Review from LAB #3.

Slides:

Advertisements

Similar presentations

Chapter 3 Stress and Equilibrium

Advertisements

Mechanics of Materials – MAE 243 (Section 002) Spring 2008

Purpose of Mohr’s Circle Visual tool used to determine the stresses that exist at a given point in relation to the angle of orientation of the stress element.

CONTINUUM MECHANICS (STATE OF STRESS)

III. Strain and Stress Basics of continuum mechanics, Strain Basics of continuum mechanics, Stress Reading Suppe, Chapter 3 Twiss&Moores, chapter 15 Additional.

Chapter 3 Rock Mechanics Stress

Geology 3120 Powerpoint notes available online at:

PLANE STRAIN TRANSFORMATION

Principle and Maximum Shearing Stresses ( )

Analysis of Stress and Strain

Analysis of Stress and Strain Review: - Axially loaded Bar - Torsional shaft Questions: (1) Is there any general method to determine stresses on any arbitrary.

27 June 2015GLG510 Advanced Structural Geology Faults and stress.

Announcements Next week lab: 1-3 PM Mon. and Tues. with Andrew McCarthy. Please start on lab before class and come prepared with specific questions Cottonwood.

Stress Transformation

ENGR 220 Section

Chapter Outline Shigley’s Mechanical Engineering Design.

GLG310 Structural Geology. 16 July 2015GLG310 Structural Geology.

Stress II Cauchy formula Consider a small cubic element of rock extracted from the earth, and imagine a plane boundary with an outward normal, n, and an.

IV. Basics of continuum mechanics, Stress Reading Suppe, Chapter 3 Twiss&Moores, chapter 15 Additional References : Jean Salençon, Handbook of continuum.

Theories of Stress and Strain

Content Stress Transformation A Mini Quiz Strain Transformation

Mock Course – Plane Stress Transformation (ref MCHT 213, Hibbeler text) 1 hr 15 min format: –Present Theory/Overview with Power Point, 15 min. –Problem.

Coulomb Stress Changes and the Triggering of Earthquakes

In general stress in a material can be defined by three normal stresses and three shear stresses. For many cases we can simplify to three stress components.

This is the trace of the strain tensor. In general the trace of the strain tensor gives area change in 2-D and volume change in 3-D The principal axes.

1 Principal stresses/Invariants. 2 In many real situations, some of the components of the stress tensor (Eqn. 4-1) are zero. E.g., Tensile test For most.

MEF2 Homework 1 Problem 3.- The state of stress at a point in a structural component is specified by the components (all in MPa) Sigma[x] = -5, Sigma[y]

1.033/1.57 Mechanics of Material Systems (Mechanics and Durability of Solids I) Franz-Josef Ulm Lecture: MWF1 // Recitation: F3:00-4: /1.57 Mechanics.

NB: Uniaxial strain is a type a non-rotational transformation Uniaxial strain.

CHAPTER OBJECTIVES To show how to transform the stress components that are associated with a particular coordinate system into components associated with.

Stress and Strain ( , 3.14) MAE 316 – Strength of Mechanical Components NC State University Department of Mechanical & Aerospace Engineering Stress.

Stress: Stress tensor Principal stresses and directions Maximum shear stresses and directions Failure theories.

Outline Force, vectors Units Normal, shear components Pressure

Triaxial State of Stress at any Critical Point in a Loaded Body

1 Structural Geology Force and Stress - Mohr Diagrams, Mean and Deviatoric Stress, and the Stress Tensor Lecture 6 – Spring 2016.

CTC / MTC 222 Strength of Materials

GLG310 Structural Geology. 18 March 2016GLG310 Structural Geology.

Transformation methods - Examples

Principal Stresses and Strain and Theories of Failure

Strain Linear strain-displacement relationships What is the physical meaning of the strain components? What is the maximum normal and shear strains that.

Continuum Mechanics (MTH487)

EAG 345 – GEOTECHNICAL ANALYSIS

1. PLANE–STRESS TRANSFORMATION

A graphical method of constructing the shear and normal stress tractions on any plane given two principal stresses. This only works in 2-D. Equations.

Stress = Force/Area Force is measured in units of mass*acceleration 1 N (Newton) = 1 kg * m * s-2 another common unit for force is the pound.

Chapter 7 Transformations of Stress and Strain.

Overview Introduction

Mohr’s circle for plane stress

Purpose of Mohr’s Circle

Transformations of Stress and Strain

Transformations of Stress and Strain

Determining Stress State and Sense of Shear

COORDINATE TRANSFORMATION

BDA30303 Solid Mechanics II.

Example 7.01 SOLUTION: Find the element orientation for the principal stresses from Determine the principal stresses from Fig For the state of plane.

Shear Stress - Frictional force per area parallel to the surface which it acts. - it has the units of dv Where: = viscosity = shear.

Concepts of stress and strain

BI-AXIAL STRESS AND MSS THEORY

Sign of the Shear Stress for Flow in a Tube

In-class problem For maximum and minimum stresses of 600 and 200 mega-pascals (MPa) oriented as a vertical vector and a horizontal, E-W striking vector.

The Traction Vector and Stress Tensor

Mechanics of Materials Engr Lecture 14 - Stress Transformation

Mechanics of Materials ENGR Lecture 19 Mohr’s Circle

Mechanics of Materials Engr Lecture 18 - Principal Stresses and Maximum Shear Stress Totally False.

Mechanics of Materials Engr Lecture 1

Mechanics of Materials Engr Lecture 20 More Mohr’s Circles

EQ: Are there other ways to describe the location of a point in the plane other than by giving its x- and y- coordinates?

Compound Normal & Shear Stresses

Copyright ©2014 Pearson Education, All Rights Reserved

Presentation transcript:

Review from LAB #3

Grain-scale shear sense

Homework examples delta-type

Homework examples S-C Mylonite when you know the schistose foliation and shear bands formed at the same time than S-C mylonite. Develop best in a micaceous granite protolith S

Homework examples sigma-type

The Traction Vector and Stress Tensor LAB #4 The Traction Vector and Stress Tensor

From Force to Stress Traction Force Stress at a Point Surface Stress

The Stress Tensor “on in”

Sign Convention Positive Shear Stress Negative Shear Stress Determined by direction of traction acting on negative coordinate face Negative Shear Stress Tractions are positive in negative coordinate direction

Principle Stresses

Stresses in Principal Stress Frame angle is between normal to plane and maximum principal stress orientation

The Mohr Circle a way to visualize the relationship between shear and normal stresses