inscribed Circle (MIC) :The maximum inscribed circle, sometimes referred to as the plug gauge circle, is the largest circle that is totally enclosed by the profile. Errors are quantified as the maximum radial deviation (RONt) away from this reference circle. Lab6: Roundness Test 4/3/2019

Equipment MMQ10 Formtester for roundness measurement. Vernier Caliper. Lab6: Roundness Test 4/3/2019

Results Note that the Ecc "Eccentricity" value is 0.1 µm <0.5 µm that is the surface is correctly centered. The roundness equals to 1.11 µm which indicates that the edges and the corner of the object is smooth. Tolerance was 10 µm Φ was 172° (angle from the datum point to the profile center). The measurement range was 100 µm Lab6: Roundness Test 4/3/2019

Lab6: Roundness Test 4/3/2019