Point where miners arm was caught removing ice chunk

Slides:



Advertisements
Similar presentations
TapRooT® Summit – Mining
Advertisements

Guards Design Specifications guards: Safety Work Instructions
ProStart Year One Chapter Three
Have We Really Learned From Our Mistakes? Jon Montgomery Ken Heintz Kevin Jones.
Safety Orientation For all employees. Introduction Your agency’s success is built around quality, teamwork and professionalism. Part of this professionalism.
OSHA Subpart Q Concrete and Masonry Construction.
Walking-Working Surfaces: Preventing Falls.
CARDINAL SAFETY RULES There is no greater priority than the safety of each and every employee of Staffaid. For this reason ALL employees must ensure 100%
Fall Protection MIOSHA Part 45 OSHA 1926 Subpart M Holes and Covers
Slip, Trip and Fall Prevention
Machine Guarding.
GENERAL INDUSTRY SAFETY TEST. What does OSHA stand for? 1.Occupational Safety and Health Administration 2.Occupational Safety and Help Administration.
Georgia Tech Safety and Health Consultation Program
Fall Protection.
Pennsylvania Bureau of Deep Mine Safety Slips, Trips and Falls.
Most Frequently Cited Serious Violations Construction – FY 2009 OSHA Federal Standards October 1, 2008 – September 30, 2009.
Electricity Compressed Air Steam Hydraulic Pressure Gas Lines etc.
Excavations & Trenching 1 OSHA 1926 Subpart P Bureau of Workers’ Comp PA Training for Health & Safety (PATHS) PPT
Office of Safety & Health Consultation Office of Safety & Health Consultation presents Focus Four Fall Protection in Construction Focus Four Fall Protection.
Most Frequently Cited Serious Violations Construction 2000.
Walking – Working Surfaces
MNM Fatal Falling Material Accident Falling Material Accident April 11, 2012 (North Carolina) April 11, 2012 (North Carolina) Sand & Gravel Operation.
Bluestone Industry MSHA Inspection Violations. -Berms -Blasting -Electrical -Fire -Guards -HAZCOM Labeling -Health Violations.
Workplace Examinations. Daily Workplace Examinations Who is responsible for making workplace examinations?
Confined Spaces. Definition: Are large enough that an employee can bodily enter them Are not designed for continuous occupancy. Have limited or restricted.
ELECTRICAL General Industry Standards Examination, Installation and Use of Equipment Electrical equipment shall be free from recognized hazards that.
Hazard Recognition and Risk Analysis Why follow safe work practices?
§1926 Subpart M Presented by: ETTA, OSH Division, Fall Protection in Construction.
Safety Focus Work Place Examinations & Hazard Recognition.
Metal and Nonmetal Fatal Accident Review CY
OCCUPATIONAL SAFETY AND HEALTH STANDARDS FOR SHIPYARD EMPLOYMENT.
Session 2: Elevated Work and Fall Protection Session Two Objectives When trainees have completed this session, they should be able to do the following:
This presentation was created by the N.C. Department of Labor for safety and health training. §1926 Subpart M Presented by: ETTA, OSH Division,
Trench Hazards Introduce the module. Trenching & Excavations Continuing Education Third Quarter 2017 Session 3.
Fall Protection for Construction
Hearing protection in excess of ________ decibels requires protection
Walking and Working Surfaces
Safety Orientation For all employees.
29 CFR Subpart F Terminal Facilities
Conveyors.
Pennsylvania Bureau of Deep Mine Safety
ProStart Year One Chapter Three
Most Frequently Cited Serious Violations
Most Frequently Cited Serious Violations
Most Frequently Cited Serious Violations
Most Frequently Cited Serious Violations
Rules To Live By.
Most Frequently Cited Serious Violations
Bins, Hoppers, Silos, Tanks & Surge Piles
Walking-Working Surfaces
Personal Protective Equipment
Walking – Working Surfaces
Most Frequently Cited Serious Violations
HAZCOM Labeling.
Walking-Working Surfaces
MNM Fatal Explosives and Blasting Agents Accident
Most Frequently Cited Serious Violations
ProStart Year One Chapter Three
FALL PROTECTION.
Safety Orientation For all employees.
§ SUBPART L SCAFFOLDS 1.
Walking – Working Surfaces
Walking – Working Surfaces
Safety Orientation For all employees.
General Safety Rules.
Machine Guarding 29 CFR Mushroom / OSHA Alliance General Meeting
SLIPS & FALL PREVENTION
Tripping hazard along travel way
Workplace Examinations
ProStart Year One Chapter Three
Presentation transcript:

Point where miners arm was caught removing ice chunk

A little over an inch opening

56.11001 Safe means of access shall be provided and maintained to all working places. 56.11002 Crossovers, elevated walkways, elevated ramps, and stairways shall be of substantial construction provided with handrails, and maintained in good condition. Where necessary, toe boards shall be provided.

56.20011 Areas where health or safety hazards exists that are not immediately obvious to employees shall be barricaded, or warning signs shall be posted at all approaches.

56.14211-Persons shall not work on top of, under, or work from mobile equipment in a raised position until the equipment has been blocked or mechanically secured to prevent it from rolling or falling accidentally. Also, no fall protection 56.15005

56.14107 Guarding & 56.14213(b) all welding operations shall be well ventilated.

56.20001 Intoxicating beverages and narcotics shall not be permitted or used on or around mines. Persons under the influence of alcohol or narcotics shall not be permitted on the job. 56.20013 Waste receptacles with covers

56. 12032 Inspection and cover plates & 56 56.12032 Inspection and cover plates & 56.12025 Grounding circuit enclosures.