Working Drawings Legal Documents that Provide All the Visual, Numerical and Textural Information Required to Manufacture a Component, Mechanism or Structure.

Slides:

Advertisements

Similar presentations

15 Detail Drawings Permission granted to reproduce for educational use only. Explain terms and standards related to various types of drawings used in.

Advertisements

Chapter 20 Working Drawings

Getting Started with 3-D CAD by Solid Modeling

Typical phases of a project: 1.Schematic Design 2.Design Development 3.Construction Documents 4.Construction Administration.

Working Drawings Chapter 12.

Engineering 1182 College of Engineering Engineering Education Innovation Center Working Drawings Packet / BOM Rev: , AJPAssembly Drawings1.

Engineering drawings Deborah Munro, Ph.D..

Six Steps of Problem Solving And Engineering Design Process SVES Colleges of Engineering UML – ATP Lecture 2.

Fluid Mechanics –I Surveying –I Mechanics of Solids Building Materials

Engineering Design Dein Shaw. Chapter 1 Introduction What is design?

AP210: Electrical/Electronics PCA Design Information Physical Component Placement Bare Board Geometry Layout items Layers non-planar, conductive & non-conductive.

ME/MECA 238A1 ME/MECA 238A - Mechanical/Mechatronic Design Project I Course notes prepared by G.A. Kallio, based on The Mechanical Design Process, by D.G.

Interpreting and Using Engineering Information. Overview This unit aims to give learners the knowledge and skills needed to use engineering information.

Drawings ACT Objective Realize the organization and intent of construction drawings 2.

Working / Assembly Drawings

IENG 248 D. H. Jensen 6/2/2016Engineering Graphics & 3-D Modeling1 Lecture 08 Working Drawings.

Drawings Review. Drawings Drawings are used to communicate information –Sketch: A drawing done without instruments or measurements, but conveys the general.

Engineering Drawings MeEn 476 Department of Mechanical Engineering Brigham Young University.

Multiview Drawings. Multiview Drawing A multiview drawing is one that shows two or more two-dimensional views of a three- dimensional object. Multiview.

Working Drawings (Production Drawings)

Engineering Graphics with SolidWorks

Introduction to Engineering Reading Working Drawings

Dimensioning & Tolerances 3 Process Sheets PUTTING THE “HOW” IN “HOW IN THE WORLD AM I GOING TO MAKE THIS?”

Bell Work Engineering New Products Read pages of Chapter 19 in the Manufacturing book.

ENGINEERING DRAWINGS Deborah Munro, Ph.D.. What is a Sketch?  Provides visual information about a design  Usually isometric or perspective to give sense.

VIEWNG SYSTEMS There are two ‘viewing systems’ that we use to visually interpret the world around us. What do you think the two ‘viewing systems’ are?

Operation & Maintenance Construction & Logistics 4D/5D Construction Fabrication Documentation Analysis Detail Design Conceptual Design Programming Renovation.

Reading Working Drawing Packets and Section Views

1 MEMB113: ENGINEERING GRAPHICS & CAE 13 ASSEMBLY AND DETAIL DRAWING.

ALIGNING PARTS IN AN ASSEMBLY MAK112E April 20, 2009 Aylin Yenilmez Gürkök.

Working Drawings Stephen W. Crown Ph.D.. Working Drawings A final set of drawings providing all the details and information needed to manufacture and.

ASSEMBLY DRAWINGS. Primarily used to show how a number of components are fitted together to make a complete product unit. The term sub-assembly is commonly.

Working Drawings Packet / BOM ENGR 1182 SolidWorks 10.

Position Statement on Sealed Truss Placement Diagrams for the State of California (including Los Angeles) Overview.

British Standards BS8888.

Reverse Engineering of a Bell-206 Tail Rotor Gearbox Jean-Philippe Roy.

Working Drawings Competency: 00X.00

מהפכות באנגליה.

Working Drawings Competency: 00X.00

Year 9 Subject Selection – Computer Aided Design

MECHANICAL DRAWING WORKING DRAWINGS

Chapter 6 Orthogonal projection

Introduction to New Product Development (Documentation)

Working Drawings (Production Drawings)

Detail Drawings and Assembly Drawings

Unit 16 Engineering Drawing

بسم الله الرحمن الرحيم هل اختلف دور المعلم بعد تطبيق المنهج الحديث الذي ينادي بتوفير خبرات تعليمية مناسبة للطلبة ؟ هل اختلف دور المعلم ؟ ن.ن. ع.

د.سالم بني عطا استراتيجيات التدريس Teaching Strategies

Working Drawings Packet / BOM

What you need in your Manufacturing Specification

The 3P’s The P’s we use to design.

Working Drawings Packet / BOM

Eastern Mediterranean University Department of Mechanical Engineering

The 3P’s The P’s we use to design.

Engineering cycle.

Technical Description

Working Drawings & Layers

D Engineering Drawings.

Working Drawings Chapter 12.

Roof design Bunker Project CDR

Objective: Develop plans for kitchen cabinets.

Working Drawings (Production Drawings)

Assembly drawings Flóra Hajdu B406

What you need in your Manufacturing Specification

Technical Drawings.

PDT176 COMPUTER-AIDED DRAFTING CHAPTER 6 WORKING DRAWING

Presentation transcript:

Working Drawings Legal Documents that Provide All the Visual, Numerical and Textural Information Required to Manufacture a Component, Mechanism or Structure

Working Drawings 1.) Detail Drawings 2.) Assembly Drawings There are 2 Types of Working Drawings 1.) Detail Drawings 2.) Assembly Drawings

Detail Drawings Shape Description Views Sections Size Description Dimensions Tolerances Specifications Finnish Manufacturing Material Quantities Detail drawings provide all visual, numerical and textural information required to construct or manufacture a component or part.

Installation Assemblies Assembly Drawings Design Assemblies Performance Shape Clearances Installation Assemblies Permit Assembly of complicated mechanisms by unskilled persons Bill of Materials Assembly drawings are used to confirm design strategies, provide assembly and installation instruction and verify material and parts used in the manufacture or construction of a mechanism or structure.

Think Build Test Evaluate Modify Working Drawings The Design Process Ends With a Set of Think Build Test Evaluate Modify Working Drawings